| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO 3952-3:1979 |
Kinematic diagrams — Graphical symbols |
The symbols system is intended for simplifying the preparation of diagrams of products in all branches of industry and is to be used in technical documentation as well as in technical and educational literature. It will facilitate the execution and understanding of such diagrams by specialists of different countries. This part contains Geneva and ratchet mechanisms as well as couplings and brakes.
|
Published |
1979-12 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
21.020
Characteristics and design of machines, apparatus, equipment
;
01.080.30
Graphical symbols for use on mechanical engineering and construction drawings, diagrams, plans, maps and in relevant technical product documentation
|
| ISO 3952-4:1984 |
Kinematic diagrams — Graphical symbols |
The symbols system is intended for simplifying the preparation of diagrams of products in all branches of industry and is to be used in technical documentation as well as in technical and educational literature. It will facilitate the execution and understanding of such diagrams by specialists of different countries. This part contains miscellaneous mechanisms and their components.
|
Published |
1984-07 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
21.020
Characteristics and design of machines, apparatus, equipment
;
01.080.30
Graphical symbols for use on mechanical engineering and construction drawings, diagrams, plans, maps and in relevant technical product documentation
|
| ISO 4871:1984 |
Acoustics — Noise labelling of machinery and equipment |
|
Withdrawn |
1984-08 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
21.020
Characteristics and design of machines, apparatus, equipment
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 4871:1996 |
Acoustics — Declaration and verification of noise emission values of machinery and equipment |
Gives information on the declaration of noise emission values, decribes acoustical information to be presented in technical documents and specifies a method for verifying the noise emission declaration. Replaces the first edition.
|
Published |
1996-12 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
21.020
Characteristics and design of machines, apparatus, equipment
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 10816-3:1998 |
Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 3: Industrial machines with nominal power above 15 kW and nominal speeds between 120 r/min and 15 000 r/min when measured in situ |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
17.160
Vibrations, shock and vibration measurements
;
21.020
Characteristics and design of machines, apparatus, equipment
|
| ISO 10816-3:2009 |
Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 3: Industrial machines with nominal power above 15 kW and nominal speeds between 120 r/min and 15 000 r/min when measured in situ |
ISO 10816-3:2009 gives criteria for assessing vibration measurements when made in situ. The criteria specified apply to machine sets having a power above 15 kW and operating speeds between 120 r/min and 15 000 r/min.
|
Withdrawn |
2009-02 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
17.160
Vibrations, shock and vibration measurements
;
21.020
Characteristics and design of machines, apparatus, equipment
|
| ISO 10816-3:2009/Amd 1:2017 |
Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 3: Industrial machines with nominal power above 15 kW and nominal speeds between 120 r/min and 15 000 r/min when measured in situ — Amendment 1 |
|
Withdrawn |
2017-08 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
17.160
Vibrations, shock and vibration measurements
;
21.020
Characteristics and design of machines, apparatus, equipment
|
| ISO/TR 11688-1:1995 |
Acoustics — Recommended practice for the design of low-noise machinery and equipment — Part 1: Planning |
Serves as an aid to understanding the basic concepts of noise control in machinery and equipment. The recommended practice presented is intended to assist the designer at any design stage to control the noise of the final product. Makes references to numerous technical publications dealing with acoustical problems.
|
Published |
1995-03 |
Edition : 1 |
Number of pages : 25 |
Technical Committee |
21.020
Characteristics and design of machines, apparatus, equipment
;
17.140.20
Noise emitted by machines and equipment
|
| ISO/TR 11688-2:1998 |
Acoustics — Recommended practice for the design of low-noise machinery and equipment — Part 2: Introduction to the physics of low-noise design |
|
Published |
1998-09 |
Edition : 1 |
Number of pages : 46 |
Technical Committee |
21.020
Characteristics and design of machines, apparatus, equipment
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 12100-2:2003/Amd 1:2009 |
Safety of machinery — Basic concepts, general principles for design — Part 2: Technical principles — Amendment 1 |
|
Withdrawn |
2009-06 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
13.110
Safety of machinery
|
| ISO Guide 78:2008 |
Safety of machinery — Rules for drafting and presentation of safety standards |
ISO Guide 78:2008 presents rules for the drafting and presentation of International Standards dealing with machinery safety and safety components and their revisions, primarily to achieve consistency and acceptable quality of the various standards to be prepared.
It also gives requirements on the criteria for the selection of new work items and for procedures to prepare, produce or revise standards in an efficient and effective way.
ISO Guide 78:2008 gives requirements that are additional to the ISO/IEC Directives, Part 2, when this is necessary owing to the special requirements of machinery safety standards and standards for safety components.
ISO Guide 78:2008 is primarily intended for the drafting of type-C standards. It is also applicable to the drafting of type-B standards; however, the foreseeable variation in the format of these standards prevents general application. When its requirements are specific to type-B standards, this is indicated.
|
Withdrawn |
2008-04 |
Edition : 1 |
Number of pages : 21 |
Technical Committee |
01.120
Standardization. General rules
;
13.110
Safety of machinery
|
| ISO Guide 78:2012 |
Safety of machinery — Rules for drafting and presentation of safety standards |
|
Published |
2012-12 |
Edition : 2 |
Number of pages : 21 |
Technical Committee |
01.120
Standardization. General rules
;
13.110
Safety of machinery
|
| ISO/CD 6909 |
Machine tools Safety — Press brakes |
This document specifies technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of press brakes which are intended to work cold metal or material partly of cold metal but which can be used in the same way to work other sheet materials (e.g. cardboard, plastic, rubber, leather, etc.) and also referred to as machines.
NOTE 1 The design of a machine includes the study of the machine itself, taking into account all phases of the “life” of the machine mentioned in ISO 12100:2010, 5.4, and the drafting of the instructions related to all the above phases.
This document covers the following types of machines (see Annex J) :
- Hydraulic press brakes
- Hydraulic servo-drive press brakes
- Screw servo-drive press brakes
- Belt-spring servo-drive press brakes
The requirements in this document take account of intended use, as defined in ISO 12100:2010, 3.23, as well as reasonably foreseeable misuse, as defined in ISO 12100:2010, 3.24. This document presumes access to the press brake from all directions, deals with all significant hazards during the various phases of the life of the machine described in Clause 4, and specifies the safety measures for both the operator and other exposed persons.
NOTE 2 All significant hazards means those identified or associated with press brakes at the time of the publication of this document.
This document applies to press brakes which can function independently or in combination (e.g. two machines in tandem or more) and can also be used as a guide for the design of press brakes which are intended to be integrated in a manufacturing system.
This document deals with the significant hazards, hazardous situations and events relevant to press brakes and ancillary devices (see Clause 4). This document specifies the safety requirements for press brakes defined in this clause.
This document does not cover press brakes which transmit energy to impart beam motion by using pneumatic means or mechanical clutch or press brakes that use combination of technologies (e.g. combined hydraulic and screw servo-drive press brake or combined hydraulic servo-drive and screw servo-drive press brake)
This document does not cover machines whose principal designed purpose is:
a) sheet folding by rotary action;
b) tube and pipe bending by rotary action;
c) roll bending.
This document does not cover hazards related to the use of press brakes in explosive atmospheres.
This document is not applicable to press brakes which are manufactured before the date of its publication.
This document does not cover the safety aspect of equipment for automatic loading and unloading where provided. Guidance on how to take into account additional automatic loading and unloading equipment can be found in ISO 11161.
|
Under development |
|
Edition : 1 |
|
Technical Committee |
13.110
Safety of machinery
;
25.080.01
Machine tools in general
|
| ISO 11161:2007 |
Safety of machinery — Integrated manufacturing systems — Basic requirements |
ISO 11161:2007 specifies the safety requirements for integrated manufacturing systems (IMS) that incorporate two or more interconnected machines for specific applications, such as component manufacturing or assembly. It gives requirements and recommendations for the safe design, safeguarding and information for the use of such IMSs.
