| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO 6804:1982 |
Rubber hose and hose assemblies — Washing-machines and dishwashers — Specification |
|
Withdrawn |
1982-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
97.060
Laundry appliances
;
83.140.40
Hoses
;
97.040.40
Dishwashers
|
| ISO 16422:2006 |
Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Specifications |
ISO 16422:2006 specifies the general aspects of pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O), for piping systems intended to be used underground or above-ground where not exposed to direct sunlight, for water mains and services, pressurized sewer systems and irrigation systems.
The piping system according to ISO 16422:2006 is intended for the conveyance of cold water under pressure, for drinking water and for general purposes up to and including 45 degrees Celsius, and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations, up to pressure ratings of 25 bar.
|
Withdrawn |
2006-05 |
Edition : 1 |
Number of pages : 24 |
Technical Committee |
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 16422:2014 |
Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure — Specifications |
ISO 16422:2014 specifies the requirements of pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O), for piping systems intended to be used underground or above-ground where not exposed to direct sunlight, for water mains and services, pressurized sewer systems and irrigation systems.
The piping system according to ISO 16422:2014 is intended for the conveyance of cold water under pressure, for drinking water and for general purposes up to and including 45 °C, and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations, up to pressure of 25 bars[1].
Joints constructed of other materials should meet their own relevant standards in addition to the fitness-for-purpose requirements of ISO 16422:2014.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2
|
Published |
2014-02 |
Edition : 2 |
Number of pages : 26 |
Technical Committee |
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 16631:2016 |
Ductile iron pipes, fittings, accessories and their joints compatible with plastic (PVC or PE) piping systems, for water applications and for plastic pipeline connections, repair and replacement |
ISO 16631:2016 specifies the requirements and test methods applicable to ductile iron pipes, fittings, accessories and their joints with dimensions compatible with plastic (PVC or PE) piping systems:
- to replace or repair existing plastic pipelines;
- to convey water (e.g. for human consumption, raw water, etc.);
- operated with or without pressure;
- installed below or above ground;
- defined according to their external diameter (DN/OD series);
- classified according to pressure (C class).
The pressure class specified in this International Standard is C25. This pressure resistance level will meet or exceed those of plastic pipes. These ductile iron pipes, fittings, accessories and joints can be used along with plastic pipelines, where they are needed (for example, with higher pressure rating sections, higher traffic load, etc.), for the construction of water pipelines.
The dimensions of the products according to this International Standard, in the size range DN/OD 50 to DN/OD 225, are compatible with those of plastic pipes (ISO 1452‑2 for PVC and ISO 4427‑2 for PE). The spigots of plastic pipes used for water applications can be inserted into sockets of pipes manufactured according to this International Standard. The spigots and sockets of products defined in this International Standard are not dimensionally compatible with the products defined in ISO 2531.
ISO 16631:2016 gives specifications for materials, dimensions and tolerances, mechanical properties and standard coatings and linings of pipes, fittings and accessories. It also gives performance requirements for all components including joints.
ISO 16631:2016 covers pipes, fittings and accessories cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints in the size range DN/OD 50 to DN/OD 225 inclusive.
ISO 16631:2016 is applicable to pipes, fittings and accessories which are
- manufactured with socketed or spigot ends for jointing by means of various types of gaskets (which are not within the scope of this International Standard), and
- compulsory delivered internally and externally coated.
ISO 16631:2016 is also applicable to socketed fittings which include flanged connections.
NOTE In this International Standard, all pressures are relative pressures expressed in bar[1].
[1] 100 kPa = 1 bar.
|
Published |
2016-03 |
Edition : 1 |
Number of pages : 49 |
Technical Committee |
77.140.75
Steel pipes and tubes for specific use
;
91.140.60
Water supply systems
|
| ISO 21003-1:2008 |
Multilayer piping systems for hot and cold water installations inside buildings — Part 1: General |
ISO 21003-1:2008 specifies the general aspects of multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or heating systems — under specified design pressures and temperatures appropriate to the class of application.
ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. ISO 23001-1 is intended for use only in conjunction with all the other parts of ISO 21003.
|
Published |
2008-07 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO 21003-2:2008 |
Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes |
ISO 21003-2:2008 specifies the characteristics of pipes for multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or heating systems — under specified design pressures and temperatures appropriate to the class of application.
It also specifies the test parameters for the test methods referred to in this part of ISO 21003.
ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. ISO 21003-2 is intended for use only in conjunction with all the other parts of ISO 21003.
|
Published |
2008-07 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 21003-2:2008/Amd 1:2011 |
Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes — Amendment 1 |
|
Published |
2011-04 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 21003-3:2008 |
Multilayer piping systems for hot and cold water installations inside buildings — Part 3: Fittings |
ISO 21003-3:2008 specifies the characteristics of fittings for multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or for heating systems — under specified design pressures and temperatures appropriate to the class of application
It also specifies the test parameters for the test methods referred to in this part of ISO 21003.
ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. ISO 21003-3 is intended for use only in conjunction with all the other parts of ISO 21003.
|
Published |
2008-07 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 21003-3:2008/Amd 1:2021 |
Multilayer piping systems for hot and cold water installations inside buildings — Part 3: Fittings — Amendment 1 |
|
Published |
2021-10 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 21003-5:2008 |
Multilayer piping systems for hot and cold water installations inside buildings — Part 5: Fitness for purpose of the system |
ISO 21003-5:2008 specifies the characteristics for the fitness for purpose of multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or for heating systems — under specified design pressures and temperatures appropriate to the class of application.
It also specifies the test parameters for the test methods referred to in this part of ISO 21003.
ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. ISO 21003-5 is intended for use only in conjunction with all the other parts of ISO 21003.
|
Published |
2008-07 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO/TS 21003-7:2008 |
Multilayer piping systems for hot and cold water installations inside buildings — Part 7: Guidance for the assessment of conformity |
ISO/TS 21003-7:2008 is applicable, in conjunction with the other parts of ISO 21007, to multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or for heating systems — under specified design pressures and temperatures appropriate to the class of application. It gives guidance for the assessment of conformity, to be included in the manufacturer's quality plan as part of the quality system.
It includes:
requirements for materials, components, joints and assemblies given in the applicable part(s) of ISO 21003;
requirements for the manufacturer's quality system (e.g. ISO 9001);
definitions and procedures to be used if third-party certification is involved.
|
Withdrawn |
2008-07 |
Edition : 1 |
Number of pages : 15 |
Technical Committee |
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO/TS 21003-7:2008/Amd 1:2010 |
Multilayer piping systems for hot and cold water installations inside buildings — Part 7: Guidance for the assessment of conformity — Amendment 1 |
|
Withdrawn |
2010-09 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO/TS 21003-7:2019 |
Multilayer piping systems for hot and cold water installations inside buildings — Part 7: Guidance for the assessment of conformity |
This document gives requirements and guidance for the assessment of conformity of compounds, products, and assemblies in accordance with the applicable part(s) of ISO 21003 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.
