| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO 20873:2001 |
Footwear — Test methods for outsoles — Dimensional stability |
ISO 20873 specifies a method for the determination of the linear shrinkage after heating of test specimens prepared from outsoles.
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
61.060
Footwear
|
| ISO 20873:2018 |
Footwear — Test methods for outsoles — Dimensional stability |
ISO 20873:2018 specifies a method for determining the linear shrinkage after heating of test specimens prepared from outsoles.
|
Published |
2018-03 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
61.060
Footwear
|
| ISO 20874:2001 |
Footwear — Test methods for outsoles — Needle tear strength |
ISO 20874 specifies a method for the determination of the needle tear strength for outsoles, irrespective of the material.
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
61.060
Footwear
|
| ISO 20874:2018 |
Footwear — Test methods for outsoles — Needle tear strength |
ISO 20874:2018 specifies a method for the determination of the needle tear strength for outsoles, irrespective of the material.
|
Published |
2018-03 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
61.060
Footwear
|
| ISO 20876:2001 |
Footwear — Test methods for insoles — Resistance to stitch tear |
ISO 20876 describes a method of evaluating the ability of an insole, irrespective of the material, to hold stitches or to take clenched metal fastenings. The method has become accepted as a general quality criterion for insole materials even where attachment is by means of adhesives.
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
61.060
Footwear
|
| ISO 20876:2018 |
Footwear — Test methods for insoles — Resistance to stitch tear |
ISO 20876:2018 describes a method for evaluating the ability of an insole, irrespective of the material, to hold stitches, or to take clenched metal fastenings. The method has become accepted as a general quality criterion for insole materials even where attachment is by means of adhesives.
|
Published |
2018-03 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
61.060
Footwear
|
| ISO 20877:2001 |
Footwear — Test methods for whole shoe — Thermal insulation |
ISO 20877 describes a method of measuring footwear insulation against cold.
It applies to all types of closed footwear.
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
61.060
Footwear
|
| ISO 20877:2011 |
Footwear — Test methods for whole shoe — Thermal insulation |
ISO 20877:2011 specifies a method for measuring insulation of footwear against heat or cold, in order to provide information for assessing footwear comfort.
ISO 20877:2011 is applicable to all types of closed footwear or boots, except footwear used as personal protective equipment.
|
Published |
2011-09 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
61.060
Footwear
|
| ISO/TR 20879:2007 |
Footwear — Performance requirements for components for footwear — Uppers |
ISO/TR 20879:2007 establishes the performance requirements for uppers component for footwear (not for the finished footwear), irrespective of the material, in order to assess the suitability for the end use. It also establishes the test methods to be used to evaluate the compliance with the requirements.
This Technical Report applies to uppers for various kinds of footwear.
ISO/TR 20879:2007 is intended to be used as a reference between the footwear manufacturer and the supplier. It is not intended for third party certification of finished shoes destined for the consumer.
|
Published |
2007-02 |
Edition : 1 |
Number of pages : 19 |
Technical Committee |
61.060
Footwear
|
| ISO/CD TR 20879 |
Footwear — Performance requirements for components for footwear — Uppers |
|
Deleted |
|
Edition : 2 |
|
Technical Committee |
61.060
Footwear
|
| ISO/TR 20880:2007 |
Footwear — Performance requirements for components for footwear — Outsoles |
ISO/TR 20880:2007 establishes the performance requirements for outsoles components for footwear (not for the finished footwear), irrespective of the material, in order to assess the suitability for the end use. It also establishes the test methods to be used to evaluate the compliance with the requirements.
This Technical Report applies to outsoles for various kinds of footwear.
ISO/TR 20880:2007 is intended to be used as a reference between the footwear manufacturer and the supplier. It is not intended for third party certification of finished shoes destined for the consumer.
|
Published |
2007-02 |
Edition : 1 |
Number of pages : 15 |
Technical Committee |
61.060
Footwear
|
| ISO/CD TR 20880 |
Footwear — Performance requirements for components for footwear — Outsoles |
|
Deleted |
|
Edition : 2 |
|
Technical Committee |
61.060
Footwear
|
| ISO/TR 20881:2007 |
Footwear — Performance requirements for components for footwear — Insoles |
ISO/TR 20881:2007 establishes the performance requirements for insoles components for footwear (not for the finished footwear), irrespective of the material, in order to assess the suitability for the end use and/or fitness for purpose. It also establishes the test methods to be used to evaluate the compliance with the requirements.