ISO 11161:2007 is not intended to cover safety aspects of individual machines and equipment that may be covered by standards specific to those machines and equipment. Therefore it deals only with those safety aspects that are important for the safety-relevant interconnection of the machines and components. Where machines and equipment of an integrated manufacturing system are operated separately or individually, and while the protective effects of the safeguards provided for production mode are muted or suspended, the relevant safety standards for these machines and equipment apply.
|
Published |
2007-05 |
Edition : 2 |
Number of pages : 36 |
Technical Committee |
13.110
Safety of machinery
;
25.040.01
Industrial automation systems in general
|
| ISO 11161:2007/Amd 1:2010 |
Safety of machinery — Integrated manufacturing systems — Basic requirements — Amendment 1 |
|
Published |
2010-03 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
13.110
Safety of machinery
;
25.040.01
Industrial automation systems in general
|
| ISO/DIS 11161 |
Safety of machinery — Integration of machinery into a system — Basic requirements |
This document specifies the safety requirements for the integration of machinery into a system. It gives requirements and recommendations for inherently safe design, safeguarding and information for the use of an IMS. This document is not intended to cover safety aspects of individual machines and equipment that can be covered by standards specific to those machines and equipment. Therefore, it deals only with those safety aspects that are important for the safety-relevant interconnection of the machines and components. Where component machines of an integrated machinery system are operated separately or individually, the safety requirements of the relevant safety standards for these machines and equipment apply. This document is also applicable when a modification of an existing IMS results in a new configuration, function, capability or location.
|
Under development |
|
Edition : 3 |
Number of pages : 69 |
Technical Committee |
13.110
Safety of machinery
;
25.040.01
Industrial automation systems in general
|
| ISO 13849-1:2006/Cor 1:2009 |
Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design — Technical Corrigendum 1 |
|
Withdrawn |
2009-02 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 11553-1:2005 |
Safety of machinery — Laser processing machines — Part 1: General safety requirements |
ISO 11553-1:2005 describes hazards generated by laser processing machines, and specifies the safety requirements relating to radiation hazards and hazards generated by materials and substances. It also specifies the information to be supplied by the manufacturers of such equipment.
Requirements dealing with noise as a hazard from laser processing machines are not included in ISO 11553-1:2005. They will be included in a subsequent amendment.
ISO 11553-1:2005 is not applicable to laser products, or equipment containing such products, which are manufactured solely and expressly for the following applications: photolithography, stereolithography, holography, medical applications and data storage.
|
Withdrawn |
2005-02 |
Edition : 1 |
Number of pages : 16 |
Technical Committee |
13.110
Safety of machinery
;
31.260
Optoelectronics. Laser equipment
|
| ISO 11553-1:2020 |
Safety of machinery — Laser processing machines — Part 1: Laser safety requirements |
This document describes laser radiation hazards arising in laser processing machines, as defined in 3.7. It also specifies the safety requirements relating to laser radiation hazards, as well as the information to be supplied by the manufacturers of such equipment (in addition to that prescribed by IEC 60825).
Requirements dealing with noise as a hazard from laser processing machines are included in ISO 11553‑3:2013.
This document is applicable to machines using laser radiation to process materials.
It is not applicable to laser products, or equipment containing such products, which are manufactured solely and expressly for the following applications:
— photolithography;
— stereolithography;
— holography;
— medical applications (per IEC 60601-2-22);
— data storage.
|
Published |
2020-04 |
Edition : 2 |
Number of pages : 22 |
Technical Committee |
13.110
Safety of machinery
;
31.260
Optoelectronics. Laser equipment
|
| ISO 11553-2:2007 |
Safety of machinery — Laser processing machines — Part 2: Safety requirements for hand-held laser processing devices |
ISO 11553-2:2007 specifies the requirements for laser processing devices, as defined in ISO 11553-1, which are hand-held or hand-operated.
The purpose of ISO 11553-2:2007 is to draw attention to the particular hazards related to the use of hand-held laser and hand-operated laser processing devices and to prevent personal injury. This includes both the areas of hazard analysis and risk assessment as well as protective measures.
|
Published |
2007-03 |
Edition : 1 |
Number of pages : 20 |
Technical Committee |
13.110
Safety of machinery
;
31.260
Optoelectronics. Laser equipment
|
| ISO 11553-3:2013 |
Safety of machinery — Laser processing machines — Part 3: Noise reduction and noise measurement methods for laser processing machines and hand-held processing devices and associated auxiliary equipment (accuracy grade 2) |
ISO/IEC 11553-3:2013 describes the requirements to deal with noise hazards and specifies all the information necessary to carry out efficiently and under standardized conditions the determination, declaration and verification of airborne noise emission from laser processing machines and hand-held laser processing devices within the scope of ISO/IEC 11553-1 and ISO/IEC 11553-2. It specifies the safety requirements relating to noise hazards. It specifies noise measurement methods, installation and operating conditions to be used for the test, together with the information to be supplied by manufacturers of such equipment.
ISO/IEC 11553-3:2013 applies to those laser processing machines and hand-held laser processing devices included in the scope of ISO/IEC 11553-1 and ISO/IEC 11553-2.
Noise emission characteristics include emission sound pressure levels at work stations and the sound power level. Declared noise emission values permit comparison of laser processing machines and hand-held laser processing devices on the market.
The use of this noise test code (see Annex A) ensures the reproducibility of the determination of the characteristic noise emission values within specific limits. These limits are determined by the accuracy grade of the noise emission measuring method used. Noise emission measurements specified by ISO/IEC 11553-3:2013 meet the requirements of an engineering method (accuracy grade 2).
|
Published |
2013-03 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
13.110
Safety of machinery
;
31.260
Optoelectronics. Laser equipment
|
| ISO 12100-1:2003 |
Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology, methodology |
ISO 12100-1:2003 defines basic terminology and methodology used in achieving safety of machinery.
The provisions stated are intended for the designer.
The standard does not deal with damage to domestic animals, property or the environment.
|
Withdrawn |
2003-11 |
Edition : 1 |
Number of pages : 33 |
Technical Committee |
13.110
Safety of machinery
;
01.040.13
Environment. Health protection. Safety (Vocabularies)
|
| ISO/TR 12100-1:1992 |
Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology, methodology |
The document defines basic terminology and specifies general design methods, to help designers and manufacturers in achieving safety in the design of machinery for professional and non-professional purposes.
|
Withdrawn |
1992-12 |
Edition : 1 |
Number of pages : 37 |
Technical Committee |
13.110
Safety of machinery
;
01.040.13
Environment. Health protection. Safety (Vocabularies)
|
| ISO 12100-1:2003/Amd 1:2009 |
Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology, methodology — Amendment 1 |
|
Withdrawn |
2009-06 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
13.110
Safety of machinery
;
01.040.13
Environment. Health protection. Safety (Vocabularies)
|
| ISO 12100-2:2003 |
Safety of machinery — Basic concepts, general principles for design — Part 2: Technical principles |
ISO 12100-2:2003 defines technical principles to help designers in achieving safety in the design of machinery.
It does not deal with damage to domestic animals, property or the environment.
|
Withdrawn |
2003-11 |
Edition : 1 |
Number of pages : 32 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 12100:2010 |
Safety of machinery — General principles for design — Risk assessment and risk reduction |
ISO 12100:2010 specifies basic terminology, principles and a methodology for achieving safety in the design of machinery. It specifies principles of risk assessment and risk reduction to help designers in achieving this objective. These principles are based on knowledge and experience of the design, use, incidents, accidents and risks associated with machinery. Procedures are described for identifying hazards and estimating and evaluating risks during relevant phases of the machine life cycle, and for the elimination of hazards or sufficient risk reduction. Guidance is given on the documentation and verification of the risk assessment and risk reduction process.
ISO 12100:2010 is also intended to be used as a basis for the preparation of type-B or type-C safety standards.
It does not deal with risk and/or damage to domestic animals, property or the environment.
|
Published |
2010-11 |
Edition : 1 |
Number of pages : 77 |
Technical Committee |
13.110
Safety of machinery
|
| ISO/CD 12895 |
Safety of machinery — Identification of whole body access and prevention of derived risks |
This document establishes the criteria to evaluate when whole body access exists in a machinery application and includes appropriate risk reduction measures to minimize or reduce associated risks. It provides a methodology to determine the selection of risk reduction measures when whole body access exists.
This document assumes separation distances have been applied according to ISO 13855 and ISO 13857.
Protection against the risks from hazards arising from emissions (e.g., the ejection of solid or fluid materials, radiation, electric arcs, heat, noise, fumes, gases) are not entirely covered by this document, although the application of the proposed risk reduction measures may minimize or reduce them.
Protection against the risks from hazards arising from breaking of parts of the machine or gravity falls, are not covered by this document.