In conjunction with the other parts of ISO 21003 (see Foreword), this document is applicable to multilayer piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see ISO 21003-1:2008, Table 1).
|
Published |
2019-04 |
Edition : 2 |
Number of pages : 31 |
Technical Committee |
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 21053:2019 |
Life cycle analysis and recycling of ductile iron pipes for water applications |
This document specifies the evaluation method of life cycle analysis of ductile iron pipes used for water applications as specified in ISO 2531 and ISO 16631.
Studies on economic and environmental impacts are important for utility decision-makers as they seek to balance budget concerns over immediate and long-term needs across acquisition, operations and maintenance, and planned end of life. For authorities and engineers designing pipeline systems, the life cycle cost analysis serves as a tool to study various scenarios to determine the right solution for site-specific conditions and community values, as well as to provide the necessary data to support those decisions.
Informative annexes are included in this document as a compilation of reference and consensual factors (pumping cost, leakage incident rate, etc.).
|
Published |
2019-07 |
Edition : 1 |
Number of pages : 15 |
Technical Committee |
77.140.75
Steel pipes and tubes for specific use
;
91.140.60
Water supply systems
|
| ISO 22391-1:2007 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 1: General |
ISO 22391-1:2007 specifies the general aspects of piping systems made of polyethylene of raised temperature resistance (PE-RT), intended to be used for hot and cold water installations within buildings for the conveyance of water -- whether or not the water is intended for human consumption (domestic systems) or heating systems -- under specified design pressures and temperatures according to the class of application.
It covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and defines terms, symbols and abbreviated terms for the whole of ISO 22391. When used in conjunction with the other parts of ISO 22391, it is respectively applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT as well as of other plastics and non-plastics materials, used for hot and cold water installations.
It is not applicable for values of design temperature, maximum design temperature or malfunction temperature in excess of those it specifies.
|
Withdrawn |
2007-01 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO 22391-1:2009 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 1: General |
ISO 22391-1:2009 specifies the general characteristics of piping systems made of polyethylene of raised temperature resistance (PE‑RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under specified design pressures and temperatures appropriate to the class of application.
ISO 22391-1:2009 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and defines terms. In conjunction with the other parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints and to joints having components of PE-RT, as well as of other plastics and non-plastics materials, respectively, used for hot and cold water installations.
|
Published |
2009-12 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO 22391-2:2007 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 2: Pipes |
This part of ISO 22391 specifies the characteristics of pipe made from polyethylene of raised temperature resistance (PE-RT), intended to be used for hot and cold water installations within buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or heating systems — under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
It covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. When used in conjunction with the other parts of ISO 22391, it is respectively applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT as well as of other plastics and non-plastics materials, used for hot and cold water installations.
It is applicable to pipes with or without a barrier layer or layers.
It is not applicable for values of design temperature, maximum design temperature or malfunction temperature in excess of those specified in ISO 22391-1.
NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
|
Withdrawn |
2007-01 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 22391-2:2009 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 2: Pipes |
ISO 22391-2:2009 specifies the characteristics of pipe made of polyethylene of raised temperature resistance (PE-RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
ISO 22391-2:2009 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. When used in conjunction with the other parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT, as well as of other plastics and non-plastics materials, respectively, used for hot and cold water installations.
It is applicable to pipes with or without a barrier layer or layers.
|
Published |
2009-12 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 22391-2:2009/Amd 1:2020 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 2: Pipes — Amendment 1 |
|
Published |
2020-11 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 7172:1988 |
Furniture — Tables — Determination of stability |
|
Published |
1988-05 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
97.140
Furniture
|
| ISO 22391-3:2007 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 3: Fittings |
ISO 22391-3:2007 specifies the characteristics of fittings for piping systems made from polyethylene of raised temperature resistance (PE-RT), intended to be used for hot and cold water installations within buildings for the conveyance of water -- whether or not the water is intended for human consumption (domestic systems) or heating systems -- under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
It covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. When used in conjunction with the other parts of ISO 22391, it is applicable to fittings made from PE-RT, as well as to those made from other materials, intended to be fitted to pipes conforming to ISO 22391-2 for hot and cold water installations, the joints of which are in accordance with ISO 22391-5.
ISO 22391-3:2006 is applicable to the following types of fitting: mechanical fittings; socket fusion fitting; electrofusion fittings; fittings with incorporated inserts.
It is not applicable for values of design temperature, maximum design temperature or malfunction temperature in excess of those specified in ISO 22391-1.
|
Withdrawn |
2007-01 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 22391-3:2009 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 3: Fittings |
ISO 22391-3:2009 specifies the characteristics of fittings for piping systems made of polyethylene of raised temperature resistance (PE-RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
ISO 22391-3:2009 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. In conjunction with the other parts of ISO 22391, it is applicable to fittings made of PE-RT, as well as to those made of other materials, intended to be fitted to pipes conforming to ISO 22391-2 for hot and cold water installations, the joints of which are in accordance with ISO 22391-5.
It is applicable to the following types of fitting:
- mechanical fittings;
- socket fusion fitting;
- electrofusion fittings;
- fittings with incorporated inserts.
|
Published |
2009-12 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 22391-3:2009/Amd 1:2020 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 3: Fittings — Amendment 1 |
|
Published |
2020-12 |
Edition : 2 |
Number of pages : 1 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 22391-3:2009/Amd 2:2021 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 3: Fittings — Amendment 2 |
|
Published |
2021-10 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.45
Plastics fittings
;
91.140.60
Water supply systems
|
| ISO 22391-5:2007 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 5: Fitness for purpose of the system |
ISO 22391-5:2007 specifies the characteristics of the fitness for purpose of piping systems made from polyethylene of raised temperature resistance (PE-RT), intended to be used for hot and cold water installations within buildings for the conveyance of water -- whether or not the water is intended for human consumption (domestic systems) or heating systems -- under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
It covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. When used in conjunction with the other parts of ISO 22391, it is respectively applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT as well as of other plastics and non-plastics materials, used for hot and cold water installations.
It is not applicable for values of design temperature, maximum design temperature or malfunction temperature in excess of those specified in ISO 22391-1.
|
Withdrawn |
2007-01 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO/TR 7074:1986 |
Performance requirements for plastics pipes and fittings for use in underground drainage and sewage |
Specification of four prepared test methods for performance and long-time tests and discussion of the available results and their significance and comparability: box loading test (BLT), water cycling test (WCT), impact resistance test (IRT), and fatigue bending test (FBT).
|
Withdrawn |
1986-02 |
Edition : 1 |
Number of pages : 22 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
91.140.80
Drainage systems
|
| ISO 22391-5:2009 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 5: Fitness for purpose of the system |
ISO 22391-5:2009 specifies the characteristics of the fitness for purpose of piping systems made of polyethylene of raised temperature resistance (PE-RT), Type I and polyethylene of raised temperature resistance (PE-RT), Type II, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under the design pressures and temperatures appropriate to the class of application according to ISO 22391-1.
