| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO 3129:2019 |
Wood — Sampling methods and general requirements for physical and mechanical testing of small clear wood specimens |
This document specifies methods for the extensive and limited sampling of wood, conditioning and preparation of test pieces. It also specifies the general requirements for physical and mechanical testing of small clear wood specimens. The sampling guidance provided in this document can be applied for timber taken from either trees, logs, or pieces of ungraded/graded/presorted sawn timber for non-structural applications, such as furniture, windows, doors, etc., only.
|
Published |
2019-11 |
Edition : 3 |
Number of pages : 8 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3130:1975 |
Wood — Determination of moisture content for physical and mechanical tests |
Specifies a method that determines, by weighing, the loss in mass of the test piece on drying to constant mass. Calculation of the loss in mass as a percentage of test piece mass after drying. Reference is made to ISO 3129.
|
Withdrawn |
1975-11 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3131:1975 |
Wood — Determination of density for physical and mechanical tests |
The method described determines the moisture content at the time of test and in the absolutely dry condition as well as the mass ratio in the absolutely dry condition to volume of the test piece with moisture content greater than or equal to the fibre saturation point.
|
Withdrawn |
1975-11 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3132:1975 |
Wood — Testing in compression perpendicular to grain |
Determination of the proportional limit (conventional ultimate strength), the load being applied to the whole surface (radial or tangential) of the test piece. References are made to ISO 3129 and ISO 3130.
|
Withdrawn |
1975-11 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3133:1975 |
Wood — Determination of ultimate strength in static bending |
Describes apparatus, preparation of test pieces as well as procedure and calculation and expression of results in detail. References are made to ISO 3129 and ISO 3130.
|
Withdrawn |
1975-11 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3179:1974 |
Coniferous sawn timber — Nominal dimensions |
Represents the combinatin of ISO/DIS 3179, 3181, and 3182 in a single document. Applies to unplaned square-edged and unedged shaped sawn timber 16 to 300 mm thick of different widths and differend shaped edges. The nominal thicknesses and widths are given in a table.
|
Withdrawn |
1974-11 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3345:1975 |
Wood — Determination of ultimate tensile stress parallel to grain |
The principle consists in the application of a gradually increasing load to a test piece. Apparatus, preparation of test piece, procedure and calculation and expression of results are described in detail. References are made to ISO 3129 and ISO 3130.
|
Withdrawn |
1975-09 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3346:1975 |
Wood — Determination of ultimate tensile stress perpendicular to grain |
Covers the radial and tangential directions. The principle consists in the application of a gradually increasing load to a test piece. Apparatus, preparation of test piece, procedure and calculation and expression of results are described in detail. References are made to ISO 3129 and ISO 3130.
|
Withdrawn |
1975-12 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3347:1976 |
Wood — Determination of ultimate shearing stress parallel to grain |
The method described is based on applying a gradually increasing compressive load, either along the radial or along the tangential surface of a test piece. References are made to ISO 3129 and ISO 3130.
|
Withdrawn |
1976-01 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3348:1975 |
Wood — Determination of impact bending strength |
Specifies a method using a pendulum impact testing machine. The test piece is tested for cross-sectional bending under dynamic load application. References are made to ISO 3129 and ISO 3130.
|
Withdrawn |
1975-08 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3349:1975 |
Wood — Determination of modulus of elasticity in static bending |
Method described measures the deflection in the net bending area during application of a gradually increasing load to a test piece within the region of proportionality of the load and deflection.
|
Withdrawn |
1975-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3350:1975 |
Wood — Determination of static hardness |
Specifies a method that determines the resistance of a test piece to the penetration of a plunger to a specified depth under a gradually increasing load. References are made to ISO 3129 and ISO 3130.
|
Withdrawn |
1975-08 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3351:1975 |
Wood — Determination of resistance to impact indentation |
The method described determines the resistance of the surface layer of a test piece to impact indentation by a steel ball being dropped from a height of 500 1 mm. With a pressing mechanism the test piece is held against a massive base-plate.