This document applies for safeguards used on machinery for the protection of persons 14 years and older.
|
Under development |
|
Edition : 1 |
|
Technical Committee |
13.110
Safety of machinery
|
| ISO 13105-2:2014 |
Building construction machinery and equipment — Machinery for concrete surface floating and finishing — Part 2: Safety requirements and verification |
ISO 13105-2:2014 specifies safety requirements for machines used for concrete surface floating and finishing. This includes pedestrian-controlled equipment and ride-on equipment. It is not applicable to internal or external vibrators or ancillary equipment used with internal and external vibrators, for example, air compressors, hydraulic power sources, and voltage transformers, to remote-controlled or hand-held smoothing machines and self-acting (robotic) smoothing machines, or to strike-off type machines commonly known as screeds.
It deals with significant hazards, hazardous situations, or hazardous events relevant to machinery for concrete surface floating and finishing (power trowels) when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
It is not applicable to machines which are manufactured before the date of its publication.
|
Published |
2014-12 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
13.110
Safety of machinery
;
91.220
Construction equipment
|
| ISO 13105-2:2014/Amd 1:2017 |
Building construction machinery and equipment — Machinery for concrete surface floating and finishing — Part 2: Safety requirements and verification — Amendment 1 |
|
Published |
2017-11 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
13.110
Safety of machinery
;
91.220
Construction equipment
|
| ISO/DIS 13105-2 |
Building construction machinery and equipment — Machinery for concrete surface floating and finishing — Part 2: Safety requirements and verification |
ISO 13105-2:2014 specifies safety requirements for machines used for concrete surface floating and finishing. This includes pedestrian-controlled equipment and ride-on equipment. It is not applicable to internal or external vibrators or ancillary equipment used with internal and external vibrators, for example, air compressors, hydraulic power sources, and voltage transformers, to remote-controlled or hand-held smoothing machines and self-acting (robotic) smoothing machines, or to strike-off type machines commonly known as screeds.
It deals with significant hazards, hazardous situations, or hazardous events relevant to machinery for concrete surface floating and finishing (power trowels) when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
It is not applicable to machines which are manufactured before the date of its publication.
|
Under development |
|
Edition : 2 |
Number of pages : 17 |
Technical Committee |
13.110
Safety of machinery
;
91.220
Construction equipment
|
| ISO 13849-1:1999 |
Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
|
Withdrawn |
1999-11 |
Edition : 1 |
Number of pages : 31 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13849-1:2006 |
Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
ISO 13849-1:2006 provides safety requirements and guidance on the principles for the design and integration of safety-related parts of control systems (SRP/CS), including the design of software. For these parts of SRP/CS, it specifies characteristics that include the performance level required for carrying out safety functions. It applies to SRP/CS, regardless of the type of technology and energy used (electrical, hydraulic, pneumatic, mechanical, etc.), for all kinds of machinery. It does not specify the safety functions or performance levels that are to be used in a particular case.
ISO 13849-1:2006 provides specific requirements for SRP/CS using programmable electronic system(s).
It does not give specific requirements for the design of products which are parts of SRP/CS. Nevertheless, the principles given, such as categories or performance levels, can be used.
|
Withdrawn |
2006-11 |
Edition : 2 |
Number of pages : 85 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13849-1:2015 |
Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
ISO 13849-1:2015 provides safety requirements and guidance on the principles for the design and integration of safety-related parts of control systems (SRP/CS), including the design of software. For these parts of SRP/CS, it specifies characteristics that include the performance level required for carrying out safety functions. It applies to SRP/CS for high demand and continuous mode, regardless of the type of technology and energy used (electrical, hydraulic, pneumatic, mechanical, etc.), for all kinds of machinery.
It does not specify the safety functions or performance levels that are to be used in a particular case.
This part of ISO 13849 provides specific requirements for SRP/CS using programmable electronic system(s).
It does not give specific requirements for the design of products which are parts of SRP/CS. Nevertheless, the principles given, such as categories or performance levels, can be used.
NOTE 1 Examples of products which are parts of SRP/CS: relays, solenoid valves, position switches, PLCs, motor control units, two-hand control devices, pressure sensitive equipment. For the design of such products, it is important to refer to the specifically applicable International Standards, e.g. ISO 13851, ISO 13856‑1 and ISO 13856‑2.
NOTE 2 For the definition of required performance level, see 3.1.24.
NOTE 3 The requirements provided in this part of ISO 13849 for programmable electronic systems are compatible with the methodology for the design and development of safety-related electrical, electronic and programmable electronic control systems for machinery given in IEC 62061.
NOTE 4 For safety-related embedded software for components with PLr = e, see IEC 61508?3:1998, Clause 7.
|
Published |
2015-12 |
Edition : 3 |
Number of pages : 86 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13849-1 |
Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
|
Under development |
2023-04 |
Edition : 4 |
|
Technical Committee |
13.110
Safety of machinery
|
| ISO 13849-2:2003 |
Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
ISO 13849-2:2003 specifies the procedures and conditions to be followed for the validation by analysis and testing of:
the safety functions provided andthe category achieved
for the safety-related parts of the control system in compliance with EN 954-1 (ISO 13849-1), using the design rationale provided by the designer.
This International Standard does not give complete validation requirements for programmable electronic systems and therefore can require the use of other standards.
|
Withdrawn |
2003-08 |
Edition : 1 |
Number of pages : 50 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13849-2:2012 |
Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
ISO 13849-2:2012 specifies the procedures and conditions to be followed for the validation by analysis and testing of the specified safety functions, the category achieved, and the performance level achieved by the safety-related parts of a control system (SRP/CS) designed in accordance with ISO 13849-1.
|
Published |
2012-10 |
Edition : 2 |
Number of pages : 79 |
Technical Committee |
13.110
Safety of machinery
|
| ISO/TR 13849-100:2000 |
Safety of machinery — Safety-related parts of control systems — Part 100: Guidelines for the use and application of ISO 13849-1 |
|
Withdrawn |
2000-09 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13850:1996 |
Safety of machinery — Emergency stop — Principles for design |
Specifies functional requirements and design principles for the emergency stop of machinery, independent of the type of energy used to control the function.
|
Withdrawn |
1996-10 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13850:2006 |
Safety of machinery — Emergency stop — Principles for design |
ISO 13850:2006 specifies functional requirements and design principles for the emergency stop function on machinery, independent of the type of energy used to control the function. It is applicable to all machinery except for machines in which the provision of emergency stop would not lessen the risk, and hand-held portable machines and hand-guided machines. It does not deal with functions such as reversal or limitation of motion, deflection, shielding, braking or disconnecting, which can be part of the emergency stop function.
|
Withdrawn |
2006-11 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13850:2015 |
Safety of machinery — Emergency stop function — Principles for design |
ISO 13850:2015 Standard specifies functional requirements and design principles for the emergency stop function on machinery, independent of the type of energy used.
It does not deal with functions such as reversal or limitation of motion, deflection of emissions (e.g. radiation, fluids), shielding, braking or disconnecting, which can be part of the emergency stop function.
The requirements for this International Standard apply to all machines, with exception to:
- machines where an emergency stop would not reduce the risk;
- hand-held or hand-operated machines.
NOTE The requirements for the realization of the emergency stop function based on electrical/electronic technology are described in IEC 60204‑1.
|
Published |
2015-11 |
Edition : 3 |
Number of pages : 11 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13856-3:2006 |
Safety of machinery — Pressure-sensitive protective devices — Part 3: General principles for the design and testing of pressure-sensitive bumpers, plates, wires and similar devices |
ISO 13856-3:2006 gives basic requirements for those pressure-sensitive protective devices, with or without an external reset facility, that are not specified in either ISO 13856-1 or ISO 13856-2, the majority of which are produced for specific applications and are not available as off-the-shelf items. It also gives specific requirements for pressure-sensitive bumpers, pressure-sensitive plates and pressure-sensitive wires (trip wires).
|
Withdrawn |
2006-10 |
Edition : 1 |
Number of pages : 56 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 5841-1:1985 |
Implants for surgery — Cardiac pacemakers — Part 1: Implantable ventricular pacemakers |
|
Withdrawn |
1985-09 |
Edition : 1 |
|
Technical Committee |
11.040.40
Implants for surgery, prosthetics and orthotics
|
| ISO 13851:2002 |
Safety of machinery — Two-hand control devices — Functional aspects and design principles |
This International Standard specifies the safety requirements of a two-hand control device and the dependency of the output signal from the input signals.
It describes the main characteristics of two-hand control devices for the achievement of safety and sets out combinations of functional characteristics for three types. It does not apply to devices intended to be used as enabling devices, as hold-to-run devices or as special control devices.
