| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO 11298-1:2010 |
Plastics piping systems for renovation of underground water supply networks — Part 1: General |
ISO 11298-1:2010 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground water supply networks, which transport water intended for human consumption, including raw water intake pipelines. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is not applicable to cover sprayed coatings, the existing pipeline or any annular filler.
|
Withdrawn |
2010-03 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 2531:2009/Cor 1:2010 |
Ductile iron pipes, fittings, accessories and their joints for water applications — Technical Corrigendum 1 |
|
Published |
2010-11 |
Edition : 6 |
Number of pages : 3 |
Technical Committee |
77.140.75
Steel pipes and tubes for specific use
;
91.140.40
Gas supply systems
;
91.140.60
Water supply systems
|
| ISO 11298-1:2018 |
Plastics piping systems for renovation of underground water supply networks — Part 1: General |
ISO 11298-1:2018 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground water supply networks. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is not applicable to the existing pipeline or any non-structural sprayed coatings or annular filler.
ISO 11298-1:2018 gives the general requirements common to all relevant renovation techniques.
|
Published |
2018-03 |
Edition : 2 |
Number of pages : 16 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 11298-2:2018 |
Plastics piping systems for renovation of underground water supply networks — Part 2: Lining with continuous pipes |
ISO 11298-2:2018, read in conjunction with ISO 11298-1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground water supply networks. It is applicable to PE pipes of three different types:
- PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes;
- PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating;
- PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe ("coated pipe"); see Annex A.
In addition, ISO 11298-2:2018 covers
- jointing of pipe lengths by means of butt fusion, and
- fabricated and injection-moulded fittings made of PE.
ISO 11298-2:2018 is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature.
NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427-1:2007, Annex A.
|
Published |
2018-02 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 11298-3:2010 |
Plastics piping systems for renovation of underground water supply networks — Part 3: Lining with close-fit pipes |
ISO 11298-3:2010, in conjunction with ISO 11298-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines.
It is applicable to polyethylene (PE) pipe for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.
|
Withdrawn |
2010-03 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 11298-3:2018 |
Plastics piping systems for renovation of underground water supply networks — Part 3: Lining with close-fit pipes |
This document, in conjunction with ISO 11298‑1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines.
It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner, as well as associated fittings and joints for the construction of the lining system. It is not applicable to PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe.
It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature.
NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427‑1:2007, Annex A.
|
Published |
2018-08 |
Edition : 2 |
Number of pages : 16 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 11298-4:2021 |
Plastics piping systems for renovation of underground water supply networks — Part 4: Lining with cured-in-place pipes |
This document, in conjunction with ISO 11298‑1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines.
It applies to independent (fully structural, class A) and interactive (semi structural, class B) pressure pipe liners, as defined in ISO 11295, which do not rely on adhesion to the existing pipeline. It applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials, reinforcement, and other process-related plastics components (see 5.1).
It does not include requirements or test methods for resistance to cyclic loading or the pressure rating of CIPP liners where passing through bends, which are outside the scope of this document.
It is applicable to cured-in-place pipe lining systems intended to be used at a service temperature of up to 25 °C.
NOTE For applications operating at service temperatures greater than 25 °C, guidance on re-rating factors can be supplied by the system supplier.
|
Published |
2021-04 |
Edition : 1 |
Number of pages : 39 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 21004:2006 |
Plastics piping systems — Multilayer pipes and their joints, based on thermoplastics, for water supply |
ISO 21004:2006 specifies the general requirements and the performance requirements for multilayer pipes based on thermoplastics intended to be used for water supply outside buildings, for buried water mains and services and for water supplies above ground.
ISO 21004:2006 gives guidance for the design of piping systems consisting of multilayer pipes based on thermoplastics or, for which at least 60 % of the wall thickness is polymeric material, and the inner layer in contact with water is made of polymeric material.
The polymeric layers used for the stress-bearing layers are selected from polybutylene (PB), polyethylene (PE), crosslinked polyethylene (PE-X), polypropylene (PP), chlorinated poly(vinyl chloride) (PVC-C) and unplasticized poly(vinyl chloride) (PVC-U).
ISO 21004:2006 is applicable to piping systems used for the conveyance under pressure of cold water (up to approximately 20 °C) for drinking. It is also applicable to piping systems for the conveyance of water (up to and including 40 °C) for general purposes.
|
Published |
2006-11 |
Edition : 1 |
Number of pages : 25 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 21307:2009 |
Plastics pipes and fittings — Butt fusion jointing procedures for polyethylene (PE) pipes and fittings used in the construction of gas and water distribution systems |
ISO 21307:2009 establishes general principles for the process used in the construction and quality assessment of butt fusion joints incorporating fittings (ISO 8085-2) and pipes used in the construction of gas (ISO 4437) and water (ISO 4427) distribution systems, made from PE 80 and PE 100 materials having a melt flow rate at 190 °C/5 g of between 0,3 g/10 min and 1,7 g/10 min, with equipment which complies with ISO 12176-1 and installed in accordance with ISO/TS 10839.
Also specified are a number of proven butt fusion jointing procedures for pipes and fittings with a wall thickness up to and including 70 mm, the materials and components used, the fusion jointing procedure and equipment, and the quality assessment of the completed joint.
|
Withdrawn |
2009-01 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
75.200
Petroleum products and natural gas handling equipment
;
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 21307:2011 |
Plastics pipes and fittings — Butt fusion jointing procedures for polyethylene (PE) pipes and fittings used in the construction of gas and water distribution systems |
ISO 21307:2011 establishes general principles regarding the procedure used in the construction and quality assessment of butt fusion joints incorporating fittings (ISO 8085-2) and pipes used in the construction of gas (ISO 4437) and water (ISO 4427) distribution systems made with equipment that complies with ISO 12176-1 and installed in accordance with ISO/TS 10839, relevant codes of practice, national regulations or industry guidance. Specifically, ISO 21307:2011 specifies a number of proven butt fusion jointing procedures for pipes and fittings with a wall thickness up to and including 70 mm. ISO 21307:2011 takes into consideration the materials and components used, the fusion jointing procedure and equipment and the quality assessment of the completed joint. It can be applied in conjunction with appropriate national regulations and standards.
|
Withdrawn |
2011-05 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
75.200
Petroleum products and natural gas handling equipment
;
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 21307:2017 |
Plastics pipes and fittings — Butt fusion jointing procedures for polyethylene (PE) piping systems |
ISO 21307:2017 establishes general principles regarding the procedure used in the construction and quality assessment of butt fusion jointing of polyethylene (PE) piping system components specified in accordance with relevant ISO standards. These components are installed in accordance with the relevant codes of practice, national regulations or industry guidance. Specifically, this document specifies three butt fusion jointing procedures for PE pipes and fittings. These are:
- single low-pressure fusion jointing procedure;
- dual low-pressure fusion jointing procedure;
- single high-pressure fusion jointing procedure.
