| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO/DIS 15380 |
Lubricants, industrial oils and related products (class L) — Family H (Hydraulic systems) — Specifications for hydraulic fluids in categories HETG, HEPG, HEES and HEPR |
This document specifies the minimum requirements for new hydraulic fluids intended for hydraulic systems when the use of environmentally acceptable products is either mandatory or recommended. The purpose of this International Standard is for the guidance of suppliers and end users of environmentally acceptable hydraulic fluids and for the direction of equipment manufacturers of hydraulic systems.
|
Under development |
|
Edition : 4 |
Number of pages : 25 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
|
| ISO 19291:2016 |
Lubricants — Determination of tribological quantities for oils and greases — Tribological test in the translatory oscillation apparatus |
ISO 19291:2016 describes test methods based on a high-frequency, linear-oscillation test machine to determine tribological quantities like friction, wear, load carrying capacity and extreme pressure behaviour of liquid lubricants (oils) and consistent lubricants (greases) in the ball-on-disk contact geometry.
|
Published |
2016-12 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
|
| ISO 19378:2003 |
Lubricants, industrial oils and related products (class L) — Machine-tool lubricants — Categories and specifications |
ISO 19378:2003 provides the manufacturers and users of machine tools with criteria for the choice among the various categories of lubricants and gives specifications for these lubricants. ISO 19378:2003 facilitates the application of ISO 5169 relating to the presentation of lubrication instructions for machine tools.
|
Published |
2003-03 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
|
| ISO 5662:1978 |
Petroleum products — Electrical insulating oils — Detection of corrosive sulphur |
|
Withdrawn |
1978-02 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
29.040.10
Insulating oils
|
| ISO 20623:2003 |
Petroleum and related products — Determination of the extreme-pressure and anti-wear properties of fluids — Four ball method (European conditions) |
ISO 20623:2003 specifies procedures for the measurement of the extreme-pressure (EP) and anti-wear properties of lubricating oils and fluids by means of the four ball machine. The conditions of test are those that apply in Europe and other areas that have similar electrical supply characteristics (200 V to 250 V, 50 Hz). In North America, the conditions of test are slightly different, but provide a similar ranking of the lubricating properties of fluids. The test conditions are not intended to simulate particular service conditions, but to provide information over a range of standard conditions for the purpose of research, development, quality control and fluid ranking. The output is used in lubricant specifications.
|
Withdrawn |
2003-12 |
Edition : 1 |
Number of pages : 17 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
|
| ISO 20623:2017 |
Petroleum and related products — Determination of the extreme-pressure and anti-wear properties of lubricants — Four-ball method (European conditions) |
ISO 20623:2017 specifies procedures for the measurement of the extreme pressure (EP) and anti-wear properties of liquid lubricants (categories C, D, F, G, H, M, P of ISO 6743‑99), lubricating greases (ISO 6743‑9, category X) and other consistent lubricants. The test conditions are not intended to simulate particular service conditions, but to provide information over a range of standard conditions for the purpose of research, development, quality control and fluid ranking. The output is used in lubricant specifications.
|
Published |
2017-12 |
Edition : 2 |
Number of pages : 16 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
|
| ISO 22285:2018 |
Petroleum products and lubricants — Determination of oil separation from grease — Pressure filtration method |
This document specifies a method for measuring the quantity of oil separated from lubricating grease in the test conditions.
It can be used to predict the behaviour of greases on storage in pails and drums.
This method is not applicable to very soft greases that, during the test, flow unchanged through the sieve.
|
Published |
2018-11 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
|
| ISO 22286:2018 |
Petroleum products and lubricants - Determination of the dropping point of grease with an automatic apparatus |
This document specifies a method for the determination of the dropping point of lubricating grease using an automatic apparatus.
|
Published |
2018-11 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
|
| ISO 23572:2020 |
Petroleum products — Lubricating greases — Sampling of greases |
This document specifies methods for obtaining samples of lubricating grease from production lots or shipments and gives instructions for inspecting greases in sales packages.
|
Published |
2020-03 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
|
| ISO 24254:2007 |
Lubricants, industrial oils and related products (class L) — Family E (internal combustion engine oils) — Specifications for oils for use in four-stroke cycle motorcycle gasoline engines and associated drivetrains (categories EMA and EMB) |
ISO 24254:2007 specifies the requirements of lubricating engine oils (hereinafter referred to as “four-stroke engine oils”) to be used in four-stroke cycle spark ignition gasoline engines employing a common sump containing the lubricating oil for both the engine and associated drivetrain (transmission, clutch, starter) of motorcycles, motor scooters, all-terrain vehicles (ATVs) and related equipment. Classification of four-stroke engine oils is defined in ISO 6743-15. The performance requirements of four-stroke engine oils classified in all of the categories covered by ISO 6743-15, EMA and EMB, are embraced in this specification.
ISO 24254:2007 specifies the performance classification of four-stroke cycle gasoline engine oils, based on physical and chemical properties, and three friction performance indices, which are derived from the frictional properties of the lubricant, according to the JASO T904 test procedure.
|
Published |
2007-10 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
|
| ISO 26422:2011 |
Petroleum and related products — Determination of shear stability of lubricating oils containing polymers — Method using a tapered roller bearing |
ISO 26422:2011 specifies a method of determining the shear stability of polymer-containing lubricating oils, including pressure fluids, by the four-ball tester as specified in ISO 20623, but using a tapered roller bearing. The test results allow prediction of the in-service permanent viscosity loss.
|
Withdrawn |
2011-03 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
|
| ISO 26422:2014 |
Petroleum and related products — Determination of shear stability of lubricating oils containing polymers — Method using a tapered roller bearing |
ISO 26422:2014 specifies a method of determining the shear stability of polymer-containing lubricating oils by the four-ball machine as specified in ISO 20623, but using a tapered roller bearing. The test results allow prediction of the in-service permanent viscosity loss.