ISO 22391-5:2009 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. In conjunction with the other parts of ISO 22391, it is applicable to PE-RT pipes, fittings, their joints, and to joints having components of PE-RT as well as of other plastics and non-plastics materials, respectively, used for hot and cold water installations.
|
Published |
2009-12 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO 22391-5:2009/Amd 1:2020 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 5: Fitness for purpose of the system — Amendment 1 |
|
Published |
2020-12 |
Edition : 2 |
Number of pages : 3 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO/TS 22391-7:2011 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 7: Guidance for the assessment of conformity |
ISO/TS 22391-7:2011 gives guidance on the assessment of conformity of products and assemblies in accordance with other applicable part(s) of ISO 22391 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of third-party certification procedures.
In conjunction with the other parts, ISO/TS 22391-7:2011 is applicable to hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems), under design pressures and temperatures appropriate to the class of application.
|
Withdrawn |
2011-11 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO/TS 22391-7:2018 |
Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 7: Guidance for the assessment of conformity |
This document gives requirements and guidance for the assessment of conformity of materials, products, and assemblies in accordance with the applicable part(s) of ISO 22391 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with the other parts of ISO 22391 (see Foreword), this document is applicable to polyethylene of raised temperature resistance (PE-RT) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see ISO 22391-1:2009, Table 1).
|
Published |
2018-11 |
Edition : 2 |
Number of pages : 16 |
Technical Committee |
93.025
External water conveyance systems
;
23.040.01
Pipeline components and pipelines in general
;
91.140.60
Water supply systems
|
| ISO 23711:2003 |
Elastomeric seals — Requirements for materials for pipe joint seals used in water and drainage applications — Thermoplastic elastomers |
ISO 23711:2003 specifies requirements for materials used for moulded seals made of thermoplastic elastomers (TPEs) for joints in:
thermoplastic piping systems for non-pressure waste water discharge (intermittent flow at up to 95 °C) inside buildings;thermoplastic piping systems for non-pressure underground drainage and sewerage (continuous flow at up to 45 °C and intermittent flow at up to 95 °C);thermoplastic rainwater piping systems.
General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design.
|
Withdrawn |
2003-12 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
83.140.50
Seals
;
91.140.60
Water supply systems
;
91.140.80
Drainage systems
|
| ISO 7186:1996 |
Ductile iron products for sewage applications |
Requirements and test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of drains and sewers outside buildings.
|
Withdrawn |
1996-12 |
Edition : 2 |
Number of pages : 22 |
Technical Committee |
93.030
External sewage systems
;
77.140.80
Iron and steel castings
|
| ISO 23711:2022 |
Elastomeric seals — Requirements for materials for pipe joint seals used in water and drainage applications — Thermoplastic elastomers |
This document specifies requirements for materials used for moulded seals made of thermoplastic elastomers (TPEs) for joints in:
a) thermoplastic piping systems for non-pressure wastewater discharge (intermittent flow at up to 95 °C) inside buildings;
b) thermoplastic piping systems for non-pressure underground drainage and sewerage (continuous flow at up to 45 °C and intermittent flow at up to 95 °C);
c) thermoplastic rainwater piping systems.
General requirements for finished joint seals are also given; any additional requirements for a particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design.
|
Published |
2022-10 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
83.140.50
Seals
;
91.140.60
Water supply systems
;
91.140.80
Drainage systems
|
| ISO/TS 24520:2017 |
Service activities relating to drinking water supply systems and wastewater systems — Crisis management — Good practice for technical aspects |
ISO/TS 24520:2017 provides guidance to water utilities on good practice in technical aspects of crisis management.
ISO/TS 24520:2017 is applicable to all water utilities, of whatever size, whether public or private, that wish to review the effectiveness and efficiency of their service activities relating to preparation for, response to and recovery from a crisis.
|
Published |
2017-09 |
Edition : 1 |
Number of pages : 43 |
Technical Committee |
03.080.30
Services for consumers
;
13.060.20
Drinking water
;
13.060.30
Sewage water
;
91.140.60
Water supply systems
|
| ISO 25780:2011 |
Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Pipes with flexible joints intended to be installed using jacking techniques |
ISO 25780:2011 specifies the properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) for water supply, irrigation, drainage or sewerage systems with or without pressure.
ISO 25780:2011 is applicable to GRP-UP piping systems, with flexible joints, intended to be installed using jacking techniques. It specifies the characteristics of pipes made from GRP-UP, with or without aggregates or fillers and also specifies the test parameters for the test methods referred to in ISO 25780:2011.
ISO 25780:2011 is applicable to pipes and joints with a size range from DN100 to DN4000 which are intended to be used for the conveyance of water or sewage at temperatures up to 50ºC, with or without pressure.
ISO 25780:2011 covers requirements to improve the design of the joint and specifies type test performance requirements for the joints as a function of the declared nominal pressure rating of the pipeline system and the required joint deflection capability of the system.
|
Published |
2011-05 |
Edition : 1 |
Number of pages : 51 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
;
91.140.80
Drainage systems
|
| ISO/TR 27165:2012 |
Thermoplastics piping systems - Guidance for definitions of wall constructions for pipes |
ISO/TR 27165:2012 provides definitions for wall constructions of thermoplastics pipes intended to be used in pressure and non-pressure pipe applications. It takes into account as far as possible already existing definitions in published product standards and gives guidance for a common text when drafting new deliverables or revising existing ones.
|
Published |
2012-10 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
|
| ISO 4435:1991 |
Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings for buried drainage and sewerage systems — Specifications |
|
Withdrawn |
1991-05 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
93.030
External sewage systems
;
83.140.30
Plastics pipes and fittings for non fluid use
|
| ISO 4435:2003 |
Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U) |
ISO 4435:2003 specifies the requirements for unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and piping systems intended for use for non-pressure underground drainage and sewerage for the conveyance of soil and waste discharge of domestic and industrial origin, as well as surface water.
It covers buried pipework but does not apply to piping systems buried within the building structure.
It is applicable to PVC-U pipes with or without an integral socket.
|
Published |
2003-02 |
Edition : 2 |
Number of pages : 22 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
|
| ISO/FDIS 4982 |
Plastics piping systems for non-pressure underground conveyance and storage of non-potable water — Arch-shaped, corrugated wall chambers made of PE or PP used for retention, detention, storage and transportation of storm water systems — Product specifications and performance criteria |
|
Under development |
|
Edition : 1 |
Number of pages : 36 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 7186:2011 |
Ductile iron products for sewerage applications |
ISO 7186:2011 specifies the requirements and test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of drains and sewers outside buildings:
- to convey surface water (e.g. rainwater), domestic waste water and/or certain types of industrial effluents, either in separate systems or in combined systems;
- operating without pressure (gravity sewers) or with positive or negative pressure;
- for installation below or above ground.