|
Withdrawn |
1975-12 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 3787:1976 |
Wood — Test methods — Determination of ultimate stress in compression parallel to grain |
|
Withdrawn |
1976-09 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 4469:1981 |
Wood — Determination of radial and tangential shrinkage |
Specifies a method which determines the linear dimensions of test pieces after drying at a moisture content in equilibrium with the normal environment and at a moisture content equal to or greater than the saturation point of the cellular wall of wood.
|
Withdrawn |
1981-11 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 4470:1981 |
Sawn timber — Determination of the average moisture content of a lot |
Two methods are specified: a) Measuring the electrical resistance or conductance of the test pieces using an electrical moisture meter and b) determining the loss in mass after drying test pieces until absolutely dry.
|
Published |
1981-12 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 4471:1982 |
Wood — Sampling sample trees and logs for determination of physical and mechanical properties of wood in homogeneous stands |
The method of selecting the appropriate test areas is described. Annexes A to E provide forms for the following: A = Description of the test area and taxation characteristics; B = Overall inventory report on trees growing in the test area No....; C = Inventory report on trees of species to be examined in test area No....; D = Inventory report on selection of sample trees in test area; E = Card of sample tree No....
|
Published |
1982-05 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 4472:1983 |
Coniferous and broadleaved sawn timber — Transportation packages |
Specifies requirements for square-edged and unedged, planed and unplaned sawn timber. Appropriate definitions are given and illustrated in the figure. Dimensions and mass are listed in a table.
|
Published |
1983-05 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 4473:1988 |
Coniferous and broadleaved tree sawlogs — Visible defects — Classification |
Refers to the terms and definitions given in ISO 4474. The following six groups are listed in a table in connection with their subgroups and varieties: Knots, shakes, defects of trunk shape, defects of wood structure, defects caused by fungi and damage.
|
Withdrawn |
1988-08 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 4474:1989 |
Coniferous and broadleaved tree sawlogs — Visible defects — Terms and definitions |
Refers to ISO 4473 and is a trilingual edition. Examples are illustrated in six figures. Includes an alphabetical index in English, French and Russian.
|
Withdrawn |
1989-09 |
Edition : 1 |
Number of pages : 15 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
;
01.040.79
Wood technology (Vocabularies)
|
| ISO 4475:1989 |
Coniferous and broadleaved tree sawlogs — Visible defects — Measurement |
Refers to the classification in ISO 4473 and to terms and definitions given in ISO 4474. Examples are illustrated in 13 figures. Where linear measurement is specified, this always refers to whole centimetres rounded off to the nearest centimetre below.
|
Published |
1989-07 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 4476:1983 |
Coniferous and broadleaved sawlogs — Sizes — Vocabulary |
The terms and definitions include the different types of ends, of diameters and other dimensions. This standard is a trilingual edition.
|
Withdrawn |
1983-04 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
;
01.040.79
Wood technology (Vocabularies)
|
| ISO 4480:1983 |
Coniferous sawlogs — Measurement of sizes and determination of volume |
The vocabulary given in ISO 4476 applies to the methods specified. The thickness shall be taken as the middle diameter or the diameter of the upper end. The length shall be measured in metres, rounded to two decimal places. The volume shall be determined in cubic metres to two decimal places.
|
Withdrawn |
1983-08 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 4858:1982 |
Wood — Determination of volumetric shrinkage |
Two methods are specified: the stereometric method used for test pieces made in accordance with ISO 4469, and the mercury volumenometer method used for test pieces of any shape. References are made to ISO 3129, ISO 3130, and ISO 4469.
|
Withdrawn |
1982-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 4859:1982 |
Wood — Determination of radial and tangential swelling |
Specifies a method which determines the linear swelling of test pieces after drying at a moisture content in equilibrium with the normal environment and at a moisture content, equal to or greater than the saturation point of the cellular walls of wood.