NOTE Other International Standards exist which evaluate viscosity loss of polymer-containing oils. The method specified within this International Standard subjects fluids to a higher shear rate than, for example, the diesel injector nozzle shear test described within ISO 20844.[3] It is particularly appropriate for lubricants being used in high shear applications, such as components with gears and roller bearings. In such applications, the shear rate in the ISO 20844 test method can be too low to generate a realistic permanent loss in viscosity of the fluid.
|
Published |
2014-12 |
Edition : 2 |
Number of pages : 10 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
|
| ISO 3871:2000 |
Road vehicles — Labelling of containers for petroleum-based or non-petroleum-based brake fluid |
This International Standard specifies the minimum labelling required for commercial containers of petroleum- and
non-petroleum-based fluids used in the braking and hydraulic systems of road vehicles, including mopeds and
motorcycles.
|
Published |
2000-03 |
Edition : 4 |
Number of pages : 3 |
Technical Committee |
75.120
Hydraulic fluids
;
43.040.40
Braking systems
|
| ISO 4263-2:2003 |
Petroleum and related products — Determination of the ageing behaviour of inhibited oils and fluids — TOST test — Part 2: Procedure for category HFC hydraulic fluids |
ISO 4263-2:2003 specifies a method for the determination of the ageing behaviour of hydraulic fluids of category HFC as defined in ISO 6743-4 and specified in ISO 12922. The ageing is accelerated by the presence of oxygen, water and metal catalysts at elevated temperature, and the degradation of the fluid is followed by changes in pH value and insolubles content. Other parts of ISO 4263 specify similar procedures for the determination of the ageing behaviour of mineral oils and specified categories of fire-resistant fluids used in hydraulic and other applications.
|
Published |
2003-04 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 4263-3:2006 |
Petroleum and related products — Determination of the ageing behaviour of inhibited oils and fluids — TOST test — Part 3: Anhydrous procedure for synthetic hydraulic fluids |
ISO 4263-3:2006 specifies a method for the determination of the ageing behaviour of synthetic hydraulic fluids of categories HFDR, HFDU, HEES and HEPG as defined e.g. in ISO 12922 and ISO 15380. The ageing is accelerated by the presence of oxygen and metal catalysts at elevated temperature, and the degradation of the fluid is followed by changes in acid number. Other parts of ISO 4263 specify similar procedures for the determination of ageing behaviour of mineral oils and specified categories of fire-resistant fluids used in hydraulic and other applications.
|
Withdrawn |
2006-02 |
Edition : 1 |
Number of pages : 21 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 4263-3:2010 |
Petroleum and related products — Determination of the ageing behaviour of inhibited oils and fluids using the TOST test — Part 3: Anhydrous procedure for synthetic hydraulic fluids |
ISO 4263-3:2010 specifies a method for the determination of the ageing behaviour of synthetic hydraulic fluids of categories HFDR, HFDU, HEES and HEPG as defined e.g. in ISO 12922 and ISO 15380. The ageing is accelerated by the presence of oxygen and metal catalysts at elevated temperature, and the degradation of the fluid is followed by changes in acid number. Other parts of ISO 4263 specify similar procedures for the determination of ageing behaviour of mineral oils and specified categories of fire-resistant fluids used in hydraulic and other applications.
Other signs of fluid deterioration, such as the formation of insoluble sludge, catalyst coil corrosion or decrease in viscosity, can occur, which indicate oxidation of the fluid, but are not reflected in the calculated oxidation lifetime. The correlation of these occurrences with field service is under investigation.
ISO 4263-3:2010 can be used to compare the oxidation stability of fluids that are not prone to contamination with water. However, because of the large number of individual field-service applications, the correlation between the results of ISO 4263-3:2010 and actual service performance can vary markedly, and is best judged on experience.
The precision of ISO 4263-3:2010 for synthetic hydraulic fluids is not known because interlaboratory data are not available. ISO 4263-3:2010 might not be suitable for use in specifications or in the event of disputed results as long as these data are not available. However, precision for inhibited turbine oils is given for guidance as an indication of the precision that could be obtained for synthetic hydraulic fluids.
|
Withdrawn |
2010-10 |
Edition : 2 |
Number of pages : 21 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 4263-3:2015 |
Petroleum and related products — Determination of the ageing behaviour of inhibited oils and fluids using the TOST test — Part 3: Anhydrous procedure for synthetic hydraulic fluids |
ISO 4263-3:2015 specifies a method for the determination of the ageing behaviour of synthetic hydraulic fluids of categories HFDU, HEES, HEPG and HETG as defined, for example, in ISO 12922[1] and ISO 15380[2]. The ageing is accelerated by the presence of oxygen and metal catalysts at elevated temperature, and the degradation of the fluid is followed by changes in acid number. Other parts of ISO 4263 specify similar procedures for the determination of ageing behaviour of mineral oils and specified categories of fire-resistant fluids used in hydraulic and other applications.
NOTE Other signs of fluid deterioration, such as the formation of insoluble sludge, catalyst coil corrosion or change in viscosity, can occur which indicate oxidation of the fluid, but are not reflected in the calculated oxidation lifetime. The correlation of these occurrences with field service is under investigation. This test method may be used to compare the oxidation stability of fluids that are not prone to contamination with water. However, because of the large number of individual field-service applications, the correlation between the results of this test and actual service performance can vary markedly, and is best judged on experience. The precision of this test method for synthetic hydraulic fluids is not known because interlaboratory data are not available. This method might not be suitable for use in specifications or in the event of disputed results as long as these data are not available.
|
Published |
2015-11 |
Edition : 3 |
Number of pages : 24 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 4404-1:2001 |
Petroleum and related products — Determination of the corrosion resistance of fire-resistant hydraulic fluids — Part 1: Water-containing fluids |
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 4404-1:2012 |
Petroleum and related products — Determination of the corrosion resistance of fire-resistant hydraulic fluids — Part 1: Water-containing fluids |
ISO 4404-1:2012 specifies a test method to determine the influence on metals of fire-resistant fluids in categories HFA, HFB and HFC, as classified in ISO 6743-4. ISO 4404-1:2012 evaluates the corrosion protection provided by these fluids towards metal components used in hydraulic systems and installations.
|
Published |
2012-07 |
Edition : 2 |
Number of pages : 15 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 20783-1:2011 |
Petroleum and related products — Determination of emulsion stability of fire-resistant fluids — Part 1: Fluids in category HFAE |
ISO 20783‑1:2011 specifies a test method to assess the stability of emulsions within the category HFAE, as defined in ISO 6743-4, made up with waters having clearly-defined concentrations of salts. This method is applicable only to HFAE fluids and not to HFAS fluids.
|
Published |
2011-01 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 4404-2:2003 |
Petroleum and related products — Determination of the corrosion resistance of fire-resistant hydraulic fluids — Part 2: Non-aqueous fluids |
ISO 4404-2:2003 specifies a procedure for the determination of the corrosion-inhibiting properties of non-aqueous hydraulic fluids within the category HFD, as classified in ISO 6743-4.
