| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO 1420:2001 |
Rubber- or plastics-coated fabrics — Determination of resistance to penetration by water |
|
Withdrawn |
2001-07 |
Edition : 3 |
Number of pages : 3 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 1420:2016 |
Rubber- or plastics-coated fabrics — Determination of resistance to penetration by water |
ISO 1420:2016 specifies two methods for the determination of the resistance of rubber- or plastics-coated fabrics to water penetration (hydrostatic resistance) when subjected to a specific hydrostatic pressure over a fixed period of time. Method A specifies the procedure for a low and high hydrostatic pressure and Method B for a low hydrostatic pressure.
|
Published |
2016-07 |
Edition : 4 |
Number of pages : 6 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 1421:1977 |
Fabrics coated with rubber or plastics — Determination of breaking strength and elongation at break |
|
Withdrawn |
1977-05 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 1421:1998 |
Rubber- or plastics-coated fabrics — Determination of tensile strength and elongation at break |
|
Withdrawn |
1998-06 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 1421:2016 |
Rubber- or plastics-coated fabrics — Determination of tensile strength and elongation at break |
ISO 1421:2016 specifies two methods for the determination of the tensile strength of fabrics coated with rubber or plastics.
- Method 1 ? the strip test method, which is a method for the determination of tensile strength and elongation at break.
- Method 2 ? the grab test method, which is a method for the determination of tensile strength only.
The methods apply to test pieces in equilibrium with specific standard atmospheres for testing and to wet test pieces. Both methods require the use of a constant rate of extension (CRE) tensile-testing machine.
|
Published |
2016-12 |
Edition : 3 |
Number of pages : 13 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2231:1973 |
Fabric coated with rubber or plastics — Standard atmospheres for conditioning and testing |
|
Withdrawn |
1973-11 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2231:1989 |
Rubber- or plastics-coated fabrics — Standard atmospheres for conditioning and testing |
Specifies the requirements and definitions and determines pre-conditioning, characteristics of test atmospheres and methods of conditioning. Technical revision of the clauses 3 and 4 of the first edition (ISO 2231-1973).
|
Published |
1989-08 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2286-1:1998 |
Rubber- or plastics-coated fabrics — Determination of roll characteristics — Part 1: Methods for determination of length, width and net mass |
|
Withdrawn |
1998-06 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 22653:2003 |
Footwear — Test methods for lining and insocks — Static friction |
ISO 22653:2003 specifies two methods of assessing the frictional properties of lining and insocks, irrespective of the material.
|
Published |
2003-12 |
Edition : 1 |
Number of pages : 17 |
Technical Committee |
61.060
Footwear
|
| ISO 2286-1:2016 |
Rubber- or plastics-coated fabrics — Determination of roll characteristics — Part 1: Methods for determination of length, width and net mass |
ISO 2286-1:2016 specifies methods of determining the length, width and net mass of a roll of rubber- or plastics-coated fabrics.
|
Published |
2016-09 |
Edition : 2 |
Number of pages : 3 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2286-2:1998 |
Rubber- or plastics-coated fabrics — Determination of roll characteristics — Part 2: Methods for determination of total mass per unit area, mass per unit area of coating and mass per unit area of substrate |
|
Withdrawn |
1998-06 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2286-2:2016 |
Rubber- or plastics-coated fabrics — Determination of roll characteristics — Part 2: Methods for determination of total mass per unit area, mass per unit area of coating and mass per unit area of substrate |
ISO 2286-2:2016 specifies methods of determining the total mass per unit area, the mass per unit area of the coating and the mass per unit area of the substrate cloth of a rubber- or plastics-coated fabric. Methods for removing coatings of specific compositions are described in Annex A.
|
Published |
2016-09 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2286-3:1998 |
Rubber- or plastics-coated fabrics — Determination of roll characteristics — Part 3: Method for determination of thickness |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2286-3:2016 |
Rubber- or plastics-coated fabrics — Determination of roll characteristics — Part 3: Method for determination of thickness |
ISO 2286-3:2016 specifies a method for the determination, at a specified pressure, of the thickness of rubber- and plastics-coated fabrics, irrespective of the type of substrate employed. It is applicable to single-face, double-face and double-texture coated fabrics, as well as materials in which an expanded layer is included in the coating.