|
Withdrawn |
1982-12 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 4860:1982 |
Wood — Determination of volumetric swelling |
Two methods are specified: the stereometric method used for test pieces made in accordance with ISO 4859, and the mercury volumenometer method used for test pieces of any shape. Determines the change in volume of test pieces after drying, at a moisture content in equilibrium with the normal environment and at a moisture content, equal to or greater than the saturation point of the cellular walls of wood.
|
Withdrawn |
1982-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 8903:1994 |
Broadleaved sawn timber — Nominal sizes |
Specifies nominal sizes of unplaned, square-edged and unedged, broadleaved sawn timber.
|
Withdrawn |
1994-10 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 8903:2016 |
Broadleaved sawn timber — Nominal sizes |
ISO 8903:2016 specifies nominal sizes of unplanned, square-edged and unedged, sawn timber.
|
Published |
2016-02 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 8904:1990 |
Broadleaved sawn timber — Sizes — Methods of measurement |
Specifies the methods of measurement of the length, width, thickness and volume of sawn timber. Applies to unplaned, square-edged and unedged sawn timber
|
Published |
1990-11 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 8905:1988 |
Sawn timber — Test methods — Determination of ultimate strength in shearing parallel to grain |
This International Standard specifies a method of testing sawn timber of coniferous and broadleaved species in shearing parallel to the grain to determine the ultimate strength.
|
Published |
1988-07 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 8906:1988 |
Sawn timber — Test methods — Determination of resistance to local transverse compression |
This method is based on the load proportional limit and the load at a defined deformation which are given in the "load/deflection" curve. Stresses at these loads are calculated. Testing of small defect-free test pieces of wood is not covered.
|
Published |
1988-07 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 9086-1:1987 |
Wood — Methods of physical and mechanical testing — Vocabulary — Part 1: General concepts and macrostructure |
Gives terms and definitions relating to physical and mechanical properties of wood. Wood is defined as aggregate of secondary tissues (conductive, mechanical and storing) found in stems, branches and roots of woody plants between the bark and pith.
|
Withdrawn |
1987-11 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
;
01.040.79
Wood technology (Vocabularies)
|
| ISO 9709:2005 |
Structural timber — Visual strength grading — Basic principles |
ISO 9709:2005 establishes the basic principles for rules and procedures governing the visual sorting of timber for use in structural applications.
|
Withdrawn |
2005-07 |
Edition : 1 |
Number of pages : 25 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 9709:2018 |
Structural timber — Visual strength grading — Basic principles |
This document establishes the basic principles for rules and procedures governing the visual sorting of timber for use in structural applications.
|
Published |
2018-10 |
Edition : 2 |
Number of pages : 39 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13059:2011 |
Round timber — Requirements for the measurement of dimensions and methods for the determination of volume |
ISO 13059:2011 establishes requirements for the measurement of dimensions and methods for the determination of round timber volume.
|
Published |
2011-09 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-1:2014 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 1: Determination of moisture content for physical and mechanical tests |
ISO 13061-1:2014 specifies oven-drying methods for determining the moisture content of wood for physical and mechanical tests on small clear wood specimens.
|
Published |
2014-10 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-1:2014/Amd 1:2017 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 1: Determination of moisture content for physical and mechanical tests — Amendment 1 |
|
Published |
2017-06 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-2:2014 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 2: Determination of density for physical and mechanical tests |
ISO 13061-2:2014 specifies a method for determining the density of wood for physical and mechanical tests on small clear wood specimens. It may also be used to determine density of test specimens for other physical or mechanical test and/or to determine the relationship between density and other properties of wood.
|
Published |
2014-10 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-2:2014/Amd 1:2017 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 2: Determination of density for physical and mechanical tests — Amendment 1 |
|
Published |
2017-06 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-3:2014 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 3: Determination of ultimate strength in static bending |
ISO 13061-3:2014 specifies a method for determining the ultimate strength of wood in static bending by measuring the breaking load applied in the mid-span of a simply supported beam.