It provides a qualitative assessment of corrosion of five of the most common metals used in the construction of hydraulic systems, but other metals and/or alloys could be added or substituted for these metals for particular installations.
|
Withdrawn |
2003-08 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 4404-2:2010 |
Petroleum and related products — Determination of the corrosion resistance of fire-resistant hydraulic fluids — Part 2: Non-aqueous fluids |
ISO 4404-2:2010 specifies a procedure for the determination of the corrosion-inhibiting properties of non-aqueous hydraulic fluids within the category HFD, as classified in ISO 6743‑4.
It provides a qualitative assessment of corrosion of five of the most common metals used in the construction of hydraulic systems, but other metals and/or alloys could be added or substituted for these metals for particular installations.
|
Published |
2010-12 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 4404:1998 |
Petroleum and related products — Determination of the corrosion resistance of water-containing fire-resistant fluids for hydraulic systems |
|
Withdrawn |
1998-06 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 4406:1987 |
Hydraulic fluid power — Fluids — Method for coding level of contamination by solid particles |
|
Withdrawn |
1987-11 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
75.120
Hydraulic fluids
;
23.100.60
Filters, seals and contamination of fluids
|
| ISO 4406:1999 |
Hydraulic fluid power — Fluids — Method for coding the level of contamination by solid particles |
|
Withdrawn |
1999-12 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
75.120
Hydraulic fluids
;
23.100.60
Filters, seals and contamination of fluids
|
| ISO 4406:2017 |
Hydraulic fluid power — Fluids — Method for coding the level of contamination by solid particles |
ISO 4406:2017 specifies the code to be used in defining the quantity of solid particles in the fluid used in a given hydraulic fluid power system.
|
Withdrawn |
2017-08 |
Edition : 3 |
Number of pages : 6 |
Technical Committee |
75.120
Hydraulic fluids
;
23.100.60
Filters, seals and contamination of fluids
|
| ISO 4406:2021 |
Hydraulic fluid power — Fluids — Method for coding the level of contamination by solid particles |
This document specifies the code to be used in defining the quantity of solid particles in the fluid used in a given hydraulic fluid power system.
|
Published |
2021-01 |
Edition : 4 |
Number of pages : 6 |
Technical Committee |
75.120
Hydraulic fluids
;
23.100.60
Filters, seals and contamination of fluids
|
| ISO 4925:1978 |
Road vehicles — Non-petroleum base brake fluid |
Specifies the characteristics and the test methods for the non-petroleum base brake fluid used in the hydraulic brake systems. The brake fluid described is for use in brake systems equipped with seals, cups or double-lipped type gland seals made from natural rubber, styrene-butadiene rubber, and ethylene-propylene elastomer.
|
Withdrawn |
1978-09 |
Edition : 1 |
Number of pages : 22 |
Technical Committee |
75.120
Hydraulic fluids
;
43.040.40
Braking systems
|
| ISO 4925:2005 |
Road vehicles — Specification of non-petroleum-base brake fluids for hydraulic systems |
ISO 4925:2005 specifies non-petroleum-base fluids used in road-vehicle hydraulic brake and clutch systems that are designed for use with such fluids and equipped with seals, cups or double-lipped type gland seals made of styrene-butadiene rubber (SBR) and ethylene-propylene elastomer (EPDM).
|
Withdrawn |
2005-02 |
Edition : 2 |
Number of pages : 25 |
Technical Committee |
75.120
Hydraulic fluids
;
43.040.40
Braking systems
|
| ISO 4925:2020 |
Road vehicles — Specification of non-petroleum-based brake fluids for hydraulic systems |
This document provides the specifications, requirements and test methods, for non-petroleum-based fluids used in road-vehicle hydraulic brake and clutch systems that are designed for use with such fluids and equipped with seals, cups or double-lipped type gland seals made of styrene-butadiene rubber (SBR) and ethylene-propylene elastomer (EPDM).
|
Published |
2020-07 |
Edition : 3 |
Number of pages : 25 |
Technical Committee |
75.120
Hydraulic fluids
;
43.040.40
Braking systems
|
| ISO 8340:2005 |
Building construction — Sealants — Determination of tensile properties at maintained extension |
ISO 8340:2005 specifies a method for the determination of the tensile properties at maintained extension of sealants used in joints in building construction.
|
Published |
2005-06 |
Edition : 2 |
Number of pages : 5 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 4926:1978 |
Road vehicles — Hydraulic brake systems — Non-petroleum base reference fluids |
Specifies the composition and some characteristics of two reference fluids used for the testing of hydraulic braking systems and components mounted on road vehicles. Tabulates the 24 constituents and their composition by mass % for the ISO compatibility fluid, and the 6 constituents and their composition by mass % for the ISO fluid for storage corrosion test.
|
Withdrawn |
1978-02 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
75.120
Hydraulic fluids
;
43.040.40
Braking systems
|
| ISO 4926:2006 |
Road vehicles — Hydraulic braking systems — Non-petroleum-base reference fluids |
ISO 4926:2006 specifies the composition and characteristics of a reference fluid used for the compatibility testing of hydraulic braking systems and components mounted on road vehicles.
|
Withdrawn |
2006-11 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
75.120
Hydraulic fluids
;
43.040.40
Braking systems
|
| ISO 4926:2020 |
Road vehicles — Hydraulic braking systems — Non-petroleum-based reference fluid |
This document specifies the composition and characteristics of a reference fluid used for the compatibility testing of hydraulic braking systems and components mounted on road vehicles.