ISO 7186:2011 contains specifications for materials, dimensions and tolerances, mechanical properties and standard coatings of pipes, fittings and accessories. It also gives performance requirements for all components including joints.
ISO 7186:2011 is applicable to pipes, fittings and accessories cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints, in the size range DN 80 to DN 2600 inclusive.
It is applicable to pipes, fittings and accessories which are manufactured with socketed, flanged or spigot ends (joint design and gasket shape are outside the scope of ISO 7186:2011) and normally delivered internally and externally coated.
|
Published |
2011-07 |
Edition : 3 |
Number of pages : 36 |
Technical Committee |
93.030
External sewage systems
;
77.140.80
Iron and steel castings
|
| ISO 8772:1991 |
High-density polyethylene (PE-HD) pipes and fittings for buried drainage and sewerage systems — Specifications |
|
Withdrawn |
1991-05 |
Edition : 1 |
Number of pages : 15 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 8772:2006 |
Plastics piping systems for non-pressure underground drainage and sewerage — Polyethylene (PE) |
ISO 8772:2006 specifies the requirements for polyethylene (PE) pipes, fittings and piping systems intended for use for non-pressure underground drainage and sewerage for the conveyance of soil and waste discharge of domestic and industrial origin, as well as surface water.
It covers buried pipework, as well as piping systems buried within the building structure.
In the case of industrial discharge, it is necessary that the chemical and temperature resistance be taken into account, but this will need to be done separately.
ISO 8772:2006 is applicable to PE pipes with or without an integral socket.
This International Standard is applicable to PE pipes and fittings for the following types of joints: elastomeric ring seal joints; butt fused joints; electrofusion joints; mechanical joints.
ISO 8772:2006 also specifies the test parameters for the test methods referred to therein.
|
Published |
2006-09 |
Edition : 2 |
Number of pages : 22 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 8773:1991 |
Polypropylene (PP) pipes and fittings for buried drainage and sewerage systems — Specifications |
|
Withdrawn |
1991-05 |
Edition : 1 |
Number of pages : 15 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 8773:2006 |
Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene (PP) |
ISO 8773:2006 specifies the requirements for polypropylene (PP) pipes, fittings and piping systems intended for use for non-pressure underground drainage and sewerage for the conveyance of soil and waste discharge of domestic and industrial origin, as well as surface water.
It covers buried pipework, as well as piping systems buried within the building structure.
In the case of industrial discharge, it is necessary that the chemical and temperature resistance be taken into account, but this will need to be done separately.
ISO 8773:2006 is applicable to PP pipes with or without an integral socket and to jointing by means of push fit joints with sealing rings or butt-fused joints.
It covers PP materials with normal E moduli and with higher E moduli, designated as HM (higher modulus), and gives a range of nominal sizes and pipe series, as well as recommendations concerning colours.
ISO 8773:2006 also specifies the test parameters for the test methods referred to therein.
|
Published |
2006-09 |
Edition : 2 |
Number of pages : 22 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 10467:2004 |
Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
ISO 10467:2004 specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) for drainage or sewerage with or without pressure, as well as the properties of the system itself.
It is applicable to GRP-UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in buried installations.
It is applicable to pipes, fittings and their joints of nominal sizes from DN 50 to DN 4000 which are intended to be used for the conveyance of surface water or sewage at temperatures up to 50 °C, with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together.
|
Withdrawn |
2004-02 |
Edition : 1 |
Number of pages : 75 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
91.140.80
Drainage systems
|
| ISO 10467:2004/Amd 1:2012 |
Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Amendment 1 |
|
Withdrawn |
2012-03 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
91.140.80
Drainage systems
|
| ISO 10467:2018 |
Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
This document specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of drainage and sewerage with or without pressure. This document is applicable to GRP UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in direct buried installations.
NOTE 1 For the purpose of this document, the term polyester resin (UP) also includes vinyl-ester resins (VE).
NOTE 2 Piping systems conforming to this document can also be used for non-buried applications, provided the influence of the environment and the supports are considered in the design of the pipes, fittings and joints.
NOTE 3 This document can also apply for other installations, such as slip-lining rehabilitation of existing pipes.
NOTE 4 This document is also referenced in ISO 25780, which specifies requirements for GRP-pipes used for jacking installation.
The requirements for the hydrostatic pressure design of pipes referring to this document meet the requirements of ISO/TS 20656‑1 and the general principle for the reliability of structures detailed in ISO 2394 and in EN 1990. These International Standards provide procedures for the harmonization of design practices and address the probability of failure, as well as possible consequences of failures. The design practices are based on a partial safety factor concept, as well as on risk management engineering.
This document is applicable to pipes, fittings and their joints of nominal sizes from DN 50 to DN 4000 which are intended to be used for the conveyance of water at temperatures up to 50 °C, with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together. Clause 4 specifies the general aspects of GRP UP piping systems intended to be used in the field of drainage or sewerage with or without pressure.
Clause 5 specifies the characteristics of pipes made from GRP UP with or without aggregates and/or fillers. The pipes may have a thermoplastics or thermosetting resin liner. Clause 5 also specifies the test parameters for the test methods referred to in this document.
Clause 6 specifies the characteristics of fittings made from GRP UP, with or without a thermoplastics or thermosetting resin liner, intended to be used in the field of drainage and sewerage. Clause 6 specifies the dimensional and performance requirements for bends, branches, reducers, saddles and flanged adaptors. Clause 6 covers requirements to prove the structural design of fittings. It is applicable to fittings made using any of the following techniques:
— fabrication from straight pipes;
— moulding by
filament winding,
tape winding,
contact moulding, and
hot or cold compression moulding.
Clause 7 is applicable to the joints to be used in GRP UP piping systems to be used for the conveyance of surface water and sewerage, both buried and non-buried. It covers requirements to prove the design of the joint. Clause 7 specifies type test performance requirements for the following joints as a function of the declared nominal pressure rating of the pipeline or system:
a) socket-and-spigot (including double-socket) joints or mechanical joints;
b) locked socket-and-spigot joints;
c) cemented or wrapped joints;
d) bolted flange joints.
|
Withdrawn |
2018-06 |
Edition : 2 |
Number of pages : 59 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
91.140.80
Drainage systems
|
| ISO 11296-1:2009 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 1: General |
ISO 11296-1:2009 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground non‑pressure drainage and sewerage networks, which are operated as gravity systems and subjected to a maximum surcharge pressure of 0,5 bar. It is applicable to pipes and fittings as manufactured, as well as to the installed plastics lining system; it is not applicable to the existing pipeline or any annular filler.
|
Withdrawn |
2009-11 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11296-1:2018 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 1: General |
ISO 11296-1:2018 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground non-pressure drainage and sewerage networks, which are operated as gravity systems and subjected to a maximum surcharge pressure of 0,5 bar[1]. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is not applicable to the existing pipeline or any non-structural sprayed coatings or annular filler.