|
Published |
2016-09 |
Edition : 2 |
Number of pages : 3 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2286:1972 |
Fabrics coated with rubber or plastics — Determination of roll characteristics |
|
Withdrawn |
1972-10 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2286:1986 |
Rubber- or plastics-coated fabrics — Determination of roll characteristics |
|
Withdrawn |
1986-11 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2411:1973 |
Rubber- or plastics-coated fabrics — Determination of coating adhesion |
|
Withdrawn |
1973-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2411:1991 |
Rubber- or plastics-coated fabrics — Determination of coating adhesion |
|
Withdrawn |
1991-10 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2411:2000 |
Rubber- or plastics-coated fabrics — Determination of coating adhesion |
|
Withdrawn |
2000-06 |
Edition : 3 |
Number of pages : 11 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2411:2017 |
Rubber- or plastics-coated fabrics — Determination of coating adhesion |
ISO 2411:2017 specifies a method of determining the coating adhesion strength of coated fabrics.
|
Published |
2017-09 |
Edition : 4 |
Number of pages : 11 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO/DIS 2411 |
Rubber- or plastics-coated fabrics — Determination of coating adhesion |
ISO 2411:2017 specifies a method of determining the coating adhesion strength of coated fabrics.
|
Under development |
|
Edition : 5 |
Number of pages : 12 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 3011:1981 |
Rubber or plastics coated fabrics — Determination of resistance to ozone cracking under static conditions |
|
Withdrawn |
1981-12 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 3011:1997 |
Rubber- or plastics-coated fabrics — Determination of resistance to ozone cracking under static conditions |
|
Withdrawn |
1997-04 |
Edition : 3 |
Number of pages : 4 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 4646:2022 |
Rubber- or plastics-coated fabrics — Low-temperature impact test |
This document specifies a procedure for determining the lowest temperature at which rubber- or plastics-coated fabrics will not exhibit fractures or coating cracks when subjected to specific impact conditions.
Rubber-or plastics-coated fabrics are used in many applications involving low-temperature flexing with or without impact. Data obtained by this method can be used to predict the behaviour of these coated fabrics at low temperatures only in the applications in which the conditions of deformation are similar to those specified in the method.
|
Published |
2022-08 |
Edition : 3 |
Number of pages : 9 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 3011:2021 |
Rubber- or plastics-coated fabrics — Determination of resistance to ozone cracking under static conditions |
This document specifies a method for the determination of the resistance of fabrics coated with rubber or plastics to ozone cracking under static conditions.
The test is designed to determine the relative resistance to cracking of fabric coated with rubber or plastics when exposed under static strain to air containing ozone in the absence of direct sunlight.
Like all ageing tests, it should be considered as a means of comparing articles of the same composition and destined for the same application, but not as an absolute criterion. It is preferable to limit the significance of the test by considering it only as a means of control when a fabric attains a resistance superior to a threshold given in comparison with a certain type of degradation.
Taking these remarks into account, the results obtained at the time of test cannot be taken as a prediction of the length of life of the product.
|
Published |
2021-07 |
Edition : 4 |
Number of pages : 4 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 3303-1:2012 |
Rubber- or plastics-coated fabrics — Determination of bursting strength — Part 1: Steel-ball method |
ISO 3303-1:2012 specifies a method for the determination of the bursting strength of rubber- or plastics-coated fabrics, using a mechanically operated steel ball.
|
Withdrawn |
2012-08 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 3303-1:2020 |
Rubber- or plastics-coated fabrics — Determination of bursting strength — Part 1: Steel-ball method |
This document specifies a method for the determination of the bursting strength of rubber or plastics coated fabrics, using a mechanically operated steel ball.
|
Published |
2020-09 |
Edition : 2 |
Number of pages : 5 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 3303-2:2012 |
Rubber- or plastics-coated fabrics — Determination of bursting strength — Part 2: Hydraulic method |
ISO 3303-2:2012 specifies a method for the determination of the bursting strength of rubber- or plastics-coated fabrics, using one of two types of diaphragm bursting tester, designated type A and B, both operated by hydraulic pressure. The type A test machine is applicable to materials having bursting strengths ranging from 350 kPa to 5 500 kPa and the type B test machine is applicable to materials of bursting strengths ranging from 70 kPa to 1 400 kPa.
|
Withdrawn |
2012-08 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 3303-2:2020 |
Rubber- or plastics-coated fabrics — Determination of bursting strength — Part 2: Hydraulic method |
This document specifies a method for the determination of the bursting strength of rubber - or plastics - coated fabrics, using one of two types of diaphragm bursting tester, designated type A and B, both operated by hydraulic pressure.