|
Published |
2020-07 |
Edition : 3 |
Number of pages : 2 |
Technical Committee |
75.120
Hydraulic fluids
;
43.040.40
Braking systems
|
| ISO 6073:1980 |
Hydraulic fluid power — Petroleum fluids — Prediction of bulk moduli |
|
Withdrawn |
1980-11 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 6073:1997 |
Petroleum products — Prediction of the bulk moduli of petroleum fluids used in hydraulic power systems |
|
Withdrawn |
1997-12 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 6743-4:1982 |
Lubricants, industrial oils and related products (class L) — Classification — Part 4: Family H (Hydraulic systems) |
|
Withdrawn |
1982-11 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 6743-4:1999 |
Lubricants, industrial oils and related products (class L) — Classification — Part 4: Family H (Hydraulic systems) |
|
Withdrawn |
1999-10 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 6743-4:2015 |
Lubricants, industrial oils and related products (class L) — Classification — Part 4: Family H (Hydraulic systems) |
ISO 6743-4:2015 establishes the detailed classification of fluids of Family H (Hydraulic systems) which belong to class L (Lubricants, industrial oils, and related products). It is intended to be read in conjunction with ISO 6743‑99. This classification system does not include automotive brake fluids or aircraft hydraulic fluids.
|
Published |
2015-08 |
Edition : 3 |
Number of pages : 4 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 7308:1987 |
Road vehicles — Petroleum-based brake-fluid for stored-energy hydraulic brakes |
The brake-fluid specified is for use in road vehicle brake systems equipped with rubber cups and seals (butadiene-acrylonitrile copolymer or equivalent). It is for use in hydraulic brake systems equipped with a pump; it may also be used in other systems without a pump. Not for use under arctic conditions.
|
Published |
1987-12 |
Edition : 1 |
Number of pages : 20 |
Technical Committee |
75.120
Hydraulic fluids
;
43.040.40
Braking systems
|
| ISO 7309:1985 |
Road vehicles — Hydraulic braking systems — ISO reference petroleum base fluid |
Specifies the composition (table 1) and required characteristics (table 2) of a reference fluid used for the testing of hydraulic braking systems and components mounted on road vehicles. Tabulates the physical and chemical characteristics together with units and values and the method of determination to be used.
|
Published |
1985-04 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
75.120
Hydraulic fluids
;
43.040.40
Braking systems
|
| ISO 7745:1989 |
Hydraulic fluid power — Fire-resistant (FR) fluids — Guidelines for use |
Provides guidelines detailing, for the various categories of fluids, operational characteristics, advantages and disadvantages, and the factors affecting the choice to be made amongst these various categories. Specifies also precautions which should be adopted to reduce difficulties arising from the use of such fluids, as well as the precautions which are necessary when replacing fluids with fluids from different categories. The installation of hydraulic circuits with respect to fire-resistant fluids is also described.
|
Withdrawn |
1989-08 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 8394-1:2010 |
Building construction — Jointing products — Part 1: Determination of extrudability of sealants |
ISO 8394-1:2010 specifies a method for determining the extrudability of sealants. The method is for use in testing the extrudability of a sealant.
|
Published |
2010-10 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 7745:2010 |
Hydraulic fluid power — Fire-resistant (FR) fluids — Requirements and guidelines for use |
ISO 7745:2010 specifies the operational characteristics for the various categories of fire-resistant fluids defined by ISO 6743-4. ISO 7745:2010 details the factors to be considered when selecting a fluid from these categories for a proposed application.
ISO 7745:2010 identifies difficulties which might arise from the use of such fluids and indicates how they may be minimized. Appropriate procedures are given for replacing one fluid with another from a different category. Health and safety aspects when handling and disposing of fire-resistant fluids are also covered.
ISO 7745:2010 does not apply to fire-resistant fluids used in the hydraulic systems of commercial or military aircraft. The appropriate aviation standards are also usually applied where aircraft hydraulic fluids are filled into ground-based systems.
|
Published |
2010-12 |
Edition : 2 |
Number of pages : 23 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO/DIS 7745 |
Hydraulic fluid power — Fire-resistant (FR) fluids — Requirements and guidelines for use |
This document specifies the operational characteristics for the various categories of fire-resistant fluids defined by ISO 6743-4. This document details the factors to be considered when selecting a fluid from these categories for a proposed application.
This document identifies difficulties which might arise from the use of such fluids and indicates how they may be minimized. Appropriate procedures are given for replacing one fluid with another from a different category. Health and safety aspects when handling and disposing of fire-resistant fluids are also covered.
This document does not apply to fire-resistant fluids used in the hydraulic systems of commercial or military aircraft. The appropriate aviation standards are also usually applied where aircraft hydraulic fluids are filled into ground-based systems.
|
Under development |
|
Edition : 3 |
Number of pages : 24 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 9128:1987 |
Road vehicles — Graphical symbols to designate brake fluid types |
Specifies the graphical symbols and colours used to identify, on road vehicles, the correct type of fluid to be used for: petroleum-base brake fluid systems; non-petroleum-base brake fluid systems. The same symbols are also used for labelling the fluid containers (ISO 3871). Non-petroleum-base fluids (ISO 4925, glycol type) and petroleum-base fluids (ISO 7308) are totally incompatible, requiring the use of different seal materials.
|
Withdrawn |
1987-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
75.120
Hydraulic fluids
;
01.080.20
Graphical symbols for use on specific equipment
;
43.040.40
Braking systems
|
| ISO 9128:2006 |
Road vehicles — Graphical symbols to designate brake fluid types |
ISO 9128:2006 specifies the graphical symbols and colours used to identify, on road vehicles, the correct type of fluid to be used for:
petroleum-base brake fluid systems; andnon-petroleum-base brake fluid systems.
|
Published |
2006-05 |
Edition : 2 |
Number of pages : 5 |
Technical Committee |
75.120
Hydraulic fluids
;
01.080.20
Graphical symbols for use on specific equipment
;
43.040.40
Braking systems
|
| ISO 10050:2005 |
Lubricants, industrial oils and related products (class L) — Family T (Turbines) — Specifications of triaryl phosphate ester turbine control fluids (category ISO-L-TCD) |
ISO 10050:2005 specifies the characteristics of unused triaryl phosphate ester fluids for turbine governor controls and other hydraulic systems in electrical power stations.
|
Published |
2005-10 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 11158:1997 |
Lubricants, industrial oils and related products (class L) — Family H (hydraulic systems) — Specifications for categories HH, HL, HM, HR, HV and HG |
|
Withdrawn |
1997-12 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 11158:2009 |
Lubricants, industrial oils and related products (class L) — Family H (hydraulic systems) — Specifications for categories HH, HL, HM, HV and HG |
ISO 11158:2009 specifies the minimum requirements for new mineral oil hydraulic fluids and is intended for hydraulic systems, particularly for hydrostatic hydraulic fluid power application. The purpose of ISO 11158:2009 is for the guidance of suppliers and end users of mineral oil hydraulic fluids and for the direction of equipment manufacturers of hydraulic systems.