This Technical Report applies to insoles for various kinds of footwear.
ISO/TR 20881:2007 is intended to be used as a reference between the manufacturer and the supplier. It is not intended for third party certification.
|
Published |
2007-02 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
61.060
Footwear
|
| ISO/CD TR 20881 |
Footwear — Performance requirements for components for footwear — Insoles |
|
Deleted |
|
Edition : 2 |
|
Technical Committee |
61.060
Footwear
|
| ISO/TR 20882:2007 |
Footwear — Performance requirements for components for footwear — Lining and insocks |
ISO/TR 20882:2007 establishes the performance requirements for lining and insock components for footwear (not for finished footwear), irrespective of the material, in order to assess the suitability for the end use and/or fitness for purpose. It also establishes the test methods to be used to evaluate the compliance with the requirements.
This Technical Report applies to lining and insocks for various kinds of footwear.
ISO/TR 20882:2007 is intended to be used as a reference between the manufacturer and the supplier. It is not intended for third party certification.
|
Published |
2007-02 |
Edition : 1 |
Number of pages : 20 |
Technical Committee |
61.060
Footwear
|
| ISO/CD TR 20882 |
Footwear — Performance requirements for components for footwear — Lining and insocks |
|
Deleted |
|
Edition : 2 |
|
Technical Committee |
61.060
Footwear
|
| ISO/TR 20883:2007 |
Footwear — Performance requirements for components for footwear — Shanks |
ISO/TR 20883:2007 establishes the performance requirements for shanks components for footwear (not for finished footwear), irrespective of the material, in order to assess the suitability for the end use and/or fitness for purpose. It also establishes the test methods to be used to evaluate the compliance with the requirements.
This Technical Report applies to shanks for various kinds of footwear.
ISO/TR 20883:2007 is intended to be used as a reference between the manufacturer and the supplier. It is not intended for third party certification of finished shoes destined for the consumer.
|
Published |
2007-02 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
61.060
Footwear
|
| ISO/CD TR 20883 |
Footwear — Performance requirements for components for footwear — Shanks |
|
Deleted |
|
Edition : 2 |
|
Technical Committee |
61.060
Footwear
|
| ISO 21061:2021 |
Footwear — Chemical tests — General principles on the preparation of samples |
This document specifies a range of procedures for the sample preparation of footwear and footwear components to carry out chemical tests. It further specifies how to designate the samples.
The sampling procedures specified are designed to allow concurrent chemical testing for footwear
This document is applicable to all types of footwear and footwear components.
|
Published |
2021-11 |
Edition : 1 |
Number of pages : 17 |
Technical Committee |
61.060
Footwear
|
| ISO/TR 22648:2007 |
Footwear — Performance requirements for components for footwear — Stiffeners and toepuffs |
ISO/TR 22648:2007 establishes the performance requirements for stiffener and toepuff components for footwear (not for finished footwear), irrespective of the material, in order to assess the suitability for the end use and/or fitness for purpose. It also establishes the test methods to be used to evaluate the compliance with the requirements.
This Technical Report applies to stiffeners and toepuffs for various kinds of footwear.
ISO/TR 22648:2007 is intended to be used as a reference between the manufacturer and the supplier. It is not intended for third party certification of finished shoes destined for the consumer.
|
Published |
2007-02 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
61.060
Footwear
|
| ISO/CD TR 22648 |
Footwear — Performance requirements for components for footwear — Stiffeners and toepuffs |
|
Deleted |
|
Edition : 2 |
|
Technical Committee |
61.060
Footwear
|
| ISO 22649:2003 |
Footwear — Test methods for insoles and insocks — Water absorption and desorption |
ISO 22649:2003 specifies two test methods for determining the water absorption and desorption of insoles and insocks, irrespective of the material. These methods are:
Method A: Determination of the static water absorption and desorption of insoles and insocks. Method B: Determination of the dynamic water absorption and desorption of insoles.
|
Withdrawn |
2003-11 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
61.060
Footwear
|
| ISO 22649:2016 |
Footwear — Test methods for insoles and insocks — Water absorption and desorption |
ISO 22649:2016 specifies two test methods for determining the water absorption and desorption of insoles and insocks, irrespective of the material.