The type A test machine is applicable to materials having bursting strengths ranging from 350 kPa to 5 500 kPa and the type B test machine is applicable to materials of bursting strengths ranging from 70 kPa to 1 400 kPa.
|
Published |
2020-08 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 3303:1979 |
Rubber- or plastics-coated fabrics — Determination of bursting strength |
|
Withdrawn |
1979-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 3303:1990 |
Rubber- or plastics-coated fabrics — Determination of bursting strength |
Lays down two methods: one using a testing tensile machine with a ring clamp and steel ball and the other using a diaphragm bursting tester operated by hydraulic pressure. The apparatus for the two methods are shown in figures.
|
Withdrawn |
1990-03 |
Edition : 2 |
Number of pages : 3 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 4637:1979 |
Rubber-coated fabrics — Determination of rubber-to-fabric adhesion — Direct tension method |
Only suitable when the material to be tested is substantially uniform in thickness and flat or sufficiently flexible to remain flat in case of slight compression. Particularly suitable for materials having a very thin rubber layer which are difficult to test by stripping or peeling methods. However, it should be noted that the results obtained by this method will not necessarily correlate with those obtained by a stripping test. A figure shows the prepartion of test assembly.
|
Published |
1979-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 4646:1978 |
Rubber or plastics coated fabrics — Low temperature impact test |
|
Withdrawn |
1978-07 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 4646:1989 |
Rubber- or plastics-coated fabrics — Low-temperature impact test |
Determines the lowest temperature at which the fabrics mentioned will not exhibit fractures or coating cracks when subjected to specific impact conditions. An annex deals with the speed calibration of a solenoid-actuated low temperature impact tester.
|
Withdrawn |
1989-07 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 4674-1:2003 |
Rubber- or plastics-coated fabrics — Determination of tear resistance — Part 1: Constant rate of tear methods |
ISO 4674-1:2003 describes two methods for determining the forces necessary to initiate and propagate tearing of a coated fabric using the constant rate of tear method. The methods described are:
method A: tongue tear;method B: trouser tear.
|
Withdrawn |
2003-09 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 4674-1:2016 |
Rubber- or plastics-coated fabrics — Determination of tear resistance — Part 1: Constant rate of tear methods |
ISO 4674-1:2016 specifies two methods for determining the forces necessary to initiate and propagate tearing of a coated fabric using the constant rate of tear method. The methods described are the following:
- method A: tongue tear;
- method B: trouser tear.
|
Published |
2016-10 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 4674-2:1998 |
Rubber- or plastics-coated fabrics — Determination of tear resistance — Part 2: Ballistic pendulum method |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 4674-2:2021 |
Rubber- or plastics-coated fabrics — Determination of tear resistance — Part 2: Ballistic pendulum method |
This document specifies a method for the determination of tear resistance based on the action of an active force applied to a notched test piece.
The test can be carried out on:
test pieces that have been conditioned in a standard atmosphere; or
test pieces that have undergone pre-treatment, e.g. water immersion.
The results obtained by this method cannot be compared with those obtained by methods involving constant rate of tear.
|
Published |
2021-10 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 4674:1977 |
Fabrics coated with rubber or plastics — Determination of tear resistance |
Specifies three methods which are applicable to the fabrics in which the constituents of the backing fabrics perpendicular to the direction of tearing are broken; they are not applicable to fabrics with cellular backing or a meshed cloth backing in which the tear pattern is complex. Methods A1, A2, and B do not give the same results. The test pieces are described by 3 figures.
|
Withdrawn |
1977-08 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 4675:1979 |
Fabrics coated with rubber or plastics — Low temperature bend test |
|
Withdrawn |
1979-05 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 4675:1990 |
Rubber- or plastics-coated fabrics — Low-temperature bend test |
Describes a method for the materials given determining the ability to resist the low-temperature effect to bending at special temperatures after definite periods of exposure. Applicable to material which a thickness between 0.10 and 2.20 mm. Since these materials are used in different applications, no general relationship between this test and the service performance can be given or implied. Two figures show the test apparatus.
|
Withdrawn |
1990-06 |
Edition : 2 |
Number of pages : 5 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 4675:2017 |
Rubber- or plastics-coated fabrics — Low-temperature bend test |
ISO 4675:2017 specifies a method for determining the ability of fabrics coated with rubber or plastics to resist the effect of low temperature when subjected to bending at specified temperatures after definite periods of exposure. This method is applicable to material with a thickness within the range 0,1 mm to 2,2 mm. For materials of greater thickness than this, modifications to the standard equipment apply (see 9.2, third paragraph).