ISO 21307:2017 takes into consideration the materials and components used, the fusion jointing procedure and equipment and the quality assessment of the completed joint. It can be applied in conjunction with appropriate national regulations and standards.
|
Published |
2017-12 |
Edition : 3 |
Number of pages : 16 |
Technical Committee |
75.200
Petroleum products and natural gas handling equipment
;
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 21307:2017/Amd 1:2020 |
Plastics pipes and fittings — Butt fusion jointing procedures for polyethylene (PE) piping systems — Amendment 1 |
|
Published |
2020-01 |
Edition : 3 |
Number of pages : 2 |
Technical Committee |
75.200
Petroleum products and natural gas handling equipment
;
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 4064-2:1978/Add 1:1983 |
Measurement of water flow in closed conduits — Meters for cold potable water — Part 2: Installation requirements — Addendum 1: Parallel and multiple meter operation |
|
Withdrawn |
1983-09 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 22391-1:2007 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 1: General |
ISO 22391-1:2007 specifies the general aspects of piping systems made of polyethylene of raised temperature resistance (PE-RT), intended to be used for hot and cold water installations within buildings for the conveyance of water -- whether or not the water is intended for human consumption (domestic systems) or heating systems -- under specified design pressures and temperatures according to the class of application.
It covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and defines terms, symbols and abbreviated terms for the whole of ISO 22391. When used in conjunction with the other parts of ISO 22391, it is respectively applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT as well as of other plastics and non-plastics materials, used for hot and cold water installations.
It is not applicable for values of design temperature, maximum design temperature or malfunction temperature in excess of those it specifies.
|
Withdrawn |
2007-01 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO 22391-1:2009 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 1: General |
ISO 22391-1:2009 specifies the general characteristics of piping systems made of polyethylene of raised temperature resistance (PE‑RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under specified design pressures and temperatures appropriate to the class of application.
ISO 22391-1:2009 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and defines terms. In conjunction with the other parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints and to joints having components of PE-RT, as well as of other plastics and non-plastics materials, respectively, used for hot and cold water installations.
|
Published |
2009-12 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO 22391-2:2007 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 2: Pipes |
This part of ISO 22391 specifies the characteristics of pipe made from polyethylene of raised temperature resistance (PE-RT), intended to be used for hot and cold water installations within buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or heating systems — under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
It covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. When used in conjunction with the other parts of ISO 22391, it is respectively applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT as well as of other plastics and non-plastics materials, used for hot and cold water installations.
It is applicable to pipes with or without a barrier layer or layers.
It is not applicable for values of design temperature, maximum design temperature or malfunction temperature in excess of those specified in ISO 22391-1.
NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
|
Withdrawn |
2007-01 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 22391-2:2009 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 2: Pipes |
ISO 22391-2:2009 specifies the characteristics of pipe made of polyethylene of raised temperature resistance (PE-RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
ISO 22391-2:2009 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. When used in conjunction with the other parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT, as well as of other plastics and non-plastics materials, respectively, used for hot and cold water installations.
It is applicable to pipes with or without a barrier layer or layers.
|
Published |
2009-12 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 22391-2:2009/Amd 1:2020 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 2: Pipes — Amendment 1 |
|
Published |
2020-11 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 4064-2:2001 |
Measurement of water flow in closed conduits — Meters for cold potable water — Part 2: Installation requirements and selection |
|
Withdrawn |
2001-06 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 22391-3:2007 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 3: Fittings |
ISO 22391-3:2007 specifies the characteristics of fittings for piping systems made from polyethylene of raised temperature resistance (PE-RT), intended to be used for hot and cold water installations within buildings for the conveyance of water -- whether or not the water is intended for human consumption (domestic systems) or heating systems -- under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
It covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. When used in conjunction with the other parts of ISO 22391, it is applicable to fittings made from PE-RT, as well as to those made from other materials, intended to be fitted to pipes conforming to ISO 22391-2 for hot and cold water installations, the joints of which are in accordance with ISO 22391-5.
ISO 22391-3:2006 is applicable to the following types of fitting: mechanical fittings; socket fusion fitting; electrofusion fittings; fittings with incorporated inserts.
It is not applicable for values of design temperature, maximum design temperature or malfunction temperature in excess of those specified in ISO 22391-1.
|
Withdrawn |
2007-01 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 22391-3:2009 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 3: Fittings |
ISO 22391-3:2009 specifies the characteristics of fittings for piping systems made of polyethylene of raised temperature resistance (PE-RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
ISO 22391-3:2009 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. In conjunction with the other parts of ISO 22391, it is applicable to fittings made of PE-RT, as well as to those made of other materials, intended to be fitted to pipes conforming to ISO 22391-2 for hot and cold water installations, the joints of which are in accordance with ISO 22391-5.
It is applicable to the following types of fitting:
- mechanical fittings;
- socket fusion fitting;
- electrofusion fittings;
- fittings with incorporated inserts.
|
Published |
2009-12 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 22391-3:2009/Amd 1:2020 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 3: Fittings — Amendment 1 |
|
Published |
2020-12 |
Edition : 2 |
Number of pages : 1 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 22391-3:2009/Amd 2:2021 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 3: Fittings — Amendment 2 |
|
Published |
2021-10 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 22391-5:2007 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 5: Fitness for purpose of the system |
ISO 22391-5:2007 specifies the characteristics of the fitness for purpose of piping systems made from polyethylene of raised temperature resistance (PE-RT), intended to be used for hot and cold water installations within buildings for the conveyance of water -- whether or not the water is intended for human consumption (domestic systems) or heating systems -- under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
It covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. When used in conjunction with the other parts of ISO 22391, it is respectively applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT as well as of other plastics and non-plastics materials, used for hot and cold water installations.
It is not applicable for values of design temperature, maximum design temperature or malfunction temperature in excess of those specified in ISO 22391-1.
|
Withdrawn |
2007-01 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO 8795:1998 |
Plastics piping systems for the conveyance of water intended for human consumption — Migration assessment — Determination of migration values for plastics pipes |
|
Withdrawn |
1998-04 |
Edition : 2 |
Number of pages : 16 |
Technical Committee |
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 22391-5:2009 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 5: Fitness for purpose of the system |
ISO 22391-5:2009 specifies the characteristics of the fitness for purpose of piping systems made of polyethylene of raised temperature resistance (PE-RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
ISO 22391-5:2009 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. In conjunction with the other parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT as well as of other plastics and non-plastics materials, respectively, used for hot and cold water installations.
|
Published |
2009-12 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO 22391-5:2009/Amd 1:2020 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 5: Fitness for purpose of the system — Amendment 1 |
|
Published |
2020-12 |
Edition : 2 |
Number of pages : 3 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO/TS 22391-7:2011 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 7: Guidance for the assessment of conformity |
ISO/TS 22391-7:2011 gives guidance on the assessment of conformity of products and assemblies in accordance with other applicable part(s) of ISO 22391 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of third-party certification procedures.