ISO 11158:2009 is written in a general form so that its application can accommodate various climatic conditions throughout the world. ISO 11158:2009 also stipulates the requirements for mineral-oil hydraulic fluids at the time of delivery.
Classification of fluids used in hydraulic applications is defined in ISO 6743-4. Of the categories covered by ISO 6743-4, only five types of mineral oil based fluids are embraced in ISO 11158:2009. These categories are HH, HL, HM, HV and HG.
|
Published |
2009-09 |
Edition : 2 |
Number of pages : 15 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO/DIS 11158 |
Lubricants, industrial oils and related products (class L) — Family H (hydraulic systems) — Specifications for categories HH, HL, HM, HV and HG |
This document specifies the minimum requirements for new mineral oil hydraulic fluids and is intended for hydraulic systems, particularly for hydrostatic hydraulic fluid power application. The purpose of this document is for the guidance of suppliers and end users of mineral oil hydraulic fluids and for the direction of equipment manufacturers of hydraulic systems.
|
Under development |
|
Edition : 3 |
Number of pages : 22 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 11365:2017 |
Petroleum and related products — Requirements and guidance for the maintenance of triaryl phosphate ester turbine control fluids |
ISO 11365:2017 is applicable to the use of triaryl phosphate esters as fire-resistant fluids for turbine control and other hydraulic systems in power generation. These fluids fall under category HFDR of ISO 6743‑4[1].
ISO 11365:2017 is intended to:
- assist the power equipment operator to maintain the fluid in a condition that will ensure the safe and reliable operation of the turbine while maximizing fluid life;
- recommend procedures for examining consignments of new fluid and monitoring the fluid in use;
- provide information on the safe handling, storage and disposal of the fluid;
- offer background information on the causes of fluid degradation.
|
Published |
2017-09 |
Edition : 1 |
Number of pages : 20 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO/TS 11365:2011 |
Petroleum and related products — Guidance for the maintenance and use of triaryl phosphate ester turbine-control fluids |
ISO/TS 11365:2011 applies to the use of triaryl phosphate esters as fire-resistant fluids for turbine control and other hydraulic systems in power generation.
ISO/TS 11365:2011 is intended to
help power equipment operators appreciate the important properties of triaryl phosphate esters;
provide information on their safe handling, storage and use.
ISO/TS 11365:2011 addresses the causes of fluid deterioration and sets out procedures for examining consignments of new fluid, for monitoring the fluid in use and for maintaining an adequate fluid condition.
|
Withdrawn |
2011-03 |
Edition : 1 |
Number of pages : 19 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 12922:1999 |
Lubricants, industrial oils and related products (class L) — Family H (Hydraulic systems) — Specifications for categories HFAE, HFAS, HFB, HFC, HFDR and HFDU |
|
Withdrawn |
1999-10 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 12922:1999/Cor 1:2001 |
Lubricants, industrial oils and related products (class L) — Family H (Hydraulic systems) — Specifications for categories HFAE, HFAS, HFB, HFC, HFDR and HFDU — Technical Corrigendum 1 |
|
Withdrawn |
2001-02 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 12922:2012 |
Lubricants, industrial oils and related products (class L) — Family H (Hydraulic systems) — Specifications for hydraulic fluids in categories HFAE, HFAS, HFB, HFC, HFDR and HFDU |
ISO 12922:2012 specifies the minimum requirements of unused fire-resistant and less-flammable hydraulic fluids for hydrostatic and hydrodynamic systems in general industrial applications. It is not intended for use in aerospace or power-generation applications, where different requirements apply. It provides guidance for suppliers and end users of these less hazardous fluids and to the manufacturers of hydraulic equipment in which they are used.
Of the categories covered by ISO 6743-4, which classifies the different types of fluids used in hydraulic applications, only the following are detailed in this International Standard: HFAE, HFAS, HFB, HFC, HFDR and HFDU.
|
Withdrawn |
2012-12 |
Edition : 2 |
Number of pages : 10 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 12922:2020 |
Lubricants, industrial oils and related products (class L) — Family H (hydraulic systems) — Specifications for hydraulic fluids in categories HFAE, HFAS, HFB, HFC, HFDR and HFDU |
This document specifies the minimum requirements of unused fire-resistant and less flammable hydraulic fluids for hydrostatic and hydrodynamic systems in general industrial applications. It is not intended for use in aerospace or power-generation applications, where different requirements apply. It provides guidance for suppliers and end users of these less hazardous fluids and to the manufacturers of hydraulic equipment in which they are used.
Of the categories covered by ISO 6743-4, which classifies the different types of fluids used in hydraulic applications, only the following are detailed in this document: HFAE, HFAS, HFB, HFC, HFDR and HFDU.
Types HFAE, HFAS, HFB, HFC and HFDR are "fire-resistant" fluids as defined by ISO 5598. Most HFDU fluids, while displaying an improvement in combustion behaviour over mineral oil, fall outside this definition and are more appropriately considered as "less flammable" fluids.
|
Published |
2020-02 |
Edition : 3 |
Number of pages : 11 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 20763:2004 |
Petroleum and related products — Determination of anti-wear properties of hydraulic fluids — Vane pump method |
ISO 20763:2004 specifies procedures for the determination of steel-on-steel anti-wear properties of hydraulic fluids by means of performance in a vane-type hydraulic pump. ISO 20763:2004 covers a range of hydraulic fluids, both anhydrous and aqueous, intended for applications where high-speed sliding contacts, such as those found in a vane pump, are encountered.