This International Standard does not specify with which machines two-hand control devices shall be used. It also does not specify which types of two-hand-control device shall be used. Moreover, it does not specify the distance between the two-hand control device and the danger zone.
This International Standard provides requirements and guidance on the design and selection (based on a risk assessment) of two-hand control devices including their assessment, the prevention of defeat and the avoidance of faults. It also provides requirements and guidance for two-hand control devices containing a programmable electronic system.
This International Standard applies to all two-hand control devices, independent of the energy used, including:
two-hand control devices which are or are not integral parts of a machine; two-hand control devices which consist of one or more than one separate element.
|
Withdrawn |
2002-03 |
Edition : 1 |
Number of pages : 23 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13851:2019 |
Safety of machinery — Two-hand control devices — Principles for design and selection |
This document specifies the safety requirements of a two-hand control device (THCD) and the dependency of the output signal from the actuation by hand of the control actuating devices.
This document describes the main characteristics of THCDs for the achievement of safety and sets out combinations of functional characteristics for three types. It does not apply to devices intended to be used as enabling devices, as hold-to-run devices or as special control devices.
This document does not specify with which machines THCDs shall be used. It also does not specify which types of two-hand-control device shall be used for a specific application. Moreover, while guidance is given, it does not specify the required distance between the THCD and the danger zone (see 8.8).
This document provides requirements for design and guidance on the selection (based on a risk assessment) of THCDs including the prevention of defeat, the avoidance of faults and verification of compliance.
NOTE 1 A THCD only offers protection for the person using it.
NOTE 2 For specific machines, the suitability of a two-hand control as a suitable protective device can be defined in a type-C standard. If such a standard does not exist or is not appropriate, the risk assessment and determination of suitable protective measures is the responsibility of the manufacturer of the machine.
This document applies to all THCDs, independent of the energy used, including:
— THCDs which are fully assembled for installation;
— THCDs which are assembled by the machine manufacturer or integrator.
This document is not applicable to THCDs manufactured before the date of its publication.
|
Published |
2019-03 |
Edition : 2 |
Number of pages : 21 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13852:1996 |
Safety of machinery — Safety distances to prevent danger zones being reached by the upper limbs |
Gives values for safety distances to prevent danger zones being reached by the upper limbs of persons of 3 years of age and above without additional aid. The distances apply when adequate safety can be achieved by distances alone.
|
Withdrawn |
1996-12 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13853:1998 |
Safety of machinery — Safety distances to prevent danger zones being reached by the lower limbs |
|
Withdrawn |
1998-09 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13854:1996 |
Safety of machinery — Minimum gaps to avoid crushing of parts of the human body |
Purpose is to enable the user (e.g. standard makers, designers of machinery) to avoid hazards from crushing zones. Specifies minimum gaps relative to parts of the human body. Applicable when adequate safety can be achieved by this method.
|
Withdrawn |
1996-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13854:2017 |
Safety of machinery — Minimum gaps to avoid crushing of parts of the human body |
ISO 13854:2017 enables the user (e.g. standard makers, designers of machinery) to avoid hazards from crushing zones. It specifies minimum gaps relative to parts of the human body and is applicable when adequate safety can be achieved by this method.
ISO 13854:2017 is applicable to risks from crushing hazards only and is not applicable to other possible hazards, e.g. impact, shearing, drawing-in.
NOTE For impact, shearing, drawing-in hazards, additional or other measures are to be taken.
|
Published |
2017-11 |
Edition : 2 |
Number of pages : 5 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13855:2002 |
Safety of machinery — Positioning of protective equipment with respect to the approach speeds of parts of the human body |
This International Standard provides parameters based on values for hand/arm and approach speeds and the methodology to determine the minimum distances from sensing or actuating devices of protective equipment to a danger zone.
These specific devices are:
trip devices as defined in EN 292-1:1991, 3.23.5 (specifically electro-sensitive protective equipment, pressure sensitive mats), including those used additionally to initiate operation;two-hand control devices as defined in EN 292-1:1991, 3.23.4 and covered by ISO 13851.
NOTE For the purposes of this International Standard, hold-to-run controls, which are designed to be actuated with one hand, are not considered to be protective equipment.
This International Standard does not apply to protective equipment which is intended to be moved, without tools, nearer to the danger zone than the calculated distance, e.g. pendant two-hand control devices.
The minimum distances derived from this standard do not apply to protective equipment used to detect the presence of persons within an area already protected by a guard or electro-sensitive protective equipment.
|
Withdrawn |
2002-02 |
Edition : 1 |
Number of pages : 19 |
Technical Committee |
13.110
Safety of machinery
|
| ISO/FDIS 14119 |
Safety of machinery — Interlocking devices associated with guards — Principles for design and selection |
|
Under development |
|
Edition : 3 |
|
Technical Committee |
13.110
Safety of machinery
|
| ISO 13855:2010 |
Safety of machinery — Positioning of safeguards with respect to the approach speeds of parts of the human body |
ISO 13855:2010 establishes the positioning of safeguards with respect to the approach speeds of parts of the human body.
It specifies parameters based on values for approach speeds of parts of the human body and provides a methodology to determine the minimum distances to a hazard zone from the detection zone or from actuating devices of safeguards.
The values for approach speeds (walking speed and upper limb movement) in ISO 13855:2010 are time tested and proven in practical experience. ISO 13855:2010 gives guidance for typical approaches. Other types of approach, for example running, jumping or falling, are not considered in ISO 13855:2010.
Safeguards considered in ISO 13855:2010 include:
- electro-sensitive protective equipment, including light curtains and light grids (AOPDs), and laser scanners (AOPDDRs) and two-dimensional vision systems;
- pressure-sensitive protective equipment, especially pressure-sensitive mats;
- two-hand control devices;
- interlocking guards without guard locking.
|
Published |
2010-05 |
Edition : 2 |
Number of pages : 40 |
Technical Committee |
13.110
Safety of machinery
|
| ISO/FDIS 13855 |
Safety of machinery — Positioning of safeguards with respect to the approach of the human body |
|
Under development |
|
Edition : 3 |
|
Technical Committee |
13.110
Safety of machinery
|
| ISO 13856-1:2001 |
Safety of machinery — Pressure-sensitive protective devices — Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors |
|
Withdrawn |
2001-08 |
Edition : 1 |
Number of pages : 42 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13856-1:2013 |
Safety of machinery — Pressure-sensitive protective devices — Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors |
ISO 13856-1:2013 establishes general principles and specifies requirements for the design and testing of pressure-sensitive mats and pressure-sensitive floors normally actuated by the feet for use as devices for protecting persons from hazardous machinery. The minimum safety requirements for the performance, marking and documentation are given.
ISO 13856-1:2013 is applicable to pressure-sensitive mats and pressure-sensitive floors, regardless of the type of energy used (e.g. electrical, hydraulic, pneumatic or mechanical), designed to detect
— persons weighing more than 35 kg, and
— persons (e.g. children) weighing more than 20 kg.
It is not applicable to the detection of persons weighing less than 20 kg.
It does not specify the following because they are application-specific:
a) dimensions or configuration of the effective sensing area of pressure-sensitive mat(s) or pressure-sensitive floor(s) in relation to any particular application;
b) when pressure-sensitive mats or floors are appropriate in a particular situation;
c) performance levels (PLs) for safety-related parts of control systems (SRP/CSs) other than providing a minimum level.
ISO 13856-1:2013 gives guidance to assist the user (i.e. machinery manufacturer and/or user of the machinery) in providing an adequate arrangement.
|
Published |
2013-04 |
Edition : 2 |
Number of pages : 49 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13856-2:2005 |
Safety of machinery — Pressure-sensitive protective devices — Part 2: General principles for the design and testing of pressure-sensitive edges and pressure-sensitive bars |
ISO 13856-2:2005 specifies the general principles and requirements for the design and testing of pressure-sensitive edges and pressure-sensitive bars for use as safety devices and not as actuating devices for normal operation. It is applicable to pressure-sensitive edges and pressure-sensitive bars, with or without an external reset facility, used to detect persons or parts of persons who may be exposed to danger such as hazardous moving parts. Its purpose relates primarily to safety and reliability rather than suitability.