Because fabrics coated with rubber or plastics are used in different applications requiring low temperature flexing, no general relationship between this test and service performance can be given or implied.
|
Published |
2017-08 |
Edition : 3 |
Number of pages : 5 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO/DIS 5462 |
Rubber latex coated fabric gloves — Specification |
|
Under development |
|
Edition : 1 |
Number of pages : 11 |
Technical Committee |
59.080.40
Coated fabrics
;
83.140.99
Other rubber and plastics products
|
| ISO 5470-1:1999 |
Rubber- or plastics-coated fabrics — Determination of abrasion resistance — Part 1: Taber abrader |
|
Withdrawn |
1999-06 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 5470-1:2016 |
Rubber- or plastics-coated fabrics — Determination of abrasion resistance — Part 1: Taber abrader |
ISO 5470-1:2016 describes a method of assessing the abrasive wear resistance of coated fabrics using the Taber abrader.
|
Published |
2016-11 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 5470-2:2003 |
Rubber- or plastics-coated fabrics — Determination of abrasion resistance — Part 2: Martindale abrader |
ISO 5470-2:2003 details two separate methods for determining the resistance of a material to wet and dry abrasion. It is applicable to the coated surface or surfaces of coated fabrics.
|
Withdrawn |
2003-04 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 5470-2:2021 |
Rubber- or plastics-coated fabrics — Determination of abrasion resistance — Part 2: Martindale abrader |
This document specifies two separate methods for determining the resistance of a material to wet and dry abrasion.
It is applicable to the coated surface or surfaces of coated fabrics.
It does not apply to determining the abrasion behaviour of an uncoated surface of a coated fabric, for which the methods for uncoated textiles described in the ISO 12947 series apply.
|
Published |
2021-08 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 5470:1980 |
Rubber or plastics coated fabrics — Determination of abrasion resistance |
Data obtained by this method may be used to predict the behaviour of these fabrics, but not as an absolute criterion. It is preferable to limit the significance of the test by considering it as a means of control only. The method only refers to the abrasion resistance of coating and is useful when comparing materials with the same or similar characteristics. The abrasion is measured by loss in mass. The figure shows a typical abrader.
|
Withdrawn |
1980-05 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 5473:1979 |
Rubber- or plastics-coated fabrics — Determination of crush resistance |
|
Withdrawn |
1979-08 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 5473:1997 |
Rubber- or plastics-coated fabrics — Determination of crush resistance |
The method is applicable particularly to diaphragm material cut from coated fabrics. The coated fabric is subjected to a controlled load application over a known area. Dimensions of the test piece and load assembly are shown in two figures.
|
Published |
1997-02 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 5978:1979 |
Rubber or plastics coated fabrics — Determination of blocking resistance |
|
Withdrawn |
1979-09 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 5978:1990 |
Rubber- or plastics-coated fabrics — Determination of blocking resistance |
The method specified is acceptable in most cases. If it is desired to use conditions other than those specified, these may be mutually agreed between the contracting parties, but such variations shall be stated in the test report. - Constitutes a minor revision of the first edition.
|
Published |
1990-02 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO/FDIS 5978 |
Rubber- or plastics-coated fabrics — Determination of blocking resistance |
|
Under development |
|
Edition : 3 |
|
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 5979:1982 |
Rubber or plastics coated fabrics — Determination of flexibility — Flat loop method |
Specifies a method of characterizing the flexiblity. Not applicable to coated fabrics which are prone to rolling up or spiralling when they are cut into pieces of small dimensions, nor applicable when the coated fabric is too rigid to make a loop. The method can be carried out on the coated fabric as delivered and on a coated fabric which has undergone certain specified treatments. A figure shows the apparatus.
|
Published |
1982-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 5981:1982 |
Rubber or plastics coated fabrics — Determination of flex abrasion |
|
Withdrawn |
1982-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 5981:1997 |
Rubber- or plastics-coated fabrics — Determination of resistance to combined shear flexing and rubbing |
|
Withdrawn |
1997-06 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 5981:2007 |
Rubber- or plastics-coated fabrics — Determination of resistance to combined shear flexing and rubbing |
ISO 5981:2007 specifies two methods of evaluating the resistance to combined shear flexing and rubbing of rubber- or plastics-coated fabrics. Rubbing is either forced by application of a pressure foot (method A), or is caused by simple contact between the faces of the test pieces (method B).
Method B (without application of the pressure foot) is preferred in all cases where the foot would damage the test piece through an abrasive effect where this is not required, e.g. materials with sticky surfaces, light coatings such as polyurethanes on rough surfaces.
The test may be carried out on products as delivered or after pre-treatments such as wetting or accelerated ageing.