In conjunction with the other parts, ISO/TS 22391-7:2011 is applicable to hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems), under design pressures and temperatures appropriate to the class of application.
|
Withdrawn |
2011-11 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO/TS 22391-7:2018 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 7: Guidance for the assessment of conformity |
This document gives requirements and guidance for the assessment of conformity of materials, products, and assemblies in accordance with the applicable part(s) of ISO 22391 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with the other parts of ISO 22391 (see Foreword), this document is applicable to polyethylene of raised temperature resistance (PE-RT) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see ISO 22391-1:2009, Table 1).
|
Published |
2018-11 |
Edition : 2 |
Number of pages : 16 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO 24512:2007 |
Activities relating to drinking water and wastewater services — Guidelines for the management of drinking water utilities and for the assessment of drinking water services |
ISO 24512:2007 provides guidelines for the management of drinking water utilities and for the assessment of drinking water services.
ISO 24512:2007 is applicable to publicly and privately owned and operated water utilities. It does not favour any particular ownership or operating model.
ISO 24512:2007 addresses drinking water systems in their entirety and is applicable to systems at any level of development (e.g. on-site systems, distribution networks, treatment facilities).
The following are within the scope of ISO 24512:2007:
the definition of a language common to different stakeholders;
the definition of the components of drinking water supply systems;
guidelines for the management of drinking water utilities;
guidelines for objectives, service assessment criteria and related performance indicators, appropriate for the assessment of drinking water services.
|
Published |
2007-12 |
Edition : 1 |
Number of pages : 54 |
Technical Committee |
93.025
External water conveyance systems
;
13.060.20
Drinking water
|
| ISO/DIS 24512 |
Activities relating to drinking water and wastewater services — Guidelines for the management of drinking water utilities and for the assessment of drinking water services |
|
Under development |
|
Edition : 2 |
Number of pages : 53 |
Technical Committee |
93.025
External water conveyance systems
;
03.080.30
Services for consumers
;
13.060.20
Drinking water
|
| ISO 24536:2019 |
Service activities relating to drinking water supply, wastewater and stormwater systems — Stormwater management — Guidelines for stormwater management in urban areas |
This document provides guidance to stormwater management authorities and relevant stakeholders on both structural and non-structural stormwater management approaches. The guidance includes consideration of relevant policies, planning, design criteria and implementation processes for stormwater management, and performance evaluation. This document can be applied to new stormwater systems and to the extension or improvement of existing systems for both fully separated and combined storm and sanitary sewers.
This document is applicable to stormwater sewer systems as well as combined sewer systems.
This document is not applicable to sanitary sewer systems.
|
Published |
2019-10 |
Edition : 1 |
Number of pages : 54 |
Technical Committee |
93.025
External water conveyance systems
;
03.080.30
Services for consumers
;
13.060.01
Water quality in general
|
| ISO/TR 24539:2021 |
Service activities relating to drinking water supply, wastewater and stormwater systems — Examples of good practices for stormwater management |
This document provides examples of good practices in stormwater management related to ISO 24536 and information on standards and guidelines used in various countries.
|
Published |
2021-04 |
Edition : 1 |
Number of pages : 80 |
Technical Committee |
93.025
External water conveyance systems
;
03.080.30
Services for consumers
;
13.060.01
Water quality in general
|
| ISO 559:1977 |
Welded or seamless steel tubes for water, sewage and gas |
|
Withdrawn |
1977-04 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
77.140.75
Steel pipes and tubes for specific use
;
91.140.40
Gas supply systems
;
91.140.60
Water supply systems
;
91.140.80
Drainage systems
|
| ISO 559:1991 |
Steel tubes for water and sewage |
This second edition cancels and replaces the first edition (ISO 559:1977). Specifies the technical conditions for delivery of seamless and welded steel tubes for the conveyance of water and sewage at temperatures between - 10 °C and 120 °C. Does not apply to steel tubes in accordance with ISO 65 and similar plain end tubes. Contains references, definitions, informations to be supplied by the purchaser, and data relating to manufacturing process, chemical composition, mechanical properties and weldability, dimensions, masses and tolerances, appearance and soundness, inspection and testing, marking, lining or coating and documents.
|
Withdrawn |
1991-03 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
93.025
External water conveyance systems
;
77.140.75
Steel pipes and tubes for specific use
;
91.140.60
Water supply systems
;
91.140.80
Drainage systems
|
| ISO 1452-1:2009 |
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: General |
ISO 1452-1:2009 specifies the general aspects of unplasticized poly(vinyl chloride) (PVC‑U) solid-wall piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure.
In conjunction with ISO 1452-2, ISO 1452-3, ISO 1452-4 and ISO 1452-5, it is applicable to PVC‑U pipes, fittings, valves and ancillary equipment, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in the ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above ground drainage and sewerage under pressure.
It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to components for the conveyance of water and waste water up to and including 45 °C.
|
Published |
2009-12 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 1452-2:2009 |
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 2: Pipes |
ISO 1452-2:2009 specifies the characteristics of solid-wall pipes made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1 and ISO 1452-5, it is applicable to extruded PVC‑U pipes without a socket and pipes with a socket (integral or not), intended to be used for the following:
- water mains and services buried in the ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above ground drainage and sewerage under pressure.
It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to pipes for the conveyance of water and waste water up to and including 45 °C and to a range of pipe sizes and pressure classes. It gives requirements concerning colours.
|
Published |
2009-12 |
Edition : 1 |
Number of pages : 23 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 1452-3:2009 |
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 3: Fittings |
ISO 1452-3:2009 specifies the characteristics of fittings made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2 and ISO 1452-5, it is applicable to PVC‑U fittings and to joints with components of PVC‑U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in the ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above ground drainage and sewerage under pressure.
It is applicable to fittings in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to components for the conveyance of water and waste water up to and including 45 °C.
|
Published |
2009-12 |
Edition : 1 |
Number of pages : 37 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 1452-4:2009 |
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 4: Valves |
ISO 1452-4:2009 specifies the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-5 it is applicable to PVC‑U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above-ground drainage and sewerage under pressure.
It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to valves for the conveyance of water and waste water up to and including 45 °C.
|
Published |
2009-12 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 1452-5:2009 |
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 5: Fitness for purpose of the system |
ISO 1452-5:2009 specifies the characteristics for the fitness for purpose of unplasticized poly(vinyl chloride) (PVC‑U) piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-4, it is applicable to joints and assemblies with components of PVC‑U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above-ground drainage and sewerage under pressure;
It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to components for the conveyance of water and waste water up to and including 45 °C.
|
Published |
2009-12 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 2531:1998 |
Ductile iron pipes, fittings, accessories and their joints for water or gas applications |
|
Withdrawn |
1998-08 |
Edition : 5 |
Number of pages : 46 |
Technical Committee |
77.140.75
Steel pipes and tubes for specific use
;
91.140.40
Gas supply systems
;
91.140.60
Water supply systems
|
| ISO 2531:2009 |
Ductile iron pipes, fittings, accessories and their joints for water applications |
ISO 2531:2009 specifies the requirements and test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of pipelines:
- to convey water (e.g. for human consumption and raw water),
- operated with or without pressure, and
- installed below or above ground.