It is restricted to the functioning of pressure-sensitive edges and pressure-sensitive bars and does not specify the requirements for their application, but does contain requirements for the information for use to be provided by the manufacturer. It does not specify the dimensions of the pressure-sensitive edges or bars in relation to a particular application. It is not applicable to stopping devices according to IEC 60204-1 used only for normal operational, including emergency stopping, of machinery. Additional requirements could be necessary where pressure-sensitive edges and pressure-sensitive bars are used in locations accessible to elderly or disabled people or children.
|
Withdrawn |
2005-02 |
Edition : 1 |
Number of pages : 51 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13856-2:2013 |
Safety of machinery — Pressure-sensitive protective devices — Part 2: General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars |
ISO 13856-2:2012 establishes general principles and specifies requirements for the design and testing of pressure-sensitive edges and pressure-sensitive bars used as safeguards and not as actuating devices for normal operation.
ISO 13856-2:2012 is applicable to pressure-sensitive edges and pressure-sensitive bars, with or without an external reset facility, used to detect persons or body parts that can be exposed to hazards such as those caused by the moving parts of machines.
It is not applicable to determining the suitability of a pressure-sensitive edge or pressure-sensitive bar for a particular safeguarding application, selection of an appropriate performance level for safety-related parts of control systems (SRP/CSs) other than to give minimum values,dimensioning or configuring of the effective sensing area of pressure-sensitive edges or pressure-sensitive bars in relation to any particular application or to stopping devices according to IEC 60204-1 used only for normal operation, including emergency stopping of machinery.
|
Published |
2013-04 |
Edition : 2 |
Number of pages : 55 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14120:2002 |
Safety of machinery — Guards — General requirements for the design and construction of fixed and movable guards |
|
Withdrawn |
2002-02 |
Edition : 1 |
Number of pages : 26 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13856-3:2013 |
Safety of machinery — Pressure-sensitive protective devices — Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices |
ISO 13856-3:2013 establishes general principles and specifies requirements for the design and testing of those pressure-sensitive protective devices, with or without an external reset facility, that are not specified in either ISO 13856‑1 or ISO 13856‑2, and the majority of which are produced for specific applications and are not available as "off-the-shelf" items.
ISO 13856-3:2013 also gives specific requirements for the following pressure-sensitive protective devices: pressure-sensitive bumpers; pressure-sensitive plates; pressure-sensitive wires (trip wires).
It deals with the design of a pressure-sensitive device with regard to safety and reliability rather than its suitability for particular applications.
It is not applicable to specifying the dimensions of pressure-sensitive protective devices in relation to any particular application, or stopping devices according to IEC 60204‑1 used for the normal operation, including emergency stopping of machinery.
While requirements are given for the immunity of the device to electromagnetic disturbances, these are not intended to cover all aspects of electromagnetic compatibility (EMC).
|
Published |
2013-07 |
Edition : 2 |
Number of pages : 56 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13857:2008 |
Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs |
ISO 13857:2007 establishes values for safety distances in both industrial and non-industrial environments to prevent machinery hazard zones being reached. The safety distances are appropriate for protective structures. It also gives information about distances to impede free access by the lower limbs. It covers people of 14 years and older (the 5th percentile stature of 14 year olds is approximately 1 400 mm). In addition, for upper limbs only, it provides information for children older than 3 years (5th percentile stature of 3 year olds is approximately 900 mm) where reaching through openings needs to be addressed.
|
Withdrawn |
2008-03 |
Edition : 1 |
Number of pages : 17 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 13857:2019 |
Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs |
This document establishes values for safety distances in both industrial and non-industrial environments to prevent machinery hazard zones being reached. The safety distances are appropriate for protective structures. It also gives information about distances to impede free access by the lower limbs (see Annex B).
This document covers people of 14 years and older (the 5th percentile stature of 14-year-olds is approximately 1 400 mm). In addition, for upper limbs only, it provides information for children older than 3 years (5th percentile stature of 3-year-olds is approximately 900 mm) where reaching through openings needs to be addressed.
NOTE 1 It is not practical to specify safety distances for all persons. Therefore, the values presented are intended to cover the 95th percentile of the population.
Data for preventing lower limb access for children is not considered.
The distances apply when sufficient risk reduction can be achieved by distance alone. Because safety distances depend on size, some people of extreme dimensions will still be able to reach hazard zones even when the requirements of this document are met.
Compliance with the requirements in this document will prevent access to the hazard zone. Nevertheless the user of this document is advised that it does not provide the required risk reduction for every hazard (e.g. hazards related to machine emissions such as ionizing radiation, heat sources, noise, dust).
The clauses covering lower limbs apply on their own only when access by the upper limbs to the same hazard zone is not foreseeable according to the risk assessment.
The safety distances are intended to protect those persons trying to reach hazard zones under the conditions specified (see 4.1.1).
NOTE 2 This document is not intended to provide measures against reaching a hazard zone by climbing over (see ISO 14120:2015, 5.18).
|
Published |
2019-10 |
Edition : 2 |
Number of pages : 20 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14118:2000 |
Safety of machinery — Prevention of unexpected start-up |
|
Withdrawn |
2000-09 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14118:2017 |
Safety of machinery — Prevention of unexpected start-up |
ISO 14118:2017 specifies requirements for designed-in means aimed at preventing unexpected machine start-up (see 3.2) to allow safe human interventions in danger zones (see Annex A).
ISO 14118:2017 applies to unexpected start-up from all types of energy source, i.e.:
- power supply, e.g. electrical, hydraulic, pneumatic;
- stored energy due to, e.g. gravity, compressed springs;
- external influences, e.g. from wind.
ISO 14118:2017 does not specify performance levels or safety integrity levels for safety-related parts of control systems. While available means to prevent unexpected start-up are identified, this document does not specify the means for the prevention of unexpected machine start-up for specific machines.
NOTE A type-C standard can define the required means for the prevention of harm arising from unexpected start-up. Otherwise, the requirements for a specific machine need to be determined by risk assessment outside the scope of this document.
|
Published |
2017-12 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14119:1998 |
Safety of machinery — Interlocking devices associated with guards — Principles for design and selection |
|
Withdrawn |
1998-04 |
Edition : 1 |
Number of pages : 42 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14119:1998/Amd 1:2007 |
Safety of machinery — Interlocking devices associated with guards — Principles for design and selection — Amendment 1: Design to minimize defeat possibilities |
|
Withdrawn |
2007-05 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14119:2013 |
Safety of machinery — Interlocking devices associated with guards — Principles for design and selection |
ISO 14119:2013 specifies principles for the design and selection ? independent of the nature of the energy source ? of interlocking devices associated with guards.It covers the parts of guards which actuate interlocking devices. It does not necessarily provide all the specific requirements for trapped key systems.
ISO 14119:2013 provides measures to minimize defeat of interlocking devices in a reasonably foreseeable manner.
|
Published |
2013-10 |
Edition : 2 |
Number of pages : 68 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14120:2015 |
Safety of machinery — Guards — General requirements for the design and construction of fixed and movable guards |
ISO 14120:2015 specifies general requirements for the design, construction, and selection of guards provided to protect persons from mechanical hazards.
ISO 14120:2015 indicates other hazards that can influence the design and construction of guards.
ISO 14120:2015 applies to guards for machinery which will be manufactured after it is published.
The requirements are applicable if fixed and movable guards are used. This International Standard does not cover interlocking devices. These are covered in ISO 14119.
ISO 14120:2015 does not provide requirements for special systems relating specifically to mobility such as ROPS (rollover protective structures), FOPS (falling-object protective structures), and TOPS (tip over protective structures) or to the ability of machinery to lift loads.
|
Published |
2015-11 |
Edition : 2 |
Number of pages : 35 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14121-1:2007 |
Safety of machinery — Risk assessment — Part 1: Principles |
ISO 14121-1:2007 establishes general principles intended to be used to meet the risk reduction objectives established in ISO 12100-1:2003, Clause 5. These principles of risk assessment bring together knowledge and experience of the design, use, incidents, accidents and harm related to machinery in order to assess the risks posed during the relevant phases of the life cycle of a machine.
ISO 14121-1:2007 provides guidance on the information that will be required to enable risk assessment to be carried out. Procedures are described for identifying hazards and estimating and evaluating risk. It also gives guidance on the making of decisions relating to the safety of machinery and on the type of documentation required to verify the risk assessment carried out.
It is not applicable to risks posed to domestic animals, property or the environment.
|
Withdrawn |
2007-09 |
Edition : 1 |
Number of pages : 28 |
Technical Committee |
13.110
Safety of machinery
|
| ISO/TR 14121-2:2007 |
Safety of machinery — Risk assessment — Part 2: Practical guidance and examples of methods |
ISO/TR 14121-2:2007 gives practical guidance on the conducting of risk assessments for machinery in accordance with ISO 14121-1 and describes various methods and tools for each step in the process.