NOTE The results obtained using method A and method B cannot be compared as there is no correlation between the two methods.
|
Published |
2007-10 |
Edition : 3 |
Number of pages : 8 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 6179:1981 |
Fabrics coated with vulcanized rubber — Determination of vapour transmission rate of volatile liquids (Gravimetric technique) |
|
Withdrawn |
1981-03 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 6179:1989 |
Vulcanized rubber sheet, and fabrics coated with vulcanized rubber — Determination of transmission rate of volatile liquids (Gravimetric technique) |
|
Withdrawn |
1989-12 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
59.080.40
Coated fabrics
;
83.140.10
Films and sheets
|
| ISO 6179:1998 |
Rubber, vulcanized or thermoplastic — Rubber sheets and rubber-coated fabrics — Determination of transmission rate of volatile liquids (gravimetric technique) |
|
Withdrawn |
1998-04 |
Edition : 3 |
Number of pages : 6 |
Technical Committee |
59.080.40
Coated fabrics
;
83.140.10
Films and sheets
|
| ISO 6179:2010 |
Rubber, vulcanized or thermoplastic — Rubber sheets and rubber-coated fabrics — Determination of transmission rate of volatile liquids (gravimetric technique) |
ISO 6179:2010 specifies two methods for determining, by measurement of the transmission rate, the permeability of rubber to volatile liquids diffusing into open air.
It is applicable only to materials in sheet form and to coated fabrics having thicknesses between 0,2 mm and 3,0 mm.
It is restricted to transmission rates of more than 0,1 g/m2/h.
The methods are particularly useful for comparing the relative transmission rates of one liquid through different materials, or of several liquids through one material.
Method A, with refilling, is used when testing mixtures of liquids which give different transmission rates.
Method B, with no refilling, is used for a single-component liquid.
A method for the determination of water vapour transmission rate is given in ISO 2528, Sheet materials — Determination of water vapour transmission rate — Gravimetric (dish) method.
|
Withdrawn |
2010-03 |
Edition : 4 |
Number of pages : 6 |
Technical Committee |
59.080.40
Coated fabrics
;
83.140.10
Films and sheets
|
| ISO 6179:2017 |
Rubber, vulcanized or thermoplastic — Rubber sheets and rubber-coated fabrics — Determination of transmission rate of volatile liquids (gravimetric technique) |
ISO 6179:2017 specifies two methods for determining, by measurement of the transmission rate, the permeability of rubber to volatile liquids diffusing into open air.
It is applicable only to materials in sheet form and to coated fabrics having thicknesses between 0,2 mm and 3,0 mm.
It is restricted to transmission rates of more than 0,1 g/m2·h.
The methods are particularly useful for comparing the relative transmission rates of one liquid through different materials, or of several liquids through one material.
Method A, with refilling, is used when testing mixtures of liquids which give different transmission rates.
Method B, with no refilling, is used for a single-component liquid.
NOTE A method for the determination of water vapour transmission rate is given in ISO 2528.
|
Published |
2017-07 |
Edition : 5 |
Number of pages : 9 |
Technical Committee |
59.080.40
Coated fabrics
;
83.140.10
Films and sheets
|
| ISO 6450:2005 |
Rubber- or plastics-coated fabrics — Determination of resistance to liquids |
ISO 6450:2005 specifies two methods (methods 1 and 2) of evaluating the resistance of fabrics coated with plastics or with vulcanized rubber to the action of liquids by measurement of selected properties of the materials before and after immersion in selected liquids.
The difference between the two methods is as follows:
In method 1, excess liquid is removed from the test pieces, after immersion, by wiping.In method 2, the test pieces are immersed in a volatile liquid and excess liquid is subsequently removed by drying in an oven.
|
Withdrawn |
2005-09 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 6450:2021 |
Rubber- or plastics-coated fabrics — Determination of resistance to liquids |
This document specifies two methods of evaluating the resistance of rubber- or plastics-coated fabrics to the action of liquids by measurement of selected properties of the materials before and after immersion in selected liquids.
The two methods are as follows:
— Method A: total immersion with liquid;
— Method B: one surface side immersion with liquid.
|
Published |
2021-09 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 6451:1982 |
Plastics coated fabrics — Polyvinyl chloride coatings — Rapid method for checking fusion |
Specifies a method for checking the coatings on coated fabrics. Not suitable for coatings obtained from aqueous dispersions of PVC.
|
Published |
1982-09 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 6452:2000 |
Rubber- or plastics-coated fabrics — Determination of fogging characteristics of trim materials in the interior of automobiles |
|
Withdrawn |
2000-07 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
43.040.60
Bodies and body components
;
59.080.40
Coated fabrics
|
| ISO 6452:2007 |
Rubber- or plastics-coated fabrics — Determination of fogging characteristics of trim materials in the interior of automobiles |
ISO 6452:2007 specifies a test method which is intended to determine the fogging characteristics of rubber- or plastics-coated fabrics that are used as trim materials in the interior of motor vehicles.