|
Published |
2014-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 779:2001 |
Paper, board and pulp — Determination of iron |
|
Withdrawn |
2001-06 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
85.040
Pulps
|
| ISO 13061-4:2014 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 4: Determination of modulus of elasticity in static bending |
ISO 13061-4:2014 specifies a method for determining the modulus of elasticity of wood in static bending by measuring the deflection in the mid-span of a simply supported beam.
|
Published |
2014-12 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-4:2014/Amd 1:2017 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 4: Determination of modulus of elasticity in static bending — Amendment 1 |
|
Published |
2017-06 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-5:2020 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 5: Determination of strength in compression perpendicular to grain |
This document specifies a method for determining the strength in compression perpendicular to grain of wood.
|
Published |
2020-01 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-6:2014 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 6: Determination of ultimate tensile stress parallel to grain |
ISO 13061-6:2014 specifies a method for determining the ultimate tensile stress of wood parallel to grain on small clear specimens by measuring the breaking load applied statically along the longitudinal axis of a test piece.
|
Published |
2014-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-7:2014 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 7: Determination of ultimate tensile stress perpendicular to grain |
ISO 13061-7:2014 specifies a method for the determination of ultimate tensile stress of wood perpendicular to grain of small clear specimens in the radial and tangential directions by measuring the breaking load applied statically perpendicular to the longitudinal axis of a test piece.
|
Published |
2014-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-8:2022 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 8: Determination of ultimate strength in shearing parallel to grain |
This document specifies a method for determining the ultimate strength in shearing parallel to grain of small clear wood specimens by measuring the breaking load applied statically along the radial or the tangential plane of a test piece.
|
Published |
2022-06 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-10:2017 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 10: Determination of impact bending strength |
ISO 13061-10:2017 specifies a method for determining the impact bending strength of wood.
|
Published |
2017-10 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-11:2017 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 11: Determination of resistance to impact indentation |
ISO 13061-11:2017 specifies a method for the determination of the resistance of wood to impact indentation by a steel ball.
|
Published |
2017-10 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-12:2017 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 12: Determination of static hardness |
ISO 13061-12:2017 specifies a method for determining of the static hardness of wood by measuring resistance of a test piece to the penetration of a plunger under gradually increasing load.
|
Published |
2017-10 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-13:2016 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 13: Determination of radial and tangential shrinkage |
ISO 13061-13:2016 specifies a method for the determination of linear shrinkage in the radial and tangential directions of wood.
|
Published |
2016-11 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO/DIS 13061-13 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 13: Determination of radial and tangential shrinkage |
ISO 13061-13:2016 specifies a method for the determination of linear shrinkage in the radial and tangential directions of wood.
|
Under development |
|
Edition : 2 |
Number of pages : 3 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-14:2016 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 14: Determination of volumetric shrinkage |
ISO 13061-14:2016 specifies methods for the determination of volumetric shrinkage of wood.
|
Published |
2016-11 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO/DIS 13061-14 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 14: Determination of volumetric shrinkage |
ISO 13061-14:2016 specifies methods for the determination of volumetric shrinkage of wood.
|
Under development |
|
Edition : 2 |
Number of pages : 5 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-15:2017 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 15: Determination of radial and tangential swelling |
ISO 13061-15:2017 specifies a method for the determination of linear swelling in the radial and tangential directions of wood.
|
Published |
2017-06 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-16:2017 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 16: Determination of volumetric swelling |
ISO 13061-16:2017 specifies methods for the determination of volumetric swelling of wood.
|
Published |
2017-06 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-17:2017 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 17: Determination of ultimate stress in compression parallel to grain |
ISO 13061-17:2017 specifies a method for determining the ultimate stress in compression parallel to grain of wood.