It specifies materials, dimensions and tolerances, mechanical properties and standard coatings of pipes, fittings and accessories. It also gives performance requirements for all components including joints.
ISO 2531:2009 applies to pipes, fittings and accessories cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints in the size range DN 40 to DN 2600 inclusive.
|
Published |
2009-12 |
Edition : 6 |
Number of pages : 73 |
Technical Committee |
77.140.75
Steel pipes and tubes for specific use
;
91.140.40
Gas supply systems
;
91.140.60
Water supply systems
|
| ISO 3114:1977 |
Unplasticized polyvinyl chloride (PVC) pipes for potable water supply — Extractability of lead and tin — Test method |
Specifies a method of test for the determination of the extractability of certain stabilizers of unplasticized PVC in order to verify that the extracted quantities do not exceed a certain concentration. Tubular test pieces are prewashed during a fixed time. After this they are extracted with acidified (CO2) water in three steps and the quantity of the extracted stabilizers (lead salts or organic derivates to tin) shall be determined. The analytic methods are not specified.
|
Published |
1977-03 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 3822-1:1983 |
Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 1: Method of measurement |
|
Withdrawn |
1983-12 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
17.140.20
Noise emitted by machines and equipment
;
91.140.60
Water supply systems
|
| ISO 3822-1:1999 |
Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 1: Method of measurement |
|
Published |
1999-05 |
Edition : 3 |
Number of pages : 20 |
Technical Committee |
17.140.20
Noise emitted by machines and equipment
;
91.140.60
Water supply systems
|
| ISO 3822-1:1999/Amd 1:2008 |
Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 1: Method of measurement — Amendment 1: Measurement uncertainty |
|
Published |
2008-12 |
Edition : 3 |
Number of pages : 3 |
Technical Committee |
17.140.20
Noise emitted by machines and equipment
;
91.140.60
Water supply systems
|
| ISO 3822-2:1984 |
Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 2: Mounting and operating conditions for draw-off taps |
|
Withdrawn |
1984-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
17.140.20
Noise emitted by machines and equipment
;
91.140.60
Water supply systems
|
| ISO 3822-2:1995 |
Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 2: Mounting and operating conditions for draw-off taps and mixing valves |
Describes the mounting and operating conditions to be used for draw-off taps and mixing valves when measuring noise emmission resulting from water flow. Replaces the first edition, which has been technically revised.
|
Published |
1995-12 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
17.140.20
Noise emitted by machines and equipment
;
91.140.60
Water supply systems
|
| ISO 3822-3:1984 |
Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 3: Mounting and operating conditions for in-line valves and appliances |
|
Withdrawn |
1984-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
17.140.20
Noise emitted by machines and equipment
;
91.140.60
Water supply systems
|
| ISO 3822-3:1997 |
Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 3: Mounting and operating conditions for in-line valves and appliances |
Gives the mounting and operating conditions to be used for in-line valves and appliances, which control the flow, pressure or temperature of the water in water supply installations, when measuring the noise emission resulting from water flow. Replaces the first edition.
|
Withdrawn |
1997-02 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
17.140.20
Noise emitted by machines and equipment
;
91.140.60
Water supply systems
|
| ISO 3822-3:1997/Amd 1:2009 |
Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 3: Mounting and operating conditions for in-line valves and appliances — Amendment 1 |
|
Withdrawn |
2009-11 |
Edition : 2 |
Number of pages : 1 |
Technical Committee |
17.140.20
Noise emitted by machines and equipment
;
91.140.60
Water supply systems
|
| ISO 4064-2:2005 |
Measurement of water flow in fully charged closed conduits — Meters for cold potable water and hot water — Part 2: Installation requirements |
ISO 4064-2:2005 specifies criteria for the selection of single, combination and concentric water meters, associated fittings, installation, special requirements for meters and the first operation of new or repaired meters to ensure accurate constant measurement and reliable reading of the meter.
ISO 4064-2:2005 also applies to water meters, based on electrical or electronic principles and to water meters based on mechanical principles incorporating electronic devices, used to meter the actual volume flow of cold potable water. It also applies to electronic ancillary devices.
The recommendations of this ISO 4064-2:2005 apply to water meters, irrespective of technology, defined as integrating measuring instruments continuously determining the volume of water flowing through them.
|
Withdrawn |
2005-10 |
Edition : 3 |
Number of pages : 10 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 3822-3:2018 |
Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 3: Mounting and operating conditions for in-line valves and appliances |
ISO 3822-3:2018 specifies the mounting and operating conditions to be used for in-line valves and appliances which control the flow, pressure or temperature of the water in water supply installations, when measuring noise emission resulting from water flow.
ISO 3822-3:2018 is applicable to in-line valves and appliances of maximum nominal size DN 32 and to systems in which the maximum water flow rate does not exceed 1,6 l/s.
NOTE See ISO 6708; DN is the symbol for "nominal size". The number of the nominal size is loosely related to the inside diameter (in millimetres) of the in-tine valves and appliances.
The procedures described are for general use for all types of in-line valves of conventional design.
|
Published |
2018-01 |
Edition : 3 |
Number of pages : 8 |
Technical Committee |
17.140.20
Noise emitted by machines and equipment
;
91.140.60
Water supply systems
|
| ISO 3822-4:1985 |
Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 4: Mounting and operating conditions for special appliances |
|
Withdrawn |
1985-10 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
17.140.20
Noise emitted by machines and equipment
;
91.140.60
Water supply systems
|
| ISO 3822-4:1997 |
Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 4: Mounting and operating conditions for special appliances |
Gives the mounting and operating conditions to be used for a number of in-line valves and appliances, when measuring the noise emission resulting from water flow. Replaces the first edition.
|
Published |
1997-02 |
Edition : 2 |
Number of pages : 24 |
Technical Committee |
17.140.20
Noise emitted by machines and equipment
;
91.140.60
Water supply systems
|
| ISO 4064-1:1977 |
Measurement of water flow in closed conduits — Meters for cold potable water — Part 1: Specification |
|
Withdrawn |
1977-12 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 4064-1:1993 |
Measurement of water flow in closed conduits — Meters for cold potable water — Part 1: Specifications |
Deals with terminology, technical characteristics, metrological characteristics and pressure loss. Applies to water meters of various metrological classes which can withstand permanent flow-rates from 0,6 m^3/h to 4000 m^3/h, maximum admissible working pressures equal to or greater than 10 bar and a maximum admissible temperature of 30 °C. Legal requirements take precedence over the recommendations of this part.
|
Withdrawn |
1993-05 |
Edition : 2 |
Number of pages : 10 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 4064-1:2005 |
Measurement of water flow in fully charged closed conduits — Meters for cold potable water and hot water — Part 1: Specifications |
ISO 4064-1:2005 specifies terminology, technical characteristics, metrological characteristics and pressure loss requirements for cold potable water and hot water meters. It applies to water meters that can withstand maximum admissible working pressures (MAP) at least 1 MPa (0,6 MPa for meters for use with pipe nominal diameters, DN at least 500 mm) and a maximum admissible temperature, MAT, for cold potable water meters of 30 ºC and for hot water meters up to 180 ºC, depending on class.