It also provides practical guidance on risk reduction (in accordance with ISO 12100) for machinery, giving additional guidance on the selection of appropriate protective measures for achieving safety.
The intended users of ISO/TR 14121-2:2007 are those involved in the integration of safety into the design, installation or modification of machinery (e.g. designers, technicians, safety specialists).
|
Withdrawn |
2007-12 |
Edition : 1 |
Number of pages : 71 |
Technical Committee |
13.110
Safety of machinery
|
| ISO/TR 14121-2:2012 |
Safety of machinery — Risk assessment — Part 2: Practical guidance and examples of methods |
ISO/TR 14121-2:2012 gives practical guidance on conducting risk assessment for machinery in accordance with ISO 12100 and describes various methods and tools for each step in the process. It gives examples of different measures that can be used to reduce risk and is intended to be used for risk assessment on a wide variety of machinery in terms of complexity and potential for harm. Its intended users are those involved in the design, installation or modification of machinery (for example, designers, technicians or safety specialists).
|
Published |
2012-06 |
Edition : 2 |
Number of pages : 38 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14121:1999 |
Safety of machinery — Principles of risk assessment |
|
Withdrawn |
1999-02 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14122-1:2001 |
Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means of access between two levels |
|
Withdrawn |
2001-05 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14122-1:2001/Amd 1:2010 |
Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means of access between two levels — Amendment 1 |
|
Withdrawn |
2010-04 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14122-1:2016 |
Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access |
ISO 14122-1:2016 gives general requirements for access to stationary machines and guidance about the correct choice of means of access when necessary access to the stationary machine is not possible directly from the ground level or from a floor.
It is applicable to permanent means of access which are a part of a stationary machine, and also to non-powered adjustable parts (e.g. foldable, slidable) and movable parts of fixed means of access.
NOTE 1 "Fixed" means of access are those mounted in such a manner (for example, by screws, nuts, welding) that they can only be removed by the use of tools.
ISO 14122-1:2016 specifies minimum requirements that also apply when the same means of access is required as the part of the building or civil construction (e.g. working platforms, walkways, ladders) where the machine is installed, on condition that the main function of that part of the construction is to provide a means of access to the machine.
NOTE 2 Where no local regulation or standards exist, this part of ISO 14122 can be used for means of access which are outside the scope of the standard.
It is intended that this part of ISO 14122 be used with a relevant access-specific part of ISO 14122.
The ISO 14122 series as a whole is applicable to both stationary and mobile machinery where fixed means of access are necessary. It is not applicable to powered means of access such as lifts, escalators, or other devices specially designed to lift persons between two levels.
ISO 14122-1:2016 is not applicable to machinery manufactured before the date of its publication.
For the significant hazards covered by this part of ISO 14122, see Clause 4.
|
Published |
2016-06 |
Edition : 2 |
Number of pages : 10 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14122-2:2001 |
Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
|
Withdrawn |
2001-05 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14122-2:2016 |
Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
ISO 14122-2:2016 gives requirements for non-powered working platforms and walkways which are a part of a stationary machine, and to the non-powered adjustable parts (e.g. foldable, sliding) and movable parts of those fixed means of access.
NOTE 1 "Fixed" means of access are those mounted in such a manner (for example, by screws, nuts, welding) that they can only be removed by the use of tools.
ISO 14122-2:2016 specifies minimum requirements that also apply when the same means of access is required as the part of the building or civil construction (e.g. working platforms, walkways) where the machine is installed, on condition that the main function of that part of the construction is to provide a means of access to the machine.
NOTE 2 Where no local regulation or standards exist, this part of ISO 14122 can be used for means of access which are outside the scope of the standard.
It is intended that this part of ISO 14122 be used with ISO 14122‑1 to give the requirements for walking platforms and walkways.
The ISO 14122 series as a whole is applicable to both stationary and mobile machinery where fixed means of access are necessary. It is not applicable to powered means of access such as lifts, escalators, or other devices specially designed to lift persons between two levels.
ISO 14122-2:2016 is not applicable to machinery manufactured before the date of its publication.
|
Published |
2016-06 |
Edition : 2 |
Number of pages : 13 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14122-3:2001 |
Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
|
Withdrawn |
2001-05 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14122-3:2001/Amd 1:2010 |
Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails — Amendment 1 |
|
Withdrawn |
2010-04 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14122-3:2016 |
Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
ISO 14122-3:2016 gives requirements for non-powered stairs, stepladders and guard-rails which are a part of a stationary machine, and to the non-powered adjustable parts (e.g. foldable, slidable) and movable parts of those fixed means of access.
NOTE 1 "Fixed" means of access are those mounted in such a manner (for example, by screws, nuts, welding) that they can only be removed by the use of tools.
ISO 14122-3:2016 specifies minimum requirements that also apply when the same means of access is required as the part of the building or civil construction (e.g. stairs, stepladders, guard-rails) where the machine is installed, on condition that the main function of that part of the construction is to provide a means of access to the machine.
NOTE 2 Where no local regulation or standards exists, this part of ISO 14122 may be used also for means of access which are outside the scope of the standard.
It is intended that this part of ISO 14122 be used with ISO 14122‑1 to give the requirements for steps, stepladders and guard-rails.
The ISO 14122 series as a whole is applicable to both stationary and mobile machinery where fixed means of access are necessary. It is not applicable to powered means of access such as lifts, escalators, or other devices specially designed to lift persons between two levels.
ISO 14122-3:2016 is not applicable to machinery manufactured before the date of its publication.
|
Published |
2016-06 |
Edition : 2 |
Number of pages : 22 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14122-4:2004 |
Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
ISO 14122-4:2004 applies to all machinery (stationary and mobile) where fixed means of access are necessary.
The purpose of the standard is to define the general requirements for safe access to machines mentioned in ISO 12100-2. ISO 14122-1 gives advice about the correct choice of access means when the necessary access to the machine is not possible directly from the ground level or from a floor.
The standard applies to fixed ladders which are a part of a machine.
It may also be applied to ladders fixed to that part of the building where the machine is installed, providing the main function of that part of the building is to provide a means of access to the machine.
It also applies to ladders which are not permanently fixed to the machine and which may be removed, moved to the side or pivoted (swivel-mounted) for some operations of the machine (e.g. changing tools in a large press).
|
Withdrawn |
2004-12 |
Edition : 1 |
Number of pages : 29 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14122-4:2004/Amd 1:2010 |
Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders — Amendment 1 |
|
Withdrawn |
2010-04 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 19085-13:2020 |
Woodworking machines — Safety — Part 13: Multi-blade rip sawing machines with manual loading and/or unloading |
This document gives the safety requirements and measures for stationary multi-blade rip sawing machines manually loaded and/or unloaded, hereinafter referred to as "machines", designed to cut solid wood and material with similar physical characteristics to wood.
It deals with all significant hazards, hazardous situations and events as listed in Clause 4 relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account.
NOTE For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
This document does not deal with specific hazards related to the combination of single machines with any other machine as part of a line.
It is not applicable to machines:
— with all saw blades spindles mounted below the workpiece support/level only;
— intended for use in potentially explosive atmosphere;
— manufactured prior to its publication.
|
Published |
2020-05 |
Edition : 1 |
Number of pages : 40 |
Technical Committee |
13.110
Safety of machinery
;
79.120.10
Woodworking machines
|
| ISO 14122-4:2016 |
Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
ISO 14122-4:2016 gives requirements for fixed ladders which are a part of a stationary machine, and to the non-powered adjustable parts (e.g. foldable, slidable) and movable parts of fixed ladder systems.
NOTE 1 "Fixed" means of access are those mounted in such a manner (for example, by screws, nuts, welding) that they can only be removed by the use of tools.
ISO 14122-4:2016 specifies minimum requirements that also apply when the same means of access is required as the part of the building or civil construction (e.g. fixed ladders) where the machine is installed, on condition that the main function of that part of the construction is to provide a means of access to the machine.
NOTE 2 Where no local regulation or standards exists, this part of ISO 14122 may be used also for means of access which are outside the scope of the standard.
It is intended that this part of ISO 14122 be used with ISO 14122‑1 to give the requirements for fixed ladder systems.
The ISO 14122 series as a whole is applicable to both stationary and mobile machinery where fixed means of access are necessary. It is not applicable to powered means of access such as lifts, escalators, or other devices specially designed to lift persons between two levels.