|
Published |
2017-10 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13061-18:2022 |
Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 18: Vocabulary |
This document lists the terms and definitions relating to general concepts, macrostructure, sampling, and methods of physical and mechanical testing of wood. Other terminologies that are not mentioned in this standard are defined in ISO 24294.
|
Published |
2022-01 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13912:2005 |
Structural timber — Machine strength grading — Basic principles |
ISO 13912:2005 establishes the basic principles for rules and procedures governing the machine sorting of timber for use in structural applications.
|
Withdrawn |
2005-07 |
Edition : 1 |
Number of pages : 22 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 13912:2017 |
Structural timber — Machine strength grading — Basic principles |
ISO 13912:2017 establishes the basic principles for rules and procedures governing the machine sorting of timber for use in structural applications. This applies to conventional bending type strength-grading machines as well as more recent machines that use other properties for strength-grading purposes.
|
Published |
2017-11 |
Edition : 2 |
Number of pages : 26 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 16415:2012 |
Non-structural timber grading requirements |
ISO 16415:2012 delineates and illustrates broad grade categories that specify essential features typically found in those categories based on commonalities of numerous national standards and grading rules used for non-structural timber of non-coniferous and coniferous species in international commerce.
ISO 16415:2012 provides a basis for recognition of a national standard or grading rules that complies with ISO 16415:2012 and is applicable to all methods of visual grading systems for non-structural timber of all non-coniferous and coniferous species of timber.
Non-structural timber produced from bamboo is not covered by ISO 16415:2012.
|
Published |
2012-08 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 17959:2014 |
General requirements for solid wood flooring |
ISO 17959:2014 specifies the requirements and test methods of characteristics of solid wood flooring boards for internal (interior) use as flooring. It also specifies packaging and marking requirements.
It is applicable to both finished and unfinished solid wood flooring board. Solid wood parquet is not covered.
|
Published |
2014-12 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 19474:2018 |
Round timber — Visual characteristics — Methods of determination |
ISO 19474:2018 defines requirements to methods of determination of visual characteristics of round timber.
|
Published |
2018-03 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 21625:2020 |
Vocabulary related to bamboo and bamboo products |
This document defines terms related to bamboo, intermediate bamboo and bamboo products.
This document is applicable to bamboo, intermediate bamboo and bamboo products in production and trade.
|
Published |
2020-07 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
;
01.040.79
Wood technology (Vocabularies)
|
| ISO 2067:2019 |
Granulated cork, broken cork and crushed cork — Sampling for the determination of moisture content |
This document specifies a sampling method for the determination of moisture content of granulated cork, broken cork and crushed cork.
|
Published |
2019-10 |
Edition : 4 |
Number of pages : 2 |
Technical Committee |
79.100
Cork and cork products
|
| ISO 21887:2007 |
Durability of wood and wood-based products — Use classes |
ISO 21887:2007 defines five use classes that represent different service situations to which wood and wood-based products can be exposed all over the world. Subclasses are also defined for these use classes.
ISO 21887:2007 applies only to preservatives and processes for pre-treatment of wood and wood products and is not intended for products and processes for remediation and eradication of existing damage to timber. The annex to ISO 21887:2007 provides guidance on applying use classification to specify preservative treatments, treated wood, naturally durable and modified wood but does not provide definitive specifications.
|
Published |
2007-11 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
;
71.100.50
Wood-protecting chemicals
;
79.060.01
Wood-based panels in general
|
| ISO 22157-1:2004 |
Bamboo — Determination of physical and mechanical properties — Part 1: Requirements |
ISO 22157-1:2004 specifies test methods for evaluating the following characteristic physical and strength properties for bamboo: moisture content, mass per volume, shrinkage, compression, bending, shear and tension.
|
Withdrawn |
2004-06 |
Edition : 1 |
Number of pages : 19 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO/TR 22157-2:2004 |
Bamboo — Determination of physical and mechanical properties — Part 2: Laboratory manual |
ISO/TR 22157-2:2004 provides informative guidelines for staff in laboratories on how to perform tests according to ISO 22157-1:2004.