ISO 4064-1:2005 also applies to water meters, based on electrical or electronic principles and to water meters based on mechanical principles incorporating electronic devices, used to meter the actual volume flow of cold potable water and hot water. It also applies to electronic ancillary devices. Generally ancillary devices are optional.
The specifications of ISO 4064-1:2005 apply to water meters, irrespective of technology, defined as integrating measuring instruments continuously determining the volume of water flowing through them.
|
Withdrawn |
2005-10 |
Edition : 3 |
Number of pages : 42 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 4064-1:2014 |
Water meters for cold potable water and hot water — Part 1: Metrological and technical requirements |
ISO 4064-1:2014|OIML R 49-1:2013 specifies metrological and technical requirements of water meters for cold potable water and hot water flowing through a fully charged, closed conduit. These water meters incorporate devices which indicate the integrated volume.
In addition to water meters based on mechanical principles, ISO 4064-1:2014|OIML R 49-1:2013 applies to devices based on electrical or electronic principles, and mechanical principles incorporating electronic devices, used to measure the volume of cold potable water and hot water.
ISO 4064-1:2014|OIML R 49-1:2013 also applies to electronic ancillary devices. Ancillary devices are optional. However, it is possible for national or regional regulations to make some ancillary devices mandatory in relation to the utilization of water meters.
|
Published |
2014-06 |
Edition : 4 |
Number of pages : 38 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO/CD 4064-1 |
Water meters for cold potable water and hot water — Part 1: Metrological and technical requirements |
|
Under development |
|
Edition : 5 |
|
Technical Committee |
91.140.60
Water supply systems
|
| ISO 4064-2:1978 |
Measurement of water flow in closed conduits — Meters for cold potable water — Part 2: Installation requirements |
|
Withdrawn |
1978-12 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 4064-2:2014 |
Water meters for cold potable water and hot water — Part 2: Test methods |
ISO 4064-2:2014|OIML R 49-2:2013 is applicable to the type evaluation and initial verification testing of water meters for cold potable water and hot water as defined in ISO 4064‑1:2014|OIML R 49‑1:2013. OIML Certificates of Conformity can be issued for water meters under the scope of the OIML Certificate System, provided that ISO 4064-2:2014|OIML R 49-2:2013, ISO 4064‑1:2014|OIML R 49‑1:2013 and ISO 4064‑3:2014|OIML R 49‑3:2013 are used in accordance with the rules of the system.
ISO 4064-2:2014|OIML R 49-2:2013 sets out details of the test programme, principles, equipment and procedures to be used for the type evaluation, and initial verification of a meter type.
The provisions of ISO 4064-2:2014|OIML R 49-2:2013 also apply to ancillary devices, if required by national regulations.
The provisions include requirements for testing the complete water meter and for testing the measurement transducer (including the flow or volume sensor) and the calculator (including the indicating device) of a water meter as separate units.
|
Published |
2014-06 |
Edition : 4 |
Number of pages : 101 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO/CD 4064-2 |
Water meters for cold potable water and hot water — Part 2: Test methods |
|
Under development |
|
Edition : 5 |
|
Technical Committee |
91.140.60
Water supply systems
|
| ISO 4064-3:1983 |
Measurement of water flow in closed conduits — Meters for cold potable water — Part 3: Test methods and equipment |
|
Withdrawn |
1983-09 |
Edition : 1 |
Number of pages : 16 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 4064-3:1999 |
Measurement of water flow in closed conduits — Meters for cold potable water — Part 3: Test methods and equipment |
|
Withdrawn |
1999-05 |
Edition : 2 |
Number of pages : 24 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 4064-3:2005 |
Measurement of water flow in fully charged closed conduits — Meters for cold potable water and hot water — Part 3: Test methods and equipment |
ISO 4064-3:2005 specifies the test methods and means to be employed in determining the principal characteristics of water meters.
ISO 4064-3:2005 is applicable to cold potable water and hot water concentric and combination meters, which can withstand maximum admissible working pressures equal to at least 1 MPa (10 bar) (0,6 MPa (6 bar) for meters greater than DN 500 and a maximum admissible temperature for cold potable water meters of 30 °C and for hot water meters of up to 180 °C, depending on the class.
ISO 4064-3:2005 also applies to water meters based on electrical or electronic principles and to water meters based on mechanical principles incorporating electrical devices, used to meter the actual volume flow of cold potable water and hot water.
|
Withdrawn |
2005-10 |
Edition : 3 |
Number of pages : 71 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 4064-3:2014 |
Water meters for cold potable water and hot water — Part 3: Test report format |
ISO 4064-3:2014|OIML R 49-3:2013 specifies a test report format to be used in conjunction with ISO 4064-1:2014|OIML R 49-1:2013 and ISO 4064-2:2014|OIML R 49-2:2013 for water meters for cold potable water and hot water.
|
Published |
2014-06 |
Edition : 4 |
Number of pages : 71 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO/CD 4064-3 |
Water meters for cold potable water and hot water — Part 3: Test report format |
ISO 4064-3:2014|OIML R 49-3:2013 specifies a test report format to be used in conjunction with ISO 4064-1:2014|OIML R 49-1:2013 and ISO 4064-2:2014|OIML R 49-2:2013 for water meters for cold potable water and hot water.
|
Under development |
|
Edition : 5 |
|
Technical Committee |
91.140.60
Water supply systems
|
| ISO 4064-4:2014 |
Water meters for cold potable water and hot water — Part 4: Non-metrological requirements not covered in ISO 4064-1 |
ISO 4064-4:2014 applies to water meters used to meter the volume of cold potable water and hot water flowing through a fully charged, closed conduit. These water meters incorporate devices which indicate the integrated volume.
ISO 4064-4:2014 specifies technical characteristics and pressure loss requirements for meters for cold potable water and hot water. It applies to water meters which can withstand: a) a maximum admissible working pressure (MAP) equal to at least 1 MPa [0,6 MPa for meters for use with pipe nominal diameters (DNs) ≥500 mm]; b) a maximum admissible temperature (MAT) for cold potable water meters of 30 °C; c) a MAT for hot water meters up to 180 °C, depending on class.