For mineral oils of categories HM and HV, and fire-resistant fluids of category HFD, the method is applicable to viscosity classes ISO VG 32, ISO VG 46 and ISO VG 68, as specified in ISO 3448. Under different specified conditions, the method is applicable to aqueous fire-resistant hydraulic fluids in categories HFA, HFB and HFC, as specified in ISO 12922, within the same viscosity classes.
|
Published |
2004-07 |
Edition : 1 |
Number of pages : 17 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 20783-1:2003 |
Petroleum and related products — Determination of emulsion stability of fire-resistant fluids — Part 1: Fluids in category HFAE |
ISO 20783-1:2003 specifies a test method to assess the stability of emulsions within the category HFAE, as defined in ISO 6743-4, made up with waters having clearly-defined concentrations of salts. This method is applicable only to HFAE fluids and not to HFAS fluids.
|
Withdrawn |
2003-12 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 20783-2:2003 |
Petroleum and related products — Determination of emulsion stability of fire-resistant fluids — Part 2: Fluids in category HFB |
ISO 20783-2:2003 specifies three test methods to assess the stability of emulsions within the category HFB, as defined in ISO 6743-4.
Method A describes a method for the determination of stability during storage at ambient temperature [(20 ± 2) °C] and is applicable to HFB and HFB.LT fluids.
Method B describes a method for the determination of stability during storage at medium temperature [(70 ± 2) °C] and is again applicable to HFB and HFB.LT fluids.
Method C describes a method for the determination of stability during storage at low temperature [(-10 ± 2) °C] and is applicable only to HFB.LT fluids.
|
Published |
2003-12 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 20843:2003 |
Petroleum and related products — Determination of pH of fire-resistant fluids within categories HFAE, HFAS and HFC |
ISO 20843:2003 specifies a test method to determine the pH value of non-flammable fluids within categories HFAE, HFAS and HFC, as classified in ISO 6743-4:1999.
|
Withdrawn |
2003-09 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 20843:2011 |
Petroleum and related products — Determination of pH of fire-resistant fluids within categories HFAE, HFAS and HFC |
ISO 20843:2011 specifies a test method to determine the pH value of fire-resistant fluids within categories HFAE, HFAS and HFC, as classified in ISO 6743‑4.
|
Published |
2011-01 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
75.120
Hydraulic fluids
|
| ISO 2137:1985 |
Petroleum products — Lubricating grease and petrolatum — Determination of cone penetration |
Section One gives four procedures for determination of the consistency by measurement of the penetration of a standard cone. Section Two gives methods, when only small samples are available, by the use of cones a half or quarter scale of that used in Section One. The methods are applicable to penetrations of 175 to 385 units. They are not intended to replace the full-scale penetration.
|
Withdrawn |
1985-11 |
Edition : 2 |
Number of pages : 15 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
;
75.140
Waxes, bituminous materials and other petroleum products
|
| ISO 2137:2007 |
Petroleum products and lubricants — Determination of cone penetration of lubricating greases and petrolatum |
ISO 2137:2007 specifies several methods for the empirical estimation of the consistency of lubricating greases and petrolatum by measuring the penetration of a standardized cone. Four procedures are specified for determining the consistency of lubricating greases by measuring the penetration of a full-scale cone for unworked, worked, prolonged worked and block penetrations for penetrations of up to 500 units.
ISO 2137:2007 specifies methods for determining the consistency of lubricating greases when only small samples are available, by the use of cones a half-scale or quarter-scale for the listed methods, applicable to greases having penetrations of 175 units to 385 units using the full-scale cone.
|
Withdrawn |
2007-12 |
Edition : 3 |
Number of pages : 22 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
;
75.140
Waxes, bituminous materials and other petroleum products
|
| ISO 2137:2020 |
Petroleum products and lubricants — Determination of cone penetration of lubricating greases and petrolatum |
This document specifies several methods for the empirical estimation of the consistency of lubricating greases and petrolatum by measuring the penetration of a standardized cone.
|
Published |
2020-05 |
Edition : 4 |
Number of pages : 22 |
Technical Committee |
75.100
Lubricants, industrial oils and related products
;
75.140
Waxes, bituminous materials and other petroleum products
|
| ISO 2207:1980 |
Petroleum waxes — Determination of congealing point |
The procedure specified allows the determination of the temperature at which a sample being cooled develops a set or resistance to flow. At that temperature the product may be at or close to the solid phase. In the case of petrolatums, congealing is associated with the formation of a gel structure as the sample cools.
|
Published |
1980-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
75.140
Waxes, bituminous materials and other petroleum products
|
| ISO 2908:1974 |
Petroleum waxes — Determination of oil content |
Includes a test procedure for products having a congealing point of 30 °C or higher and containing not more than 15 % of oil. This content may have significant effects on several of its properties, such as strength, hardness, flexibility, scuff resistance, coefficient of friction, coefficient of expansion, melting point, and oil staining.
|
Withdrawn |
1974-08 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
75.140
Waxes, bituminous materials and other petroleum products
|
| ISO 3841:1977 |
Petroleum waxes — Determination of melting point (cooling curve) |
The method specified is unsuitable for waxes of the petroleum group, the microcrystalline waxes, or blends of such waxes with paraffin wax or scale wax. The test is particularly applicable to substances that are rather highly paraffinic or crystalline in nature.
|
Withdrawn |
1977-02 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
75.140
Waxes, bituminous materials and other petroleum products
|
| ISO 6244:1982 |
Petroleum waxes and petrolatums — Determination of drop melting point |
May be used to measure the melting acharacteristics of petrolatums and other high viscosity petroleum waxes. Additional methods used are given in ISO 3841 and ISO 2207. Results obtained may differ, depending on the method used. For pharmaceutical petrolatum, the use of this procedure is usually preferred. In the annex, the specification for thermometers is given.
|
Published |
1982-02 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
75.140
Waxes, bituminous materials and other petroleum products
|
| ISO 3867:1982 |
Agglomerated cork material of expansion joints for construction and building — Test methods |
Covers filler material between elements of construction in concrete or in similar applications, e.g. runways, roads, dams, buildings. The following characteristics are determind: thickness, tensile strength, compression, compression set, transversal expansion, swelling in boiling water, behaviour in hydrochloric acid at 100 °C, and behaviour after artificial ageing.
|
Withdrawn |
1982-03 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
79.100
Cork and cork products
;
91.100.50
Binders. Sealing materials
|
| ISO 3867:2001 |
Composition cork — Expansion joint fillers — Test methods |
|
Withdrawn |
2001-07 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
79.100
Cork and cork products
;
91.100.50
Binders. Sealing materials
|
| ISO 3867:2017 |
Composition cork — Expansion joint fillers — Test methods |
ISO 3867:2017 specifies test methods to determine the following characteristics of the composition cork intended to be used as a joint filler of expansion joints of concrete or other construction materials:
- apparent density;
- expansion in water;
- compression;
- recovery;
- extrusion;
- water absorption.