|
Withdrawn |
2004-05 |
Edition : 1 |
Number of pages : 21 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 22157:2019 |
Bamboo structures — Determination of physical and mechanical properties of bamboo culms — Test methods |
This document specifies test procedures for specimens obtained from round bamboo culms. The data obtained from the test methods can be used to establish characteristic physical or mechanical properties to be used in structural engineering design or for other scientific purposes. This document provides methods for evaluating the following physical and strength properties: moisture content, density, mass per unit length; strength properties parallel to the fibre direction, compression, tension and bending, and strength properties perpendicular to the fibre direction, tension and bending. It also provides methods to estimate moduli of elasticity in bending, compression and tension parallel to fibres, and bending perpendicular to fibres.
The test methods reported in this document are intended for commercial testing applications. The test methods reported in this document are intended for commercial testing applications and can also be adopted as benchmark methods for scientific research.
This document is organized to provide requirements for standard tests to be carried out to determine the material properties of full-culm bamboo as a structural material.
|
Published |
2019-01 |
Edition : 1 |
Number of pages : 25 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 23066:2021 |
Vocabulary related to rattan materials and products |
This document defines terms relating to rattan source plants, materials, intermediate rattan products and rattan products.
This document is applicable to rattan materials and products in production and trade.
|
Published |
2021-02 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
;
01.040.79
Wood technology (Vocabularies)
|
| ISO 23067:2022 |
Grading system for rattan: Requirements and classification |
This document gives guidelines and requirements to sort and classify rattan cane materials (poles and derivatives) based on physical properties, quality and market values.
|
Published |
2022-07 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
|
| ISO 24294:2013 |
Timber — Round and sawn timber — Vocabulary |
ISO 24294:2013 contains the terms and definitions of concepts to establish a multilingual vocabulary of terminology to be applied in forest and wood working spheres, with the scope of identification of a tree and of its parts in round and sawn aspects; its measurements; grading; condition; features; sizes; and the natural, biological and infestational defects of wood.
|
Withdrawn |
2013-09 |
Edition : 1 |
Number of pages : 70 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
;
01.040.79
Wood technology (Vocabularies)
|
| ISO 24294:2021 |
Timber — Round and sawn timber — Vocabulary |
This document defines terms related to round and sawn timber. It applies to identification of a tree and its components, stages of processing in round and sawn forms, and timber grading, dimensions, anatomical structure, features, moisture content and conditions relating to stain, fungal and insect attack. It does not apply to terms related to strength properties of wood, engineered timber products or timber structures.
|
Published |
2021-09 |
Edition : 2 |
Number of pages : 46 |
Technical Committee |
79.040
Wood, sawlogs and sawn timber
;
01.040.79
Wood technology (Vocabularies)
|
| ISO 631:1975 |
Mosaic parquet panels — General characteristics |
These panels of any species of wood are assemblies made from wood fingers of a parallelepiped rectangular shape, forming component squares laid in a chequered pattern; they are intended to be bonded (or sealed) to a supporting base, either directly or over an interlayer of adequate material. Specified are dimensions, permissible deviations, etc., the inspection and delivery conditions and marking.
|
Published |
1975-11 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 1072:1975 |
Solid wood parquet — General characteristics |
Specified are cross-section, dimensions, permissible deviations, etc., the inspection and delivery conditions and the marking of strips with rectangular face of any species of wood. They are manufactured in three different profiles, calles respectively: types P1 (variants A and B), P2 and P3, the dimension characteristics of which are given in tables and shown in figures.
|
Published |
1975-09 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 1324:1985 |
Solid wood parquet — Classification of oak strips |
Divides non-assembled strips into three quality grades that are identified by (+++), (++), (+) corresponding to the conditions specified in the tables. Designation or names for these quality grades may be assigned in national standards, provided that such standard indicate, at least in a note, the relationship with the ISO classification. Replaces Recommendation ISO/R 1324-1970 of which it constitutes a technical revision.