ISO 11296-1:2018 gives the general requirements common to all relevant renovation techniques.
[1] 1 bar = 0,1 MPa = 0,1 N/mm2 = 105 N/m2.
|
Published |
2018-02 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11296-2:2018 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 2: Lining with continuous pipes |
ISO 11296-2:2018, in conjunction with ISO 11296-1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground non-pressure drainage and sewerage networks. It is applicable to polyethylene (PE) pipes of three different types:
- PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes;
- PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating;
- PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe ("coated pipe"), see Annex A.
In addition, ISO 11296-2:2018 covers:
- jointing of pipe lengths by means of butt fusion;
- fabricated and injection-moulded fittings made of PE.
|
Published |
2018-02 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11296-3:2009 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 3: Lining with close-fit pipes |
ISO 11296-3:2009, in conjunction with ISO 11296-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of non-pressure drainage and sewerage networks.
It applies to pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC‑U). It is applicable to the plastic lining system only.
|
Withdrawn |
2009-11 |
Edition : 1 |
Number of pages : 19 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11296-3:2009/Cor 1:2011 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 3: Lining with close-fit pipes — Technical Corrigendum 1 |
|
Withdrawn |
2011-05 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 4210-6:2023 |
Cycles — Safety requirements for bicycles — Part 6: Frame and fork test methods |
This document specifies the frame and fork test methods for ISO 4210‑2.
|
Published |
2023-01 |
Edition : 3 |
Number of pages : 29 |
Technical Committee |
43.150
Cycles
|
| ISO 11296-3:2018 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 3: Lining with close-fit pipes |
This document, in conjunction with ISO 11296‑1, specifies requirements and test methods for close-fit lining systems used for the renovation of underground non-pressure drainage and sewerage networks.
It applies to pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC‑U) as manufactured, as well to the installed lining system with its associated joints.
|
Published |
2018-08 |
Edition : 2 |
Number of pages : 15 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11296-4:2009 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 4: Lining with cured-in-place pipes |
ISO 11296-4:2009, in conjunction with ISO 11296-1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of underground non-pressure drainage and sewerage networks.
It applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials and other process-related plastics components.
|
Withdrawn |
2009-11 |
Edition : 1 |
Number of pages : 32 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11296-4:2018 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 4: Lining with cured-in-place pipes |
ISO 11296-4:2018, in conjunction with ISO 11296‑1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of underground non-pressure drainage and sewerage networks with service temperatures up to 50 °C.
ISO 11296-4:2018 applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials, reinforcement, and other process-related plastics components (see 5.3).
|
Published |
2018-02 |
Edition : 2 |
Number of pages : 39 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11296-4:2018/Amd 1:2021 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 4: Lining with cured-in-place pipes — Amendment 1: Updated definitions, marking requirements and procedure for alternative expression of flexural test results |
|
Published |
2021-02 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11296-7:2011 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 7: Lining with spirally-wound pipes |
|
Withdrawn |
2011-11 |
Edition : 1 |
Number of pages : 16 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11296-7:2019 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 7: Lining with spirally-wound pipes |
This document, in conjunction with ISO 11296-1, specifies requirements and test methods for pipes which are formed on site by spirally winding and jointing a pre-manufactured profiled plastics strip, or a profiled plastics strip and integral locking joiner strip, and used for the renovation of underground non-pressure drainage and sewerage networks.
It applies to spirally-wound pipes of fixed or variable diameter made of profiled plastics strips, with or without steel stiffening elements, and installed by one of two methods.
The first method employs a dedicated winding machine in front of the open end of an existing pipeline, e.g. in a manhole. The pipes thus formed are simultaneously inserted into the existing pipeline by the winding forces, and by certain techniques can also be expanded in diameter after or during insertion.
The second method employs a dedicated winding machine which forms the pipe as it traverses the existing pipeline from one manhole to the next.
It applies to profiled plastics strips of unplasticized poly(vinyl chloride) (PVC U) with integral locking mechanism, or of high density polyethylene (HDPE) with integrally welded joints.
|
Published |
2019-01 |
Edition : 2 |
Number of pages : 16 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 22074-6:2021 |
Railway infrastructure — Rail fastening systems — Part 6: Test method for resistance to severe environmental conditions |
This document specifies a laboratory test procedure for finding the effect of exposure to severe environmental conditions on the fastening system.
This test procedure applies to a complete fastening assembly including embedded rail with mechanical fastenings. It is not applicable to embedded rail systems relying on adhesive components to secure the rail.
|
Published |
2021-03 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
45.080
Rails and railway components
|
| ISO 11296-9:2022 |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 9: Lining with a rigidly anchored plastics inner layer |
This document, in conjunction with ISO 11296‑1, specifies the requirements and test methods for pipes and fittings for the renovation of underground non-pressure drainage and sewerage networks by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer. This plastics layer serves as permanent formwork anchored to the grout.
This document is applicable to plastics inner layers and grout systems with or without steel reinforcement. It does not apply to the structural design of the lining system.
NOTE Systems with multiple annuli are available, but these are controlled by patent rights and not covered by this document.
|
Published |
2022-09 |
Edition : 1 |
Number of pages : 29 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11297-1:2013 |
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 1: General |
ISO 11297-1:2013 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground drainage and sewerage networks under pressure. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is not applicable to cover sprayed coatings, the existing pipeline or any annular filler.
ISO 11297-1:2013 gives the general requirements common to all relevant renovation techniques.
|
Withdrawn |
2013-05 |
Edition : 1 |
Number of pages : 15 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11297-1:2018 |
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 1: General |
ISO 11297-1:2018 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground drainage and sewerage networks under pressure, including both hydraulically and pneumatically pressurized systems. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is not applicable to the existing pipeline or any non-structural sprayed coatings or annular filler.
ISO 11297-1:2018 gives the general requirements co
|
Published |
2018-03 |
Edition : 2 |
Number of pages : 16 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11297-2:2018 |
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 2: Lining with continuous pipes |
ISO 11297-2:2018, in conjunction with ISO 11297‑1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground drainage and sewerage networks under pressure. It is applicable to polyethylene (PE) pipes of three different types:
- PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes;
- PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating;
- PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe ("coated pipe"), see Annex A.
In addition, ISO 11297-2:2018 covers:
- jointing of pipe lengths by means of butt fusion;
- fabricated and injection-moulded fittings made of PE.
ISO 11297-2:2018 is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature.
NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427‑1:2007, Annex A.
|
Published |
2018-02 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11297-3:2013 |
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 3: Lining with close-fit pipes |
ISO 11297-3:2013, in conjunction with ISO 11297-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipe for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.
|
Withdrawn |
2013-06 |
Edition : 1 |
Number of pages : 15 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 13264:2010 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics fittings — Test method for mechanical strength or flexibility of fabricated fittings |
ISO 13264:2010 specifies a method for testing the mechanical strength or flexibility of a fabricated thermoplastic fitting intended to be used in non-pressure underground applications.
|
Published |
2010-06 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11297-3:2018 |
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 3: Lining with close-fit pipes |
This document, in conjunction with ISO 11297‑1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure.
It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner, as well as associated fittings and joints for the construction of the lining system. It is not applicable to PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe.
It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature.
NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427‑1:2007, Annex A.
|
Published |
2018-09 |
Edition : 2 |
Number of pages : 16 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 11297-4:2018 |
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 4: Lining with cured-in-place pipes |
ISO 11297-4:2018, in conjunction with ISO 11297‑1 and ISO 11296‑4, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of hydraulically and pneumatically pressurized underground drainage and sewerage networks with service temperatures up to 50 °C.
ISO 11297-4:2018 applies to independent (fully structural, class A) and interactive (semi structural, class B) pressure pipe liners, as defined in ISO 11295, which do not rely on adhesion to the existing pipeline.
ISO 11297-4:2018 applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials, reinforcement, and other process-related plastics components (see 5.1).
ISO 11297-4:2018 does not include requirements or test methods for resistance to abrasion, cyclic loading or impact, which are outside the scope of this document.
|
Published |
2018-02 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 13260:2010 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Test method for resistance to combined temperature cycling and external loading |
ISO 13260:2010 specifies two methods for testing pipes and fittings or joints for plastics piping systems intended for use in underground drainage and sewerage systems for their resistance to deformation and leakage, when subjected to sustained external loading in conjunction with the passage of hot water.
|
Published |
2010-06 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 13260:2010/Amd 1:2017 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Test method for resistance to combined temperature cycling and external loading — Amendment 1 |
|
Published |
2017-08 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 13262:2010 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics spirally-formed structured-wall pipes — Determination of the tensile strength of a seam |
ISO 13262:2010 specifies a method for determining the tensile strength of a seam in a spirally-formed thermoplastics pipe. It is applicable to all such thermoplastics pipes, regardless of their intended use
|
Published |
2010-05 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 13263:2010 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics fittings — Test method for impact strength |
ISO 13263:2010 specifies a method for testing the impact resistance of fittings by dropping them on to a rigid surface. For a fitting with seal-retaining components, such as seal-retaining caps or rings, the method includes assessment of the watertightness of the fittings when the fixing elements show disturbance as a result of the test.
It is applicable to fittings made from thermoplastics materials intended to be used for buried and above-ground applications.
|
Published |
2010-05 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO/DIS 5665 |
Consumer incident investigation — Requirements and guidance |
|
Under development |
|
Edition : 1 |
Number of pages : 37 |
Technical Committee |
03.080.30
Services for consumers
|
| ISO 13265:2010 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Joints for buried non-pressure applications — Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure |
ISO 13265:2010 specifies a method for the determination of the long-term sealing pressure of elastomeric seals in assembled joints for buried non-pressure sewerage plastics piping and ducting systems.
|
Published |
2010-05 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO/DIS 13265 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Joints for buried non-pressure applications — Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure |
ISO 13265:2010 specifies a method for the determination of the long-term sealing pressure of elastomeric seals in assembled joints for buried non-pressure sewerage plastics piping and ducting systems.
|
Under development |
|
Edition : 2 |
Number of pages : 13 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 13266:2010 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics shafts or risers for inspection chambers and manholes — Determination of resistance against surface and traffic loading |
ISO 13266:2010 specifies a method of testing the resistance of the upper assembly of inspection chambers and manhole components against surface and traffic loading.
It is not applicable to requirements for testing the cover and frame.
|
Withdrawn |
2010-05 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 13266:2022 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics shafts or risers for inspection chambers and manholes — Determination of resistance against surface and traffic loading |
This document specifies a method of testing the resistance of the upper assembly of inspection chambers and manhole components against surface and traffic loading.
It is not applicable to requirements for testing the cover and frame. Those requirements are specified in EN 124-1 or other standards, depending on the material.
NOTE Upper assembly components normally include shafts or risers, cones, telescopic adapters and near surface components.
|
Published |
2022-06 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 13267:2010 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics inspection chamber and manhole bases — Test methods for buckling resistance |
ISO 13267:2010 specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.
|
Withdrawn |
2010-05 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 13267:2022 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics inspection chamber and manhole bases — Test methods for buckling resistance |
This document specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.
|
Published |
2022-06 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 13268:2010 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics shafts or risers for inspection chambers and manholes — Determination of ring stiffness |
ISO 13268:2010 specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.
|
Withdrawn |
2010-06 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 13268:2022 |
Thermoplastics piping systems for non-pressure underground drainage and sewerage — Thermoplastics shafts or risers for inspection chambers and manholes — Determination of ring stiffness |
This document specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.
|
Published |
2022-06 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 13272:2011 |
Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifiers (PP-MD) and polyethylene (PE) — Specifications for manholes and inspection chambers in traffic areas and underground installations |
ISO 13272:2011 specifies the definitions and requirements for buried manholes and inspection chambers (circular or non-circular) installed to a maximum depth of 6 m from ground level to the invert of the main chamber and manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifiers (PP-MD) or polyethylene (PE). These products are intended for use in traffic areas and underground installations conforming to the general requirements given in EN 476 and are used outside the building structure (application area code "U"). They are therefore marked accordingly with a "U".
ISO 13272:2011 is only applicable to those chamber/manhole items where the manufacturer has clearly stated in the documentation how the components shall be assembled to create a complete manhole or inspection chamber.
The inspection chambers covered by ISO 13272:2011 comprise the following:
inspection chambers providing access to the drainage or sewerage system by means of inspection and cleaning equipment;
chambers designated as manholes providing man access to the drainage or sewerage system.
|
Published |
2011-10 |
Edition : 1 |
Number of pages : 20 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 16611:2017 |
Plastics piping systems for drainage and sewerage without pressure — Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resins (UP) — Dimensions, requirements and tests |
ISO 16611:2017 specifies the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage without pressure including culverts.
It is the responsibility of the purchaser or specifier to make the appropriate selections taking into account their particular requirements and any relevant national regulations and installation practices or codes.
ISO 16611:2017 is applicable to non-circular GRP-UP pipes, with flexible or rigid joints, primarily intended for use in buried installations but may also be used to reline existing non-circular pipe lines.
NOTE 1 GRP-UP includes pipes with vinyl ester liners or made entirely from vinyl ester.
NOTE 2 Piping systems conforming to ISO 16611:2017 can be used also for non-buried applications provided the influence of the environment, e.g. from UV-radiation, and the supports are considered in the design of the pipes, fittings and joints.