These test methods apply to agglomerated cork joint filler with a nominal thickness ranging from 6,3 mm to 25 mm.
|
Published |
2017-07 |
Edition : 3 |
Number of pages : 7 |
Technical Committee |
79.100
Cork and cork products
;
91.100.50
Binders. Sealing materials
|
| ISO 3869:1981 |
Agglomerated cork — Filler material of expansion joints for construction and buildings — Characteristics, sampling and packing |
Establishes the relevant values of the properties determined by the test methods specified in ISO 3867. Applies to filler material between elements of construction in concrete or in similar applications, e.g. runways, roads, dams, buildings.
|
Withdrawn |
1981-12 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
79.100
Cork and cork products
;
91.100.50
Binders. Sealing materials
|
| ISO 3869:2001 |
Composition cork — Expansion joint fillers — Specifications, packaging and marking |
|
Withdrawn |
2001-07 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
79.100
Cork and cork products
;
91.100.50
Binders. Sealing materials
|
| ISO 3869:2017 |
Agglomerated cork — Expansion joint fillers — Specifications, packaging and marking |
ISO 3869:2017 specifies the characteristics of composition cork intended to be used as expansion joint filler between concrete elements or other construction products.
|
Published |
2017-07 |
Edition : 3 |
Number of pages : 3 |
Technical Committee |
79.100
Cork and cork products
;
91.100.50
Binders. Sealing materials
|
| ISO 3934:1978 |
Rubber building gaskets — Materials in preformed solid vulcanizates used for sealing glazing and panels — Specification |
Describes four types of material, where both resistance to creep under load and weather resistance are essential. Defines requirements for gaskets used in buildings (such as U-channel gaskets). Does not cover structural gaskets of the locking compression type. A table summarizes the general requirements.
|
Withdrawn |
1978-09 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
83.140.50
Seals
;
91.100.50
Binders. Sealing materials
|
| ISO 3934:2002 |
Rubber, vulcanized and thermoplastic — Preformed gaskets used in buildings — Classification, specifications and test methods |
This International Standard specifies a system of classification of materials used in preformed gaskets for buildings. It applies to the following products:
gaskets for use round the inside of door or window casings, i.e. weatherstripping (dynamic gaskets);gaskets for glazing (static gaskets);gaskets for use round infilling;gaskets for use between façade parts;gaskets for use between masonry walls.
In addition to specifying the characteristics required for the constituent materials, some functional tests on the gaskets themselves are specified. The corresponding test procedures are given in the annexes.
This International Standard applies to preformed gaskets made from vulcanized or thermoplastic rubber, whatever the material of which the structure intended to receive them is made. It also applies to preformed gaskets made of cellular rubber designed for use at temperatures between 20 °C and +55 °C and between 40 °C and +70 °C.
|
Withdrawn |
2002-09 |
Edition : 2 |
Number of pages : 19 |
Technical Committee |
83.140.50
Seals
;
91.100.50
Binders. Sealing materials
|
| ISO 4899:1982 |
Textile glass reinforced thermosetting plastics — Properties and test methods |
|
Withdrawn |
1982-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
83.120
Reinforced plastics
|
| ISO 3934:2021 |
Rubber, vulcanized and thermoplastic — Preformed gaskets used in buildings — Classification, specifications and test methods |
This document specifies a system of classification of materials used in preformed gaskets for buildings. It applies to the following products:
a) gaskets for use round the inside of door or window casings, i.e. weatherstripping (dynamic gaskets);
b) gaskets for glazing (static gaskets);
c) gaskets for use round infilling;
d) gaskets for use between facade parts;
e) gaskets for use between masonry walls.
In addition to specifying the characteristics required for the constituent materials, some functional tests on the gaskets themselves are specified. The corresponding test procedures are given in Annexes A to E.
This document applies to preformed gaskets made from vulcanized or thermoplastic rubber. It also applies to preformed gaskets made of cellular rubber designed for use at temperatures between −20 °C and +55 °C (thermal conditions category P1) and between −40 °C and +70 °C (thermal conditions category P3) (see Clause 4).
|
Published |
2021-10 |
Edition : 3 |
Number of pages : 19 |
Technical Committee |
83.140.50
Seals
;
91.100.50
Binders. Sealing materials
|
| ISO 4635:1982 |
Rubber, vulcanized — Preformed compression seals for use between concrete motorway paving sections — Specification for material |
Does not cover design or dimensions of seals, but tolerances should be described in accordance with ISO 3302. Is based on experience with chloroprene rubber. Work is in progress to take account of material development in this field. The requirements are summarized in a table. The annex refers to the determination of recovery.
|
Withdrawn |
1982-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
83.140.50
Seals
;
91.100.50
Binders. Sealing materials
|
| ISO 4635:2011 |
Rubber, vulcanized — Preformed joint seals for use between concrete paving sections of highways — Specification |
ISO 4635:2011 specifies requirements for material for preformed vulcanized rubber joint seals used between concrete paving sections of highways.
It is applicable to seals for joints in new concrete highways as well as to maintenance work on such highways.
It does not cover the design or dimensions of seals, but general requirements for finished seals are given.
|
Published |
2011-02 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
83.140.50
Seals
;
91.100.50
Binders. Sealing materials
|
| ISO 4781:2022 |
Building and civil engineering sealants — Determination of application life |
The document specifies a method for the determination of application life of multi-component sealants.