|
Published |
1985-06 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO/R 1324:1970 |
Classification of parquet strips of solid oak |
|
Withdrawn |
1970-06 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 2036:1976 |
Wood for manufacture of wood flooring — Symbols for marking according to species |
These symbols are composed of four adjoining capital letters, not separated by points and not followed by a full stop. The letter X as the fourth indicates that any species of the respective genus is concerned. When characteristic differences presented by different species of one genus are to be taken into account, the fourth letter is the first of the species name. The Annex contains the code of symbols.
|
Published |
1976-03 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 2457:1976 |
Solid wood parquet — Classification of beech strips |
Divides non-assembled strips into two quality grades that are identified by (+++) and (++) corresponding to the conditions specified in the tables. The regulations for manufacture, characteristics and delivery conditions are fixed by ISO 1072. Replaces the first edition from 1972.
|
Published |
1976-06 |
Edition : 2 |
Number of pages : 3 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 3397:1977 |
Broadleaved wood raw parquet blocks — General characteristics |
Lays down manufacturing characteristics and dimensions, permissible deviations, methods for quality control and delivery conditions, measurement and marking assisted by tables and examples.
|
Published |
1977-02 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 3398:1977 |
Broadleaved wood raw parquet blocks — Classification of oak parquet blocks |
Divides the blocks used for manufacturing different types of parquets by quality into the three grades I, II, and M corresponding to the conditions stated in the tables. Grade M is mainly intended for manufacturing mosaic parquet. The regulations for manufacture, characteristics and delivery conditions are fixed by ISO 3397.
|
Published |
1977-02 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 3399:1976 |
Broadleaved wood raw parquet blocks — Classification of beech parquet blocks |
Divides the blocks by quality into the two grades I and II corresponding to the conditions stated in the tables. Unless otherwise requested, the wood shall be steamed before delivery and the type of sawing may be the subject of special agreements in the orders. The regulations for manufacture, characteristics and delivery conditions are fixed by ISO 3397.
|
Published |
1976-04 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 3810:1977 |
Cork — Floor tiles of agglomerated cork — Methods of test |
|
Withdrawn |
1977-02 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.080
Semi-manufactures of timber
;
79.100
Cork and cork products
|
| ISO 3810:1987 |
Floor tiles of agglomerated cork — Methods of test |
The following characteristics are determined: dimensions and squareness, apparent density, tensile strength, initial and residual indentation, ash content and resistance to boiling hydrochloric acid. Replaces the first edition of which this constitutes a technical revision.
|
Published |
1987-10 |
Edition : 2 |
Number of pages : 3 |
Technical Committee |
79.080
Semi-manufactures of timber
;
79.100
Cork and cork products
|
| ISO 3813:1977 |
Cork — Floor tiles of agglomerated cork — Characteristics, sampling and packing |
|
Withdrawn |
1977-03 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
79.080
Semi-manufactures of timber
;
79.100
Cork and cork products
|
| ISO 5334:1978 |
Solid wood parquet — Classification of maritime pine strips |
Divides the non-assembled strips by quality into the three grade (+++), (++), and (+) corresponding to the conditions stated in the tables. The regulations for manufacture, characteristics and delivery conditions are fixed by ISO 1027.
|
Published |
1978-02 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 3813:1987 |
Floor tiles of agglomerated cork — Characteristics, sampling and packing |
This standard applies to tiles without surface covering. Gives the maximum permissible deviations in characteristics measured and determined in accordance with ISO 3810. Clauses 4 and 5 of the first edition have been technically revised.