ISO 16611:2017 is applicable to pipes, fittings and their joints of nominal sizes from DN 150 to DN 4000, which are intended to be used for the conveyance of surface water or sewage at temperatures up to 50 °C.
|
Published |
2017-06 |
Edition : 1 |
Number of pages : 25 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO/TS 17902:2016 |
Wrapped electrofoaming joints for polyethylene (PE) piping systems with smooth outer wall for gravity drains and sewers |
ISO/TS 17902:2016 specifies the definitions and requirements for wrapped electrofoaming joints for polyethylene (PE) piping systems with smooth outer wall for underground drains and sewer without pressure.
ISO/TS 17902:2016 specifies product range, material characteristics, test methods and test parameters, dimension and characteristics of wrap.
ISO/TS 17902:2016 is applicable to jointing pipes which have external wall thickness greater than 1,4 mm and a diameter up to DN/OD 2000, or DN/ID 2200.
|
Published |
2016-11 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 18672-1:2009 |
Plastics piping systems for non-pressure drainage and sewerage — Polyester resin concrete (PRC) — Part 1: Pipes and fittings with flexible joints |
ISO 18672-1:2009 specifies definitions, requirements and characteristics of pipes, fittings, joints, materials, test methods and marking for pipes and fittings made from polyester resin concrete (PRC), intended to be used within a drain or sewer system operating without pressure. It applies to products for use in buried installations to be installed by open-trench techniques or pipe jacking.
It applies to pipes, fittings and their joints of nominal sizes from DN 150 to DN 3000 for circular cross-sections, from WN/HN 300/450 to WN/HN 1400/2100 for egg-shaped cross-sections and from DN 800 to DN 1800 for kite-shaped cross-sections.
|
Published |
2009-06 |
Edition : 1 |
Number of pages : 68 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO/DIS 24511 |
Activities relating to drinking water and wastewater services — Guidelines for the management of wastewater utilities and for the assessment of wastewater services |
|
Under development |
|
Edition : 2 |
Number of pages : 58 |
Technical Committee |
93.030
External sewage systems
;
03.080.30
Services for consumers
;
13.060.30
Sewage water
|
| ISO 21138-1:2007 |
Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 1: Material specifications and performance criteria for pipes, fittings and system |
ISO 21138-1:2007 specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems in the field of non-pressure underground systems for underground drainage and sewerage.
ISO 21138-1:2007 specifically refers to PVC, PP and PE materials.
ISO 21138-1:2007 covers a range of pipe and fitting sizes, materials, pipe constructions, nominal ring stiffnesses, and gives recommendations concerning colours.
In conjunction with ISO 21138-2 and ISO 21138-3, it is applicable to PVC-U, PP and PE structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for the transport of drainage and sewerage.
ISO 21138-1:2007 is applicable to PVC-U, PP and PE structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
For dimensions larger than DN/OD 1200 or DN/ID 1200, ISO 21138-1:2007 can serve as a general guide regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.
|
Withdrawn |
2007-10 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 21138-1:2020 |
Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 1: Material specification and performance criteria for pipes, fittings and systems |
This document, together with ISO 21138‑2 and ISO 21138‑3, specifies the definitions and requirements for pipes, fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems intended to be used in non-pressure underground drainage and sewerage applications.
NOTE 1 Pipes, fittings and the system complying with this document can also be used for highway drainage and surface water.
This document covers a range of pipe and fitting sizes, materials, pipe constructions, nominal ring stiffnesses, and gives recommendations concerning colours.
NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes.
In conjunction with ISO 21138‑2 and ISO 21138‑3, this document is applicable to structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials.
It is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
NOTE 3 Pipes, fittings and other components conforming to any plastics product standards referred to in the Bibliography can be used with pipes and fittings conforming to this document when they conform to the requirements for joint dimensions given in ISO 21138-2 and ISO 21138-3 and to the performance requirements given in Clause 9.
NOTE 4 For dimensions larger than DN/OD 1200 or DN/ID 1200, this document can serve as a general guideline regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.
|
Published |
2020-01 |
Edition : 2 |
Number of pages : 17 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 21138-2:2007 |
Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 2: Pipes and fittings with smooth external surface, Type A |
ISO 21138-2:2007, together with ISO 21138-1, specifies the definitions and requirements for pipes with a smooth external surface (Type A), fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping in the field of non-pressure systems for underground drainage and sewerage.
ISO 21138-2:2007 specifically refers to PVC, PP and PE materials
ISO 21138-2:2007 specifies test methods and test parameters.
ISO 21138-2:2007 covers a range of pipe and fitting sizes, materials, pipe constructions, and nominal ring stiffnesses, and gives recommendations concerning colours.
In conjunction with ISO 21138-1, it is applicable to PVC-U, PP and PE structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for the transport of drainage and sewage.
ISO 21138-2:2007 is applicable to PVC-U, PP and PE structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
|
Withdrawn |
2007-10 |
Edition : 1 |
Number of pages : 41 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 21138-2:2020 |
Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 2: Pipes and fittings with smooth external surface, Type A |
This document, together with ISO 21138-1, specifies the definitions and requirements for pipes with smooth external and internal surfaces (Type A), fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems intended to be used in non-pressure underground drainage and sewerage applications.
NOTE 1 Pipes, fittings and the system complying with this document can also be used for highway drainage and surface water.
This document specifies test methods and test parameters.
This document covers a range of pipe and fitting sizes, materials, pipe constructions and nominal ring stiffnesses, and gives recommendations concerning colours.
NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes.
In conjunction with ISO 21138-1, this document is applicable to structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials.
It is applicable to pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
NOTE 3 For dimensions larger than DN/OD 1200, or DN/ID 1200, this document can serve as general guidance regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.
Test methods are not included in this document.
|
Published |
2020-01 |
Edition : 2 |
Number of pages : 39 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 7675:1991 |
Chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings for soil and waste discharge (low and high temperature) systems inside buildings — Specifications |
|
Withdrawn |
1991-05 |
Edition : 1 |
Number of pages : 19 |
Technical Committee |
83.140.30
Plastics pipes and fittings for non fluid use
;
91.140.80
Drainage systems
|
| ISO 21138-3:2007 |
Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 3: Pipes and fittings with non-smooth external surface, Type B |
ISO 21138-3:2007, together with ISO 21138-1, specifies the definitions and requirements for pipes with a non-smooth external surface (Type B), fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems in the field of non-pressure systems for underground drainage and sewerage.
ISO 21138-3:2007 specifically refers to PVC, PP and PE materials.
ISO 21138-3:2007 specifies test methods and test parameters.
ISO 21138-3:2007 covers a range of pipe and fitting sizes, materials, pipe constructions and nominal ring stiffnesses, and gives recommendations concerning colours.
In conjunction with ISO 21138-1, it is applicable to PVC-U, PP and PE structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for the transport of drainage and sewage.