The method may also be applicable to fluid, pasty, powdered or solid raw materials which are the basis for such trim materials or from which the materials are manufactured. The method may also be applicable to other materials and finished products.
|
Withdrawn |
2007-06 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
43.040.60
Bodies and body components
;
59.080.40
Coated fabrics
|
| ISO 7617-2:2003 |
Plastics-coated fabrics for upholstery — Part 2: Specification for PVC-coated woven fabrics |
ISO 7617-2:2003 specifies requirements for coated fabrics for upholstered furniture, manufactured by applying to one side of a woven cloth a substantially continuous coating of a suitably plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride. Such coatings are known as poly(vinyl chloride) (PVC) coatings. The present specification covers two grades (A and B) of PVC-coated woven fabric.
|
Published |
2003-08 |
Edition : 3 |
Number of pages : 8 |
Technical Committee |
97.140
Furniture
;
59.080.40
Coated fabrics
|
| ISO 6452:2021 |
Rubber- or plastics-coated fabrics — Determination of fogging characteristics of trim materials in the interior of automobiles |
This document specifies a test method which is intended to determine the fogging characteristics of rubber- or plastics-coated fabrics that are used as trim materials in the interior of motor vehicles.
The method can also apply to fluid, pasty, powdered or solid raw materials which are the basis for such trim materials or from which the materials are manufactured. The method can also apply to other materials and finished products.
The procedure is applicable to the measurement of fog condensate on glass surfaces within the limits of the test conditions. This test cannot measure accurately those cases in which:
— the surface tension of the condensate is low, resulting in early coalescing into a thin transparent film;
— the condensate is present in such a large quantity that the droplets coalesce and form a heavy oily/clear film (this heavy film gives false readings).
In such cases, the gravimetric method is preferred.
|
Published |
2021-05 |
Edition : 3 |
Number of pages : 16 |
Technical Committee |
43.040.60
Bodies and body components
;
59.080.40
Coated fabrics
|
| ISO 7229:1997 |
Rubber- or plastics-coated fabrics — Measurement of gas permeability |
Describes a method of measuring gas transmission through fabrics coated with plastics or rubber. Applicable when the anticipated permeability is less than 3 cubic decimetres, when particular temperature or pressure conditions are required or when the measurement requires the use of particular gases, either in pure state or as a mixture.
|
Withdrawn |
1997-01 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 7229:2015 |
Rubber- or plastics-coated fabrics — Measurement of gas permeability |
ISO 7229:2015 specifies two methods for measuring gas transmission through rubber- or plastics-coated fabrics, a property known as permeability.
|
Withdrawn |
2015-09 |
Edition : 2 |
Number of pages : 16 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 7229:2022 |
Rubber- or plastics-coated fabrics — Measurement of gas permeability |
This document specifies two methods for measuring gas transmission through rubber- or plastics-coated fabrics, a property known as permeability.
|
Published |
2022-08 |
Edition : 3 |
Number of pages : 16 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 7617-1:1994 |
Plastics-coated fabrics for upholstery — Part 1: Specification for PVC-coated knitted fabrics |
Cancels and replaces the first edition (1988). Specifies requirements for coated fabrics for upholstered furniture, manufactured by applying to one side of a single jersey weft-knitted base cloth a substantially continuous coating of a suitably plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride.
|
Withdrawn |
1994-10 |
Edition : 2 |
Number of pages : 13 |
Technical Committee |
97.140
Furniture
;
59.080.40
Coated fabrics
|
| ISO 7617-1:2001 |
Plastics-coated fabrics for upholstery — Part 1: Specification for PVC-coated knitted fabrics |
This part of ISO 7617 specifies technical requirements for coated fabrics for upholstered furniture for interior use,
obtained by applying to one side of a weft-knitted base cloth a substantially continuous coating of a suitably
plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride. Such coatings
are known as poly(vinyl chloride) (PVC) coatings. The present specification covers fabrics coated with solid PVC
and also covers two grades with coatings consisting of a layer of expanded PVC.
|
Published |
2001-12 |
Edition : 3 |
Number of pages : 17 |
Technical Committee |
97.140
Furniture
;
59.080.40
Coated fabrics
|
| ISO/DIS 7617-1 |
Plastics-coated fabrics for upholstery — Part 1: Specification for PVC-coated knitted fabrics |
This part of ISO 7617 specifies technical requirements for coated fabrics for upholstered furniture for interior use,
obtained by applying to one side of a weft-knitted base cloth a substantially continuous coating of a suitably
plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride. Such coatings
are known as poly(vinyl chloride) (PVC) coatings. The present specification covers fabrics coated with solid PVC
and also covers two grades with coatings consisting of a layer of expanded PVC.