|
Withdrawn |
1987-05 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
79.080
Semi-manufactures of timber
;
79.100
Cork and cork products
|
| ISO/FDIS 4556 |
Wood raw parquet elements — General characteristics |
|
Under development |
|
Edition : 1 |
Number of pages : 7 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO/FDIS 4561 |
Wood raw elements — Classification |
|
Under development |
|
Edition : 1 |
Number of pages : 7 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO/FDIS 4562 |
Wood parquet strips — Classification |
|
Under development |
|
Edition : 1 |
Number of pages : 8 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 5320:1980 |
Solid wood parquet — Classification of fir and spruce strips |
Divides the blocks by quality into the three grades (+++), (++), and (+) corresponding to the conditions stated in the tables. Refers to a protection treatment to the parts of the strips liable to be attacked by insects. The regulations for manufacture, characteristics and delivery conditions are fixed by ISO 1027.
|
Published |
1980-05 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 5321:1978 |
Coniferous wood raw parquet blocks — General characteristics |
Applies to blocks intended for the manufacture of strips for different types of parquet flooring. Specified are materials, design and manufacture, dimensions, squareness of ends, and permissible deviations, moisture, the methods of sampling and quality control, and delivery conditions, measurement and marking.
|
Published |
1978-02 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 5323:1984 |
Solid wood parquet and raw parquet blocks — Vocabulary |
Establishes terms and definitions for the purpose of expressing as correctly as possible concepts. These terms and definitions are not restrictive. Included are alphabetical indices in the three ISO languages.
|
Withdrawn |
1984-12 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
79.080
Semi-manufactures of timber
;
01.040.79
Wood technology (Vocabularies)
|
| ISO 5323:2019 |
Wood flooring and parquet — Vocabulary |
This document establishes terms and definitions for expressing as correctly as possible concepts relating to wood flooring, parquet and raw parquet blocks.
This document aims to clarify terms and definition of wood floorings and parquet and avoid any confusion with other types of floorings.
|
Published |
2019-07 |
Edition : 2 |
Number of pages : 10 |
Technical Committee |
79.080
Semi-manufactures of timber
;
01.040.79
Wood technology (Vocabularies)
|
| ISO 5326:1978 |
Solid wood paving blocks — Hardwood paving blocks — Quality requirements |
Applies to paving used for covered (indoor) and open (outdoor) spaces. Blocks made of Fagus sylvatica wood are intended for use in covered spaces only. The permissible wood or sawing defects are listed in a table.
|
Published |
1978-02 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 5327:1978 |
Solid wood paving blocks — General characteristics |
Specifies manufacture, dimensions, tolerances and the inspection and delivery conditions and marking. The common and special shapes are shown in figures. Applies to blocks used for paving covered (indoor) and open (outdoor) spaces. Describes the methods of protection treatment.
|
Published |
1978-02 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 5328:1978 |
Solid wood paving blocks — Softwood paving blocks — Quality requirements |
Applies to paving used for covered (indoor) and open (outdoor) spaces. The permissible wood or sawing defects and corresponding acceptance conditions are listed in a table.
|
Published |
1978-02 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 5329:1978 |
Solid wood paving blocks — Vocabulary |
Establishes terms and definitions and shows related figures. The terms and definitions are not restrictive. Included are alphabetical indices in the three ISO languages.
|
Published |
1978-05 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
79.080
Semi-manufactures of timber
;
01.040.79
Wood technology (Vocabularies)
|
| ISO 5333:1978 |
Coniferous wood raw parquet blocks — Classification of fir and spruce parquet blocks |
Divides the blocks by quality into the two grades I and II corresponding to the conditions stated in the tables. The regulations for manufacture, characteristics and delivery conditions are fixed by ISO 5321.
|
Published |
1978-05 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
79.080
Semi-manufactures of timber
|
| ISO 24337:2006 |
Laminate floor coverings — Determination of geometrical characteristics |
ISO 24337:2006 gives test methods to determine the dimensional variance between elements of laminate floor coverings in a manufactured free-standing shape (unrestricted) in respect to thickness, length, width, squareness, straightness, width flatness, length flatness, openings between assembled elements and height differences between assembled elements.
|
Withdrawn |
2006-08 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
79.080
Semi-manufactures of timber
;
97.150
Floor coverings
|