ISO 14122-4:2016 is not applicable to machinery manufactured before the date of its publication.
|
Published |
2016-06 |
Edition : 2 |
Number of pages : 47 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14123-1:1998 |
Safety of machinery — Reduction of risks to health from hazardous substances emitted by machinery — Part 1: Principles and specifications for machinery manufacturers |
|
Withdrawn |
1998-04 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14123-1:2015 |
Safety of machinery — Reduction of risks to health resulting from hazardous substances emitted by machinery — Part 1: Principles and specifications for machinery manufacturers |
ISO 14123-1:2015 establishes principles for the control of risks to health resulting from hazardous substances emitted by machinery.
ISO 14123-1:2015 is not applicable to substances that are a hazard to health solely because of their explosive, flammable or radioactive properties or their behaviour at extremes of temperature or pressure.
|
Published |
2015-10 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14123-2:1998 |
Safety of machinery — Reduction of risks to health from hazardous substances emitted by machinery — Part 2: Methodology leading to verification procedures |
|
Withdrawn |
1998-04 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14123-2:2015 |
Safety of machinery — Reduction of risks to health resulting from hazardous substances emitted by machinery — Part 2: Methodology leading to verification procedures |
ISO 14123-2:2015 establishes a methodology that leads to the selection of critical factors relating to emissions of hazardous substances for the purpose of specifying suitable verification procedures.
ISO 14123-2:2015 is intended to be used in conjunction with ISO 14123‑1 and relates specifically to ISO 14123‑1:2015, Clause 8.
|
Published |
2015-11 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14159:2002 |
Safety of machinery — Hygiene requirements for the design of machinery |
This International Standard specifies hygiene requirements of machines and provides information for the intended use to be provided by the manufacturer. It applies to all types of machines and associated equipment used in applications where hygiene risks to the consumer of the product can occur.
This International Standard does not cover requirements relative to the uncontrolled egress of microbiological agents from the machine.
|
Published |
2002-04 |
Edition : 1 |
Number of pages : 30 |
Technical Committee |
13.110
Safety of machinery
|
| ISO 14738:2002 |
Safety of machinery — Anthropometric requirements for the design of workstations at machinery |
This International Standard establishes principles for deriving dimensions from anthropometric measurements and applying them to the design of workstations at non-mobile machinery. It is based on current ergonomic knowledge and anthropometric measurements.
This International Standard specifies the body's space requirements for equipment during normal operation in sitting and standing positions. This International Standard does not specifically include space demands for maintenance, repairing and cleaning work.
This International Standard does not give recommendations specifically for visual display terminal workstations at machinery. For this purpose ISO 9241-5 can be used in conjunction with this International Standard.
Situations where people are to be prevented from reaching a hazard are dealt with in ISO 13852.
|
Published |
2002-09 |
Edition : 1 |
Number of pages : 26 |
Technical Committee |
13.110
Safety of machinery
;
13.180
Ergonomics
|
| ISO 14738:2002/Cor 1:2003 |
Safety of machinery — Anthropometric requirements for the design of workstations at machinery — Technical Corrigendum 1 |
|
Published |
2003-12 |
Edition : 1 |
|
Technical Committee |
13.110
Safety of machinery
;
13.180
Ergonomics
|
| ISO 14738:2002/Cor 2:2005 |
Safety of machinery — Anthropometric requirements for the design of workstations at machinery — Technical Corrigendum 2 |
|
Published |
2005-02 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
13.110
Safety of machinery
;
13.180
Ergonomics
|
| ISO 15534-2:2000 |
Ergonomic design for the safety of machinery — Part 2: Principles for determining the dimensions required for access openings |
This part of ISO 15534 specifies the dimensions of openings for access into machinery as defined in
ISO/TR 12100-1. It provides the dimensions to which the values given in ISO 15534-3 are applicable. Values for
additional space requirements are given in annex A. This part of ISO 15534 has been prepared primarily for nonmobile
machinery; there may be additional specific requirements for mobile machinery.
Dimensions for access openings are based on the values for the 95th percentile, whereas reach distances are
based on the values for the 5th percentile, in each case the least favourable body dimension of the expected user
population being used as a basis. The same considerations apply to the location of access openings.
The anthropometric data given in ISO 15534-3 originate from static measurements of nude persons and do not
take into account body movements, clothing, equipment, machinery-operating conditions or environmental
conditions.
This part of ISO 15534 shows how to combine the anthropometric data with suitable allowances to take these
factors into account.
Situations where people are to be prevented from reaching a hazard are dealt with in ISO 13852.
|
Published |
2000-02 |
Edition : 1 |
Number of pages : 23 |
Technical Committee |
13.110
Safety of machinery
;
13.180
Ergonomics
|
| ISO 15534-3:2000 |
Ergonomic design for the safety of machinery — Part 3: Anthropometric data |
This part of ISO 15534 specifies current requirements for human body measurements (anthropometric data) that are
required by ISO 15534-1 and ISO 15534-2 for the calculation of access-opening dimensions as applied to machinery.
The anthropometric data originate from static measurements of nude persons and do not take into account body
movements, clothing, equipment, machinery-operating conditions or environmental conditions.
The data are based on information from anthropometric surveys representative of population groups within Europe
comprising at least three million people. Both men and women are taken into account.
Measurements are given, as required by ISO 15534-1 and ISO 15534-2, for the 5th, 95th and 99th percentiles of the
relevant population group within Europe.
|
Published |
2000-02 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
13.110
Safety of machinery
;
13.180
Ergonomics
|
| ISO 15537:2004 |
Principles for selecting and using test persons for testing anthropometric aspects of industrial products and designs |
ISO 15537:2004 establishes methods for determining the composition of groups of persons whose anthropometric characteristics are to be representative of the intended user population of any specific object under test.
ISO 15537:2004 is applicable to the testing of anthropometric aspects of industrial products and designs having direct contact with the human body or dependent on human body measurements, e.g. machinery, work equipment, personal protective equipment (PPE), consumer goods, working spaces, architectural details or transportation equipment.
ISO 15537:2004 is also applicable to the testing of such safety aspects of products that are dependent on human body measurements. It does not deal with other aspects of the task or other requirements, such as perception of information (except geometrical arrangement of the viewing targets) and the use of controls (except their geometrical placement).
|
Withdrawn |
2004-11 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
13.110
Safety of machinery
;
13.180
Ergonomics
|
| ISO 15537:2022 |
Principles for selecting and using test persons for testing anthropometric aspects of industrial products and designs |
This document establishes methods for determining the composition of groups of persons whose anthropometric characteristics are to be representative of the intended user population of any specific object under test.
This document is applicable to the testing of anthropometric aspects of industrial products and designs having direct contact with the human body or dependent on human body measurements, such as machinery, work equipment, personal protective equipment (PPE), consumer goods, working spaces, architectural details or transportation equipment.
This document is also applicable to the testing of such safety aspects of products that are dependent on human body measurements. It does not deal with other aspects of the task or other requirements, such as perception of information (except geometrical arrangement of the viewing targets) and the use of controls (except their geometrical placement).
Although this document deals with selecting test persons from an anthropometric perspective, similar general principles can be applied for other test variables, e.g. biomechanical aspects.
|
Published |
2022-05 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
13.110
Safety of machinery
;
13.180
Ergonomics
|
| ISO 19085-2:2017 |
Woodworking machines — Safety — Part 2: Horizontal beam panel circular sawing machines |
ISO 19085-2:2017 gives the safety requirements and measures for horizontal beam panel circular sawing machines with the saw carriage of the front cutting line mounted below the work-piece support, which are manually and/or powered loaded and manually unloaded, hereinafter referred to as "machines".
ISO 19085-2:2017 deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
NOTE For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
ISO 19085-2:2017 is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
- side pressure device;
- device for powered unloading;
- unit for scoring;
- unit for post-formed/soft-formed edge pre-cutting;
- panel turning device;
- front side turn table;
- pushing out device;
- pneumatic clamping of the saw blade;
- powered panel loading device;
- device for grooving by milling tool;
- one or more additional cutting lines inside the machine for longitudinal and/or head cut (before the transversal cutting line);
- work-piece vacuum clamping as part of a front side turn table or of a panel loading device.
The machines are designed for cutting panels consisting of
a) solid wood,
b) material with similar physical characteristics to wood (see ISO 19085‑1:2017, 3.2),
c) gypsum boards, gypsum bounded fibreboards,
d) composite boards made from the materials listed above, and
e) composite materials with core consisting of e.g. polyurethane or mineral material laminated with light alloy.