|
Under development |
|
Edition : 4 |
|
Technical Committee |
83.140
Rubber and plastics products
;
97.140
Furniture
;
59.080.40
Coated fabrics
|
| ISO 7617-2:1994 |
Plastics-coated fabrics for upholstery — Part 2: Specification for PVC-coated woven fabrics |
Cancels and replaces the first edition (1988). Specifies requirements for coated fabrics for upholstered furniture, manufactured by applying to one side of a woven cloth a substantially continuous coating of a suitably plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride.
|
Withdrawn |
1994-10 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
97.140
Furniture
;
59.080.40
Coated fabrics
|
| ISO 9407:2019 |
Footwear sizing — Mondopoint system of sizing and marking |
This document specifies a method of designation and marking of footwear size called Mondopoint, based on defined measurements of the foot that the footwear is intended to fit.
This document is applicable to all types of footwear.
|
Published |
2019-06 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
61.060
Footwear
|
| ISO 7617-3:1988 |
Plastics-coated fabrics for upholstery — Part 3: Specification for polyurethane-coated woven fabrics |
Specifies requirements for polyurethane-coated fabrics for upholstered furniture, where a substantially continuous coating is applied to one side of the fabric. Two annexes for the selection of the specimen and for the determination of the resistance to print wear. Part 1 of this standard: PVC-coated knitted fabrics; part 2: PVC-coated woven fabrics.
|
Published |
1988-06 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
97.140
Furniture
;
59.080.40
Coated fabrics
|
| ISO 7854:1995 |
Rubber- or plastics-coated fabrics — Determination of resistance to damage by flexing |
Describes the De Mattia method, Schildknecht method and crumple/flex method for the assessment of the resistance of coated fabrics to damage by repeated flexing. Cancels and replaces the first edition, which has been technically revised.
|
Published |
1995-08 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 8095:1990 |
PVC-coated fabrics for tarpaulins — Specification |
|
Published |
1990-06 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 8096-1:1989 |
Rubber- or plastics-coated fabrics for water-resistant clothing — Specification — Part 1: PVC-coated fabrics |
This part of ISO 8096 specifies requirements for fabrics coated on one or both sides with suitably plasticized coating, pigmented or otherwise provided with additions of vinyl chloride or copolymer the major constituent of which is vinyl chloride, and which are suitable for use in the making up of water-resistant clothing.
|
Withdrawn |
1989-06 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 8096-1:1989/Cor 1:1991 |
Rubber- or plastics-coated fabrics for water-resistant clothing — Specification — Part 1: PVC-coated fabrics — Technical Corrigendum 1 |
|
Withdrawn |
1991-08 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 8096-2:1989 |
Rubber- or plastics-coated fabrics for water-resistant clothing — Specification — Part 2: Polyurethane- and silicone elastomer-coated fabrics |
This part of ISO 8096 specifies requirements for fabrics coated on one side with a polyurethane or silicone elastomer or a coating the major constituent of which is a polyurethane or silicone elastomer and intended for use in water-resistant clothing.
|
Withdrawn |
1989-07 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 8096-3:1988 |
Rubber- or plastics-coated fabrics for water-resistant clothing — Specification — Part 3: Natural rubber- and synthetic rubber-coated fabrics |
This part of ISO 8096 specifies requirements for fabrics coated in one or both sides or for double-texture fabrics in which a natural rubber or synthetic polymer of a type other than those specified in ISO 8096-1 and ISO 8096-2 is used and which are primarily intended for water-resistant clothing.
|
Withdrawn |
1988-05 |
Edition : 1 |
Number of pages : 17 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 8096:2005 |
Rubber- or plastics-coated fabrics for water-resistant clothing — Specification |
ISO 8096:2005 specifies the requirements for water vapour permeable and non water vapour permeable coated fabrics suitable for use in the construction of water penetration resistant clothing. The standard does not address the method of fabrication of the garment.
|
Published |
2005-02 |
Edition : 1 |
Number of pages : 23 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 8096:2005/Cor 1:2005 |
Rubber- or plastics-coated fabrics for water-resistant clothing — Specification — Technical Corrigendum 1 |
|
Published |
2005-07 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO/CD 17581 |
Rubber- or plastics-coated fabrics — Determination of water absorption resistance |
This document specifies two test methods for the determination of water absorption resistance of rubber – or plastics-coated fabrics.