NOTE The application life test method is only applicable to multi-part sealants.
|
Published |
2022-03 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 4784:2022 |
Building and civil engineering sealants — Determination of surface cure time |
The document specifies a method for the determination of the surface cure of one- and multi-component sealants.
|
Published |
2022-01 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 5892:1981 |
Rubber building gaskets — Materials for preformed solid vulcanized structural gaskets — Specification |
Specifies material requirements in sealing operations where both resistance to stress relaxation and resistance to weathering are essential. Relates particularly to gaskets of the lock-strip type. Does not give the material requirements for gaskets used for sealing glazing and panels. An annex with figures refers to lip seal pressure measurement.
|
Withdrawn |
1981-10 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
83.140.50
Seals
;
91.100.50
Binders. Sealing materials
|
| ISO 5892:2013 |
Rubber building gaskets — Materials for preformed solid vulcanized structural gaskets — Specification |
ISO 5892:2013 specifies material requirements for preformed, solid vulcanized rubber structural gaskets in sealing and supporting applications for buildings.
|
Published |
2013-06 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
83.140.50
Seals
;
91.100.50
Binders. Sealing materials
|
| ISO/DIS 5892 |
Rubber building gaskets — Materials for preformed solid vulcanized structural gaskets — Specification |
ISO 5892:2013 specifies material requirements for preformed, solid vulcanized rubber structural gaskets in sealing and supporting applications for buildings.
|
Under development |
|
Edition : 3 |
Number of pages : 11 |
Technical Committee |
83.140.50
Seals
;
91.100.50
Binders. Sealing materials
|
| ISO 6927:1981 |
Building construction — Jointing products — Sealants — Vocabulary |
Defines technical terms for sealants for building purposes and applies to joints filled with hardening, plastic or elastic materials which are not preformed. Does not include all necessary technical terms on jointing products. Material properties are defined in general terms without reference to related quantitative aspects.
|
Withdrawn |
1981-08 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
01.040.91
Construction materials and building (Vocabularies)
;
91.100.50
Binders. Sealing materials
|
| ISO 6927:2012 |
Buildings and civil engineering works — Sealants — Vocabulary |
ISO 6927:2012 defines technical terms for self-levelling and gun-grade (gunnable) sealants for above ground exposed structures. It is not applicable to sealants used in roads and airfields, sealants for water retaining structures, or structural glazing sealants.
|
Withdrawn |
2012-07 |
Edition : 2 |
Number of pages : 21 |
Technical Committee |
01.040.91
Construction materials and building (Vocabularies)
;
91.100.50
Binders. Sealing materials
|
| ISO 6927:2021 |
Building and civil engineering sealants — Vocabulary |
This document defines technical terms for self-levelling and gun-grade (gunnable) sealants for above-ground exposed structures.
|
Published |
2021-03 |
Edition : 3 |
Number of pages : 10 |
Technical Committee |
01.040.91
Construction materials and building (Vocabularies)
;
91.100.50
Binders. Sealing materials
|
| ISO 7389:1982 |
Building construction — Jointing products — Determination of elastic recovery |
|
Withdrawn |
1982-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 7389:1987 |
Building construction — Jointing products — Determination of elastic recovery |
Specifies a conventional method for the determination of the elastic recovery of sealants after extension and applies to sealants used in joints in building construction. Contains test method (preparation and conditioning of test specimen, procedure), expression of results, and test report.
|
Withdrawn |
1987-11 |
Edition : 2 |
Number of pages : 3 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 7389:2002 |
Building construction — Jointing products — Determination of elastic recovery of sealants |
This International Standard specifies a method for the determination of the elastic recovery of sealants after maintained extension.
|
Published |
2002-10 |
Edition : 3 |
Number of pages : 5 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 7390:1982 |
Building construction — Jointing products — Determination of resistance to flow |
|
Withdrawn |
1982-12 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 7390:1987 |
Building construction — Jointing products — Determination of resistance to flow |
Specifies a method for the determination of resistance to flow of sealants to be used in joints of vertical surfaces of building construction. Describes test method (principle, apparatus, preparation of test specimens, procedure) and test report.
|
Withdrawn |
1987-11 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 7390:2002 |
Building construction — Jointing products — Determination of resistance to flow of sealants |
This International Standard specifies a method for the determination of the resistance to flow of sealants, by loss of cohesion under their own weight. These sealants are used in joints in vertical surfaces in building construction.
|
Published |
2002-10 |
Edition : 3 |
Number of pages : 4 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 8339:1984 |
Building construction — Jointing products — Sealants — Determination of tensile properties |
Specifies a method for the determination of the tensile properties of sealants used in joints in building construction. The sealant to be tested adheres to two parallel contact surfaces of test specimens which are extended to rupture. The tensile properties are recorded on a force/strain diagram.
|
Withdrawn |
1984-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 8339:2005 |
Building construction — Sealants — Determination of tensile properties (Extension to break) |
ISO 8339:2005 specifies a method for the determination of the tensile properties of sealants used in joints in building construction.
|
Published |
2005-06 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 8340:1984 |
Building construction — Jointing products — Sealants — Determination of tensile properties at maintained extension |
Specifies a method for the determination of the tensile properties at maintained extension of sealants used in joints in building construction. The sealant to be tested adheres to two parallel contact surfaces of prepared test specimens which are extended to a defined width. The extension is maintained under defined conditions. Any breaks in adhesion or cohesion are recorded.
|
Withdrawn |
1984-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 8340:1984/Cor 1:1995 |
Building construction — Jointing products — Sealants — Determination of tensile properties at maintained extension — Technical Corrigendum 1 |
Amends the last sentence of clause 4 (Principle) and deletes the last two lines of clause 9 (Test report) and replaces them by new text.
|
Withdrawn |
1995-04 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
91.100.50
Binders. Sealing materials
|
| ISO 8394-2:2010 |
Building construction — Jointing products — Part 2: Determination of extrudability of sealants using standardized apparatus |
ISO 8394-2:2010 specifies a method for determining the extrudability of sealants independently of the package in which they are supplied. It is not applicable to the classification of sealants.
|
Withdrawn |
2010-10 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
91.100.50
Binders. Sealing materials
|