ISO 19085-2:2017 does not deal with hazards related to
- specific features that differ from the dashed list above,
- the machining of panels with milling tools for grooving,
- powered unloading of panels,
- rear half of split pressure beam on the front cutting line,
- the combination of a single machine being used with any other machine (as part of a line).
ISO 19085-2:2017 is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.
|
Withdrawn |
2017-07 |
Edition : 1 |
Number of pages : 35 |
Technical Committee |
13.110
Safety of machinery
;
79.120.10
Woodworking machines
|
| ISO 16090-1:2022 |
Machine tools safety — Machining centres, milling machines, transfer machines — Part 1: Safety requirements |
This document specifies the technical safety requirements and protective measures for the design, construction and supply (including installation and dismantling, with arrangements for transport and maintenance) of:
— milling machines (see 3.1.1), including machines capable of performing boring operations (see 3.1.2);
— machining centres; and
— transfer machines (see 3.1.3)
designed for continuous production use, which are intended to cut cold metal and other non-combustible cold materials, except wood or materials with physical characteristics similar to those of wood as defined in ISO 19085‑1 and glass, stone and engineered/agglomerated materials as defined in EN 14618.
This document covers the following machines (referred to as "machines" in this document):
a) manually, without numerical control, operated boring and milling machines (see 3.2.1, Group 1), e.g. knee and column type milling machines (see Figures C.1 and C.2);
b) manually, with limited numerical control, operated boring and milling machines (see 3.2.2, Group 2), e.g. profile and contouring milling machines (see Figures C.3 and C.4);
c) numerically controlled milling machines and machining centres (see 3.2.3, Group 3), e.g. automatic milling machines and milling centres, e.g. multi-spindle milling machines, gear-milling machines (see Figures C.5 to C.7);
d) transfer and special-purpose machines (see 3.2.4, Group 4), which are designed to process only pre-specified workpieces or limited range of similar workpieces by means of a predetermined sequence of machining operations and process parameters (see Figures C.8 to C.13).
e) machines fitted with the following devices/facilities, whose hazards have been dealt with:
— tool magazine(s);
— tool changer(s);
— workpiece handling mechanism(s);
— powered workpiece clamping mechanism(s);
— swarf/chip conveyor(s);
— power-operated door(s);
— moveable operator cabin(s);
— additional equipment for turning;
— additional equipment for grinding.
This document deals with all significant hazards, hazardous situations and events relevant to this type of machinery which can occur during transportation, assembly and installation, setting, operation, cleaning and maintenance, troubleshooting, dismantling or disabling according to ISO 12100, when the machinery is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This document presumes accessibility to the machine from all directions and specifies access conditions to operator positions. It also applies to workpiece transfer devices including transport devices for loading/unloading when they form an integral part of the machine.
|
Published |
2022-11 |
Edition : 2 |
Number of pages : 155 |
Technical Committee |
13.110
Safety of machinery
;
25.080.01
Machine tools in general
|
| ISO/TR 18569:2004 |
Safety of machinery — Guidelines for the understanding and use of safety of machinery standards |
ISO/TR 18569:2004 provides assistance to the designer or manufacturer of machinery and related equipment on the contents and how to apply the relevant Type A and Type B safety of machinery standards.
It provides an overview which gives a general outline of the basic steps which can assist the manufacturer to declare conformity with the EU Machinery Directive and related standards or apply supporting standards in the case when specific Type C standards do not exist. It provides an outline of the various standards associated with machinery safety.
|
Withdrawn |
2004-05 |
Edition : 1 |
Number of pages : 78 |
Technical Committee |
01.120
Standardization. General rules
;
13.110
Safety of machinery
|
| ISO 19085-1:2017 |
Woodworking machines — Safety — Part 1: Common requirements |
ISO 19085-1:2017 gives the safety requirements and measures to reduce risks related to woodworking machines arising during operation, adjustment, maintenance, transport, assembly, dismantling, disabling and scrapping and which are common to machines used in the woodworking industry. It is applicable to woodworking, stationary and displaceable machines when they are used as intended and under the conditions foreseen by the manufacturer.
NOTE 1 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
ISO 19085-1:2017 is intended to be used in conjunction with the other parts of ISO 19085, applicable to specific machine types.
ISO 19085-1:2017 is not applicable to machines intended for use in potential explosive atmospheres or to machines manufactured prior to the date of its publication.
NOTE 2 Machines for capturing and extracting dust are covered by EN 12779 and EN 16770.
|
Withdrawn |
2017-07 |
Edition : 1 |
Number of pages : 47 |
Technical Committee |
13.110
Safety of machinery
;
79.120.10
Woodworking machines
|
| ISO 19085-1:2021 |
Woodworking machines — Safety — Part 1: Common requirements |
This document gives the safety requirements and measures to reduce risks arising during operation, adjustment, maintenance, transport, assembly, dismantling, disabling and scrapping, related to woodworking machines capable of continuous production use, hereinafter referred as "machines". These safety requirements and measures are those common to most of the machines, when they are used as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too.
The machines are designed to process solid wood and material with similar physical characteristics to wood, with hand feed or integrated feed.
This document is intended to be used in conjunction with the other parts of the ISO 19085 series, applicable to specific machine types. The extent to which all significant hazards of a specific machine type are covered is indicated in the specific part of the ISO 19085 series relevant to that machine type. The hazards covered, at least partly, by the requirements of this document, are listed in Annex A.
It is not applicable to machines intended for use in potential explosive atmospheres or to machines manufactured prior to the date of its publication.
|
Published |
2021-03 |
Edition : 2 |
Number of pages : 47 |
Technical Committee |
13.110
Safety of machinery
;
79.120.10
Woodworking machines
|
| ISO 19085-2:2021 |
Woodworking machines — Safety — Part 2: Horizontal beam panel circular sawing machines |
This document gives the safety requirements and measures for horizontal beam panel circular sawing machines with the saw carriage of the front cutting line mounted below the workpiece support, which are manually and/or powered loaded and manually unloaded, capable of continuous production use, as defined in 3.1 and hereinafter referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
— side pressure device;
— device for powered unloading;
— unit for scoring;
— unit for post-formed/soft-formed edge pre-cutting;
— panel turning device;
— front side turn table;
— pushing out device;
— pneumatic clamping of the saw blade;
— powered panel loading device;
— device for grooving by milling tool;
— one or more additional cutting lines inside the machine for longitudinal and/or head cut (before the transversal cutting line);
— workpiece vacuum clamping as part of a front side turn table or of a panel loading device;
— panel pusher;
— independent panel pushers;
— additional panel pushers mounted on the panel pusher carriage;
— additional panel pusher with integrated label printer device;
— lifting platform;
— device for automatic loading of thin panels;
— device for base board unloading by gravity;
— device for base board powered unloading;
— device for panel unloading in limited space condition;
— loading or pre-loading roller conveyors;
— pressure beam with additional flaps to increase dust extraction efficiency;
— saw blade cooling system by air or water-air or oil-air;
— vibrating conveyor with/without trimming unit for offcuts management;
— predisposition for top loading/unloading by an external system directly on the machine table and/or on the machine preloading roller conveyor and/or on the machine lifting table.
NOTE base board is a support panel underlying the panel stack, to protect the panels from damages during transportation.
The machines are designed for cutting panels consisting of:
a) solid wood;
b) material with similar physical characteristics to wood (see ISO19085‑1:2021, 2);
c) gypsum boards, gypsum bounded fibreboards;
d) composite materials, with core consisting of e.g. polyurethane or mineral material, laminated with light alloy;
e) cardboard;
f) foam board;
g) matrix engineered mineral boards, silicate boards;
h) polymer‐matrix composite materials and reinforced thermoplastic/thermoset/elastomeric materials;
i) aluminium light alloy plates with a maximum thickness of 10 mm;
j) composite boards made from the materials listed above.
This document does not deal with hazards related to:
— specific features different from those listed above;
— the machining of panels with milling tools for grooving;
— powered unloading of panels;
— rear half of split pressure beam on the front cutting line;
— the combination of a single machine being used with any other machine (as part of a line).
It is not applicable to:
— machines intended for use in potentially explosive atmospheres;
— machines manufactured prior to the date of its publication.
|
Published |
2021-10 |
Edition : 2 |
Number of pages : 43 |
Technical Committee |
13.110
Safety of machinery
;
79.120.10
Woodworking machines
|