In addition to meters based on mechanical principles, ISO 4064-4:2014 also applies to water meters based on electrical or electronic principles, and to water meters based on mechanical principles incorporating electronic devices, used to meter the volume flow of hot water and cold potable water. It also applies to electronic ancillary devices. As a rule ancillary devices are optional. However, national or international regulations may make some ancillary devices mandatory in relation to the utilization of the water meter.
|
Published |
2014-06 |
Edition : 1 |
Number of pages : 26 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 6992:1986 |
Unplasticized polyvinyl chloride (PVC-U) pipes for drinking water supply — Extractability of cadmium and mercury occurring as impurities |
Specification of the procedure of pipe sample extraction with carbondioxide water in three steps of extraction. The quantities of cadmium and mercury in the water extracts shall be determined, but the analytical methods for these determinations are not defined.
|
Withdrawn |
1986-07 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO/CD 4064-4 |
Water meters for cold potable water and hot water — Part 4: Non-metrological requirements not covered in ISO 4064-1 |
ISO 4064-4:2014 applies to water meters used to meter the volume of cold potable water and hot water flowing through a fully charged, closed conduit. These water meters incorporate devices which indicate the integrated volume.
ISO 4064-4:2014 specifies technical characteristics and pressure loss requirements for meters for cold potable water and hot water. It applies to water meters which can withstand: a) a maximum admissible working pressure (MAP) equal to at least 1 MPa [0,6 MPa for meters for use with pipe nominal diameters (DNs) ≥500 mm]; b) a maximum admissible temperature (MAT) for cold potable water meters of 30 °C; c) a MAT for hot water meters up to 180 °C, depending on class.
In addition to meters based on mechanical principles, ISO 4064-4:2014 also applies to water meters based on electrical or electronic principles, and to water meters based on mechanical principles incorporating electronic devices, used to meter the volume flow of hot water and cold potable water. It also applies to electronic ancillary devices. As a rule ancillary devices are optional. However, national or international regulations may make some ancillary devices mandatory in relation to the utilization of the water meter.
|
Under development |
|
Edition : 2 |
|
Technical Committee |
91.140.60
Water supply systems
|
| ISO 4064-5:2014 |
Water meters for cold potable water and hot water — Part 5: Installation requirements |
ISO 4064-5:2014 applies to water meters used to meter the volume of cold potable water and hot water flowing through a fully charged, closed conduit. These water meters incorporate devices which indicate the integrated volume.
ISO 4064-5:2014 specifies criteria for the selection of single, combination and concentric water meters, associated fittings, installation, special requirements for meters, and the first operation of new or repaired meters to ensure accurate constant measurement and reliable reading of the meter.
In addition to meters based on mechanical principles, ISO 4064-5:2014 also applies to water meters based on electrical or electronic principles, and to water meters based on mechanical principles incorporating electronic devices, used to measure the volume of cold potable water and hot water. It also applies to electronic ancillary devices. Ancillary devices are optional. However, national or international regulations may make some ancillary devices mandatory in relation to the utilization of the water meter.
The recommendations of ISO 4064-5:2014 apply to water meters, irrespective of technology, defined as integrating measuring instruments continuously determining the volume of water flowing through them.
|
Published |
2014-06 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO/CD 4064-5 |
Water meters for cold potable water and hot water — Part 5: Installation requirements |
ISO 4064-5:2014 applies to water meters used to meter the volume of cold potable water and hot water flowing through a fully charged, closed conduit. These water meters incorporate devices which indicate the integrated volume.
ISO 4064-5:2014 specifies criteria for the selection of single, combination and concentric water meters, associated fittings, installation, special requirements for meters, and the first operation of new or repaired meters to ensure accurate constant measurement and reliable reading of the meter.
In addition to meters based on mechanical principles, ISO 4064-5:2014 also applies to water meters based on electrical or electronic principles, and to water meters based on mechanical principles incorporating electronic devices, used to measure the volume of cold potable water and hot water. It also applies to electronic ancillary devices. Ancillary devices are optional. However, national or international regulations may make some ancillary devices mandatory in relation to the utilization of the water meter.
The recommendations of ISO 4064-5:2014 apply to water meters, irrespective of technology, defined as integrating measuring instruments continuously determining the volume of water flowing through them.
|
Under development |
|
Edition : 2 |
|
Technical Committee |
91.140.60
Water supply systems
|
| ISO/TR 4191:1989 |
Unplasticized polyvinyl chloride (PVC-U) pipes for water supply — Recommended practice for laying |
|
Withdrawn |
1989-11 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO/TR 4191:2014 |
Plastics piping systems for water supply — Unplasticized poly(vinyl chloride)(PVC-U) and oriented PVC-U (PVC-O) — Guidance for installation |
ISO/TR 4191:2014 gives recommended practices for installation of unplasticized poly(vinyl chloride) (PVC-U) and oriented unplasticized poly(vinyl chloride) (PVC-O) pipes, fittings, valves, and ancillaries when used in piping systems conveying water under pressure.
The recommendations are intended to give practical guidance of design and installation of piping systems incorporating pipes, fittings, valves, and ancillary equipment made from PVC materials and used for the following purposes: water mains and services buried in ground, waste water under pressure, and conveyance of water above ground for both outside and inside buildings, for the supply of water under pressure at approximately 20 °C (cold water) intended for human consumption and for general purposes.
ISO/TR 4191:2014 is also applicable to components for the conveyance of water up to and including 45 °C. For temperatures between 25 °C and 45 °C, Figure 1 of ISO 1452‑2:2009 applies.
In addition, recommendations are given for the connection to fittings, valves, and ancillary equipment made from materials other than PVC.
|
Published |
2014-01 |
Edition : 2 |
Number of pages : 44 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 10639:2017 |
Plastics piping systems for pressure and non-pressure water supply — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
ISO 10639:2017 specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of water supply with or without pressure, including, but not limited to, raw water, irrigation, cooling water, potable water, salt water, sea water, penstocks in power plants, processing plants and other water-based applications. ISO 10639:2017 is applicable to GRP UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in direct buried installations.
NOTE 1 For the purpose of ISO 10639:2017, the term polyester resin (UP) also includes vinyl-ester resins (VE).
NOTE 2 Piping systems conforming to ISO 10639:2017 can also be used for non-buried applications, provided the influence of the environment and the supports are considered in the design of the pipes, fittings and joints.
NOTE 3 ISO 10639:2017t can also apply for other installations, such as slip-lining rehabilitation of existing pipes.
NOTE 4 ISO 10639:2017 is also referenced in ISO 25780, which specifies requirements for GRP-pipes used for jacking installation.
The requirements for the hydrostatic pressure design of pipes referring to ISO 10639:2017 meet the requirements of ISO/TS 20656‑1 and the general principle for the reliability of structures detailed in ISO 2394 and in EN 1990. These International Standards provide procedures for the harmonization of design practices and address the probability of failure, as well as possible consequences of failures. The design practices are based on a partial safety factor concept, as well as on risk management engineering.
ISO 10639:2017 is applicable to pipes, fittings and their joints of nominal sizes from DN 50 to DN 4000 which are intended to be used for the conveyance of water at temperatures up to 50 °C, with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together. Clause 4 specifies the general aspects of GRP UP piping systems intended to be used in the field of water supply with or without pressure.