－Method A: Method using red ink (apply to coated fabric where water absorption phenomenon can be visually obserbed)
－Method B: Method using a water detection test paper
|
Under development |
|
Edition : 1 |
|
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 22751:2020 |
Rubber- or plastic-coated fabrics — Physical and mechanical test — Determination of bending force |
This document specifies a test method for the determination of the bending force of rubber or plastics-coated fabrics.
|
Published |
2020-08 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 32100:2010 |
Rubber- or plastics-coated fabrics — Physical and mechanical tests — Determination of flex resistance by the flexometer method |
ISO 32100:2010 specifies a test method for determining the flex resistance of rubber- or plastics-coated fabrics in the folded condition. The test method is applicable only to products which can be clamped in the test apparatus used and to products with which the fold made in the test specimen can be caused to move back and forth along the specimen during the test.
|
Withdrawn |
2010-12 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 32100:2018 |
Rubber- or plastics-coated fabrics — Physical and mechanical tests — Determination of flex resistance by the flexometer method |
This document specifies a test method for determining the flex resistance of rubber- or plastics‑coated fabrics in the folded condition. The test method is applicable only to products which can be clamped in the test apparatus used and to products with which the fold made in the test specimen can be caused to move back and forth along the specimen during the test.
The appearance of the test specimen, after completion of either the flex number (see 3.1) or a specified number of flex cycles, is taken as a measure of the flex resistance in the folded condition.
|
Published |
2018-10 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
59.080.40
Coated fabrics
|
| ISO 2816:1973 |
Fundamental characteristics of a system of shoe sizing to be known as Mondopoint |
|
Withdrawn |
1973-05 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
61.060
Footwear
|
| ISO 3355:1975 |
Shoe sizes — System of length grading (for use in the Mondopoint system) |
|
Withdrawn |
1975-01 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
61.060
Footwear
|
| ISO/TR 3836:1978 |
Shoe sizes — System of width grading (for use in the Mondopoint system) |
|
Withdrawn |
1978-02 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
61.060
Footwear
|
| ISO 3844:1977 |
Shoe sizes — Method of marking |
|
Withdrawn |
1977-08 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
61.060
Footwear
|
| ISO 3910:1983 |
Rubber boots, unlined moulded |
Lays down the requirements for general purpose products, manufactured in one piece. Two figures show the details of the boot and the test piece, respectively. 4 tables give the minimum thicknesses, tensile strength and elongation at break before and after ageing and the flexing test limits. The method of testing resistance to flexing is described in an annex. - Replaces the first edition (ISO 3910-1976).
|
Withdrawn |
1983-05 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
61.060
Footwear
|
| ISO 5403-1:2011 | IULTCS/IUP 10-1 |
Leather — Determination of water resistance of flexible leather — Part 1: Repeated linear compression (penetrometer) |
ISO 5403-1:2011 specifies a method for determining the dynamic water resistance of leather by means of repeated linear compression. It is applicable to all flexible leathers but is particularly suitable for leathers intended for footwear applications.
|
Published |
2011-12 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
61.060
Footwear
;
59.140.30
Leather and furs
|
| ISO 5403-2:2011 | IULTCS/IUP 10-2 |
Leather — Determination of water resistance of flexible leather — Part 2: Repeated angular compression (Maeser) |
ISO 5403-2:2011 specifies a method for determining the dynamic water resistance of leather by means of repeated angular compression. It is applicable to all flexible leathers but is particularly suitable for leathers intended for footwear applications. It uses a Maeser-type machine and includes an option for electronic detection.
|
Published |
2011-12 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
61.060
Footwear
;
59.140.30
Leather and furs
|
| ISO 5403:2002 | IULTCS/IUP 10 |
Leather — Physical and mechanical tests — Determination of water resistance of flexible leather |
ISO 5403:2002 specifies a method for determining the dynamic water resistance of leather. It is applicable to all flexible leathers but is particularly suitable for leathers intended for footwear uppers.
|
Withdrawn |
2002-12 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
61.060
Footwear
;
59.140.30
Leather and furs
|
| ISO 6907:1984 |
Rubber footwear — Vulcanized resin rubber and vulcanized hard rubber soling materials — Specification |
|
Withdrawn |
1984-05 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
61.060
Footwear
|
| ISO 6907:1994 |
Rubber footwear — Vulcanized resin rubber and vulcanized high-hardness rubber soling materials — Specification |
Cancels and replaces the first edition (1984). Lays down requirements for two grades of resin rubber and high-hardness rubber soling materials, for soling without a heavy pattern, for use on footwear: grade 1 - men's, boys' and girls' footwear; grade 2 - women's footwear, footwear for light use, such as indoor footwear, including slippers.
|
Withdrawn |
1994-11 |
Edition : 2 |
Number of pages : 5 |
Technical Committee |
61.060
Footwear
|