ISO 21138-3:2007 is applicable to PVC-U, PP and PE structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
|
Withdrawn |
2007-10 |
Edition : 1 |
Number of pages : 39 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO 21138-3:2020 |
Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 3: Pipes and fittings with non-smooth external surface, Type B |
This document, together with ISO 21138‑1, specifies the definitions and requirements for pipes with a non-smooth external surface and a smooth internal surface (Type B), fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems intended to be used in non-pressure underground drainage and sewerage applications.
NOTE 1 Pipes, fittings and the systems complying with this document can also be used for highway drainage and surface water.
This document specifies test methods and test parameters.
This document covers a range of pipe and fitting sizes, materials, pipe constructions and nominal ring stiffnesses, and gives recommendations concerning colours.
NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and installation practices or codes.
In conjunction with ISO 21138‑1, this document is applicable to structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials.
It is applicable to pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
NOTE 3 Pipes, fittings and other components conforming to any plastics product standards referred to in Clause 2 are deemed to be suitable for use with pipes and fittings conforming to this document, when they conform to the requirements for joint dimensions given in ISO 21138‑2 or ISO 21138‑3 (this document) and to the performance requirements given in Clause 10.
NOTE 4 For dimensions larger than DN/OD 1200 or DN/ID 1200, this document can serve as general guidance regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.
Test methods are not included in this document.
|
Published |
2020-01 |
Edition : 2 |
Number of pages : 38 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
;
91.140.80
Drainage systems
|
| ISO/DIS 23627 |
Plastics piping systems for non-pressure underground drainage and sewerage – Steel-Reinforced-Polyethylene (SRPE) - Corrugated Pipes and fittings |
|
Deleted |
|
Edition : 1 |
Number of pages : 54 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
23.040.45
Plastics fittings
|
| ISO 23856:2021 |
Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin |
This document specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of water supply, drainage and sewerage with or without pressure. Types of water supply include, but are not limited to, raw water, irrigation, cooling water, potable water, salt water, sea water, penstocks in power plants, processing plants and other water-based applications. This document is applicable to GRP UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in direct buried installations.
NOTE 1 For the purpose of this document, the term polyester resin (UP) also includes vinyl-ester resins (VE).
NOTE 2 Piping systems conforming to this document can also be used for non-buried applications, provided the influence of the environment and the supports are considered in the design of the pipes, fittings and joints.
NOTE 3 This document can also apply for other installations, such as slip-lining rehabilitation of existing pipes.
NOTE 4 ISO 10467 and ISO 10639, which are replaced by this document, are also referenced in ISO 25780, which specifies requirements for GRP-pipes used for jacking installation.
The requirements for the hydrostatic pressure design of pipes referring to this document meet the requirements of ISO/TS 20656-1 and the general principle for the reliability of structures detailed in ISO 2394 and in EN 1990. These International Standards provide procedures for the harmonization of design practices and address the probability of failure, as well as possible consequences of failures. The design practices are based on a partial safety factor concept, as well as on risk management engineering.
This document is applicable to circular pipes, fittings and their joints of nominal sizes from DN 50 to DN 4000, which are intended to be used for the conveyance of water, sewage and drainage at normal service conditions, with or without pressure.
|
Published |
2021-06 |
Edition : 1 |
Number of pages : 60 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
91.140.80
Drainage systems
|
| ISO 24511:2007 |
Activities relating to drinking water and wastewater services — Guidelines for the management of wastewater utilities and for the assessment of wastewater services |
ISO 24511:2007 provides guidelines for the management of wastewater utilities and for the assessment of wastewater services.
ISO 24511:2007 is applicable to publicly and privately owned and operated wastewater utilities, but does not favour any particular ownership or operational model.
ISO 24511:2007 addresses wastewater systems in their entirety and is applicable to systems at any level of development (e.g. pit latrines, on-site systems, networks, treatment facilities).
The following are within the scope of ISO 24511:2007:
the definition of a language common to different stakeholders;
objectives for the wastewater utility;
guidelines for the management of wastewater utilities;
service assessment criteria and related examples of performance indicators, all without setting any target values or thresholds.
|
Published |
2007-12 |
Edition : 1 |
Number of pages : 59 |
Technical Committee |
93.030
External sewage systems
;
13.060.30
Sewage water
|
| ISO 13351:2009 |
Fans — Dimensions |
ISO 13351:2009 specifies the dimensions of the circular and rectangular flanges of general‑purpose fans, as well as the fan size designations. It is not applicable to cross‑flow fans or to fan appliances used for individual household or similar applications.
|
Published |
2009-11 |
Edition : 2 |
Number of pages : 13 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 25780:2011 |
Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Pipes with flexible joints intended to be installed using jacking techniques |
ISO 25780:2011 specifies the properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) for water supply, irrigation, drainage or sewerage systems with or without pressure.
ISO 25780:2011 is applicable to GRP-UP piping systems, with flexible joints, intended to be installed using jacking techniques. It specifies the characteristics of pipes made from GRP-UP, with or without aggregates or fillers and also specifies the test parameters for the test methods referred to in ISO 25780:2011.
ISO 25780:2011 is applicable to pipes and joints with a size range from DN100 to DN4000 which are intended to be used for the conveyance of water or sewage at temperatures up to 50ºC, with or without pressure.
ISO 25780:2011 covers requirements to improve the design of the joint and specifies type test performance requirements for the joints as a function of the declared nominal pressure rating of the pipeline system and the required joint deflection capability of the system.
|
Published |
2011-05 |
Edition : 1 |
Number of pages : 51 |
Technical Committee |
93.030
External sewage systems
;
23.040.20
Plastics pipes
;
91.140.60
Water supply systems
;
91.140.80
Drainage systems
|
| ISO 5667-10:1992 |
Water quality — Sampling — Part 10: Guidance on sampling of waste waters |
Contains details on the sampling of domestic and industrial waste water, i.e. the design of sampling programmes and techniques for collection of samples including safety aspects. Covers waste water in all its forms. Sampling of accidental spillages is not included, although the methods described in certain cases may also be applicable to spillages.
|
Withdrawn |
1992-11 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
13.060.30
Sewage water
|
| ISO 5667-10:2020 |
Water quality — Sampling — Part 10: Guidance on sampling of waste water |
This document contains details on the sampling of domestic and industrial waste water, i.e. the design of sampling programmes and techniques for the collection of samples. It covers waste water in all its forms, i.e. industrial waste water, radioactive waste water, cooling water, raw and treated domestic waste water.
It deals with various sampling techniques used and the rules to be applied so as to ensure the samples are representative.
Sampling of accidental spillages is not included, although the methods described in certain cases may also be applicable to spillages.
|
Published |
2020-11 |
Edition : 2 |
Number of pages : 45 |
Technical Committee |
13.060.30
Sewage water
|