Clause 5 specifies the characteristics of pipes made from GRP UP with or without aggregates and/or fillers. The pipes may have a thermoplastics or thermosetting resin liner. Clause 5 also specifies the test parameters for the test methods referred to in ISO 10639:2017.
Clause 6 specifies the characteristics of fittings made from GRP UP, with or without a thermoplastics or thermosetting resin liner, intended to be used for conveyance of water. Clause 6 specifies the dimensional and performance requirements for bends, branches, reducers, saddles and flanged adaptors. Clause 6 covers requirements to prove the structural design of fittings. It is applicable to fittings made using any of the following techniques:
- fabrication from straight pipes;
- moulding by
filament winding,
tape winding,
contact moulding, and
hot or cold compression moulding.
Clause 7 is applicable to the joints to be used in GRP UP piping systems to be used for the conveyance of water, both buried and non-buried. It covers requirements to prove the design of the joint. Clause 7 specifies type test performance requirements for the following joints as a function of the declared nominal pressure rating of the pipeline or system:
a) socket-and-spigot (including double-socket) joints or mechanical joints;
b) locked socket-and-spigot joints;
c) cemented or wrapped joints;
d) bolted flange joints.
|
Withdrawn |
2017-10 |
Edition : 2 |
Number of pages : 57 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO/TR 4340:2022 |
Water aggressiveness evaluation and optimized lining choice |
This document provides details about the aggressiveness factors, evaluation indicators of raw water, or inlet water of ductile iron pipe system and relevant lining information applicable to ductile iron pipes, fittings and accessories used in water mains and distribution system.
This document is intended to serve as a tool for estimating the properties of certain water and their effect on internal linings of ductile iron pipes, fittings and accessories used in water mains and distribution system which are specified in ISO 2531, ISO 16631 and can be used to decide the most appropriate protective measures to ensure long term durability of pipeline.
It is not always possible to definitively determine the aggressive parameters of certain water, and fully considered by limited test and evaluation. Therefore, the history information of the evaluated water, experiences of local water works can be taken for reference.
The aggressiveness evaluation of water can be carried out before determining the internal lining materials of certain pipeline, and the evaluation and relevant tests can be done by qualified laboratories and engineers.
Water that leads to high-level scaling in the pipeline is believed aggressive.
Drainage and waste water are not in the scope of this document, the internal protection of drainage and waste water can be recommended by pipe suppliers.
|
Published |
2022-06 |
Edition : 1 |
Number of pages : 19 |
Technical Committee |
23.040.10
Iron and steel pipes
;
91.140.60
Water supply systems
|
| ISO 4422-1:1996 |
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications — Part 1: General |
Specifies the general aspects of pipes, joints, fittings and ancillaries, made of unplasticized poly(vinyl chloride) (PVC-U), for piping systems intended to be used for buried water mains and for water supplies above ground, both inside and outside buildings. Replaces ISO 4422:1990.
|
Withdrawn |
1996-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 4422-2:1996 |
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications — Part 2: Pipes (with or without integral sockets) |
Gives the characteristics and properties of extruded pipes made of unplastized polyvinyl chloride (PVC-U), with or without socket(s) and intended to be used for buried water mains and services and for water supply above ground both inside and outside buildings.
|
Withdrawn |
1996-12 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 4422-3:1996 |
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications — Part 3: Fittings and joints |
Specifies the characteristics and properties of fittings (injection-moulded and postformed) and joints made of unplasticized poly(vinyl chloride) (PVC-U), to be used for buried water mains and for water supplies above ground, both inside and outside buildings.
|
Withdrawn |
1996-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 4422-4:1997 |
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications — Part 4: Valves and ancillary equipment |
|
Withdrawn |
1997-10 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 4422-5:1997 |
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications — Part 5: Fitness for purpose of the system |
|
Withdrawn |
1997-10 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 4422:1990 |
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications |
|
Withdrawn |
1990-08 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
83.140.30
Plastics pipes and fittings for non fluid use
;
91.140.60
Water supply systems
|
| ISO 4422:1990/Amd 1:1992 |
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications — Amendment 1 |
|
Withdrawn |
1992-10 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
83.140.30
Plastics pipes and fittings for non fluid use
;
91.140.60
Water supply systems
|
| ISO 4427-1:2007 |
Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General |
ISO 4427-1:2007 specifies the general aspects of polyethylene (PE) piping systems (mains and service pipes) intended for the conveyance of water for human consumption, including raw water prior to treatment and water for general purposes. It also specifies the test parameters for the test methods to which it refers.
In conjunction with the other parts of ISO 4427, it is applicable to PE pipes, fittings, their joints and to mechanical joints with components of other materials, intended to be used under the following conditions: a maximum operating pressure (MOP) up to and including 25 bar; an operating temperature of 20 °C as the reference temperature.
|
Withdrawn |
2007-08 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 4427-1:2007/Amd 1:2015 |
Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General — Amendment 1: Melt mass-flow rate (MFR) for PE 80 and PE 100 |
|
Withdrawn |
2015-03 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 4427-1:2007/Cor 1:2008 |
Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General — Technical Corrigendum 1 |
|
Withdrawn |
2008-08 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 4427-1:2019 |
Plastics piping systems for water supply and for drainage and sewerage under pressure — Polyethylene (PE) — Part 1: General |
This document specifies the general aspects of polyethylene (PE) compounds for the manufacture of pressure pipes and fittings (mains and service pipes) for buried or above ground applications, intended for the conveyance of:
— water for human consumption;
— raw water prior to treatment;
— drainage and sewerage under pressure;
— vacuum sewer systems;
— water for other purposes.
This document also specifies the test parameters and requirements for the test methods referred to in this document.
In conjunction with other parts of the ISO 4427 series, this document is applicable to PE pipes and fittings, their joints and to joints with components made of PE and other materials, intended to be used under the following conditions:
a) a maximum allowable operating pressure (PFA) up to and including 25 bar[1];
b) an operating temperature of 20 °C as the reference temperature.
NOTE 1 For other operating temperatures, guidance is given in Annex A.
The ISO 4427 series covers a range of maximum allowable operating pressures and gives requirements concerning colours.
NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.
|
Published |
2019-08 |
Edition : 2 |
Number of pages : 17 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 4427-2:2007 |
Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 2: Pipes |
ISO 4427-2:2007 specifies the pipes made from polyethylene (PE) intended for the conveyance of water for human consumption, including raw water prior to treatment and water for general purposes. It also specifies the test parameters for the test methods to which it refers.
In conjunction with the other parts of ISO 4427, it is applicable to PE pipes, their joints, to joints with components of PE and to mechanical joints with components of other materials, intended to be used under the following conditions: a maximum operating pressure (MOP) up to and including 25 bar; an operating temperature of 20 °C as the reference temperature.
|
Withdrawn |
2007-08 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 4427-2:2007/Amd 1:2014 |
Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 2: Pipes — Amendment 1 |
|
Withdrawn |
2014-04 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 7259:1988 |
Predominantly key-operated cast iron gate valves for underground use |
Specifies requirements for two types of predominantly key-operated valves for underground use with flanges or spigot ends or socket ends. The two types shall be specified as type A or type B and shall include the following features: inside screw stem; wedge or parallel obturator; metallic or elastomeric obturator seatings; metallic or elastomeric body seatings; ferrous metal and/or copper alloy trims; T-key operation; ring key and bar operation. Type A valves are for T-key operation; type B valves are for ring key and bar operation.
|
Withdrawn |
1988-12 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
23.060.30
Gate valves
;
91.140.60
Water supply systems
|
| ISO 4427-2:2019 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure — Polyethylene (PE) — Part 2: Pipes |
This document specifies the pipes made from polyethylene (PE) for buried or above ground applications, intended for the conveyance of:
— water for human consumption;
— raw water prior to treatment;
— drainage and sewerage under pressure;
— vacuum sewer systems;
— water for other purposes.
NOTE 1 The intended uses include sea outfalls, laid in water and pipes suspended below bridges.
Pipes complying with this document are not intended for the transport of water intended for human consumption in contaminated soils unless special consideration has been taken.
NOTE 2 For example, ISO 21004 provides an alternative solution for use in contaminated soils. See Reference [3] in the Bibliography.
This document specifies three types of pipe:
— PE pipes (outside diameter dn), including any identification stripes;
— PE pipes with co-extruded layers on either or both the outside and/or inside of the pipe (total outside diameter dn) where all layers have the same MRS rating;
— PE pipes (outside diameter dn) having a peelable and contiguous thermoplastics additional layer on the outside of the pipe ("coated pipe").
This document also specifies the test parameters for the test methods referred to in this document.
In conjunction with the other parts of the ISO 4427 series, this document is applicable to PE pipes, their joints and to joints with components made of PE and other materials, intended to be used under the following conditions:
a) a maximum allowable operating pressure (PFA) up to and including 25 bar[1];
b) an operating temperature of 20 °C as the reference temperature.
NOTE 3 For other operating temperatures, guidance is given in ISO 4427‑1:2019, Annex A.
This document covers a range of maximum allowable operating pressures and gives requirements concerning colours.
NOTE 4 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.
|
Published |
2019-08 |
Edition : 2 |
Number of pages : 20 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 4427-2:2019/Amd 1:2023 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure — Polyethylene (PE) — Part 2: Pipes — Amendment 1 |
|
Published |
2023-02 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 4427-3:2007 |
Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 3: Fittings |
ISO 4427-3:2007 specifies the general aspects of fittings made from polyethylene (PE) for piping systems intended for the conveyance of water for human consumption, including raw water prior to treatment and water for general purposes. It also specifies the test parameters for the test methods to which it refers.
In conjunction with the other parts of ISO 4427, it is applicable to PE fittings, their joints, to joints with components of PE and to joints with mechanical fittings of other materials, intended to be used under the following conditions: a maximum operating pressure (MOP) up to and including 25 bar; an operating temperature of 20 °C as the reference temperature.
|
Withdrawn |
2007-08 |
Edition : 1 |
Number of pages : 31 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 4427-3:2019 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure — Polyethylene (PE) — Part 3: Fittings |
This document specifies the fittings made from polyethylene (PE) for buried or above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.
NOTE 1 The intended uses include sea outfalls, laid in water and connection between pipes suspended below bridges.
This document also specifies the test parameters for the test methods referred to in this document.
In conjunction with the other parts of the ISO 4427 series, this document is applicable to PE fittings, to joints with components of PE or other materials, intended to be used under the following conditions:
a) a maximum allowable operating pressure (PFA) up to and including 25 bar[1];
b) an operating temperature of 20 °C as the reference temperature.
NOTE 2 For other operating temperatures, guidance is given in ISO 4427‑1:2019, Annex A.
This document covers a range of maximum allowable operating pressures and gives requirements concerning colours.
NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes.
This document is applicable to fittings of the following types:
1. fusion fittings;
a. electrofusion fittings;
b. spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion);
c. socket fusion fittings (see Annex A);
2. mechanical fittings;
a. compression fittings;
b. flanged fittings;
3. fabricated fittings (see Annex B).
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.
|
Published |
2019-07 |
Edition : 2 |
Number of pages : 35 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 4427-5:2007 |
Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 5: Fitness for purpose of the system |
ISO 4427-5:2007 specifies the characteristics of the fitness for purpose of assembled piping systems made from polyethylene (PE) intended for the conveyance of water for human consumption, including raw water prior to treatment and water for general purposes. It also specifies the test parameters for the test methods to which it refers.
In conjunction with the other parts of ISO 4427, it is applicable to PE pipes, fittings, valves, their joints and to joints with components of other materials, intended to be used under the following conditions: a maximum operating pressure (MOP) up to and including 25 bar; an operating temperature of 20 °C as the reference temperature.
|
Withdrawn |
2007-08 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 7858-1:1985 |
Measurement of water flow in closed conduits — Meters for cold potable water — Combination meters — Part 1: Specifications |
|
Withdrawn |
1985-07 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 7858-1:1998 |
Measurement of water flow in closed conduits — Combination meters for cold potable water — Part 1: Specifications |
|
Withdrawn |
1998-07 |
Edition : 2 |
Number of pages : 5 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 4427-5:2019 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure — Polyethylene (PE) — Part 5: Fitness for purpose of the system |
This document specifies the characteristics of the fitness for purpose of pipes and/or fittings assemblies made from polyethylene (PE) for buried or above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.
NOTE 1 The intended uses include sea outfalls, laid in water and pipes suspended below bridges.
NOTE 2 This document is intended to be only used by the product manufacturer to assess the performance of components according to ISO 4427‑2 and/or ISO 4427‑3 when joined together under normal and extreme conditions. It is not intended for on-site testing of pipe systems.
This document also specifies the test parameters for the test methods referred to in this document.
In conjunction with the other parts of the ISO 4427 series, this document is applicable to PE pipes, fittings, their joints and to joints with components of PE and other materials, intended to be used under the following conditions:
a) a maximum allowable operating pressure (PFA) up to and including 25 bar[1];
b) an operating temperature of 20 °C as the reference temperature.
NOTE 3 For other operating temperatures, guidance is given in ISO 4427‑1: 2019, Annex A.
The ISO 4427 series covers a range of maximum allowable operating pressures and gives requirements concerning colours.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.
|
Published |
2019-08 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 4427:1996 |
Polyethylene (PE) pipes for water supply — Specifications |
Specifies the required properties of pipes made from polyethylene (PE) to be used for buried water mains and services and for water supply above ground both inside and outside buildings. In addition, it contains specifications for some general properties of the material from which these pipes are made, including a classification scheme.
|
Withdrawn |
1996-12 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|