These methods are as follows.
- Method A: Determination of the static water absorption and desorption of insoles and insocks.
- Method B: Determination of the dynamic water absorption and desorption of insoles and insocks.
|
Published |
2016-05 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
61.060
Footwear
|
| ISO 22650:2002 |
Footwear — Test methods for whole shoe — Heel attachment |
ISO 22650 specifies a method for the determination of the heel attachment of footwear and applies to women's medium- and high-heeled footwear.
This test method measures three related wear properties:
the rigidity of the shoe backpart during normal walking;the amount of permanent deformation of the backpart caused by a fairly large force applied to the heel in a backward direction;the force required to detach the heel.
|
Withdrawn |
2002-09 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
61.060
Footwear
|
| ISO 22650:2018 |
Footwear — Test methods for whole shoe — Heel attachment |
ISO 22650:2018 specifies a method for the determination of the heel attachment of footwear. It applies to woman's medium and high heeled footwear.
This test method measures three related wear properties:
- the rigidity of the shoe backpart during normal walking;
- the amount of permanent deformation of the backpart caused by a fairly large force applied to the heel in a backward direction;
- the force required to detach the heel.
|
Published |
2018-03 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
61.060
Footwear
|
| ISO 22651:2002 |
Footwear — Test methods for insoles — Dimensional stability |
ISO 22651 specifies a method for the determination of the dimensional stability of insoles, irrespective of the material, after immersion in water.
|
Published |
2002-09 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
61.060
Footwear
|
| ISO 22652:2002 |
Footwear — Test methods for insoles, lining and insocks — Perspiration resistance |
ISO 22652 specifies a method for the determination of the ageing of insoles, lining or insocks, caused by human sweat.
|
Published |
2002-09 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
61.060
Footwear
|
| ISO 22654:2002 |
Footwear — Test methods for outsoles — Tensile strength and elongation |
ISO 22654 specifies a method for the determination of the tensile strength and elongation of outsoles.
|
Published |
2002-06 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
61.060
Footwear
|
| ISO 22774:2004 |
Footwear — Test methods for accessories: shoe laces — Abrasion resistance |
ISO 22774:2004 specifies three test methods for determining the abrasion resistance of a shoelace, on repeated rubbing:
method 1: lace to lace abrasion;
method 2: lace to standard eyelet abrasion;
method 3: lace to eyelet (from footwear) abrasion.
|
Published |
2004-12 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
61.060
Footwear
|
| ISO 22775:2004 |
Footwear — Test methods for accessories: Metallic accessories — Corrosion resistance |
ISO 22775:2004 specifies two methods for determining the propensity of a metal surface to either change visually due to contamination by atmospheric pollution (Method 1: sulfide tarnishing), or to corrode due to the action of salt water (Method 2: salt water corrosion).
|
Published |
2004-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
61.060
Footwear
|
| ISO 22776:2004 |
Footwear — Test methods for accessories: Touch and close fasteners — Shear strength before and after repeated closing |
ISO 22776:2004 specifies a test method for determining the longitudinal shear strength of touch and close fasteners before and after repeated use.
|
Published |
2004-12 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
61.060
Footwear
|
| ISO 22777:2004 |
Footwear — Test methods for accessories: Touch and close fasteners — Peel strength before and after repeated closing |
ISO 22777:2004 specifies a test method for determining the peel strength of touch and close fasteners before and after repeated use.
|
Published |
2004-12 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
61.060
Footwear
|
| ISO 24263:2020 |
Footwear — Attachment strength of straps, trims and accessories |
This document specifies a method for determining the attachment strength of footwear upper straps joined to the sole, hooks, eyelets and trims.
|
Published |
2020-10 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
61.060
Footwear
|
| ISO 24264:2020 |
Footwear — Test methods for hollow and compact heels with top pieces — Top piece attachment strength |
This document specifies a method for determining the attachment pull-out strength of heel top pieces.
This method is applicable to all kind of heels with top pieces.
|
Published |
2020-10 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
61.060
Footwear
|
| ISO 24265:2020 |
Footwear — Test methods for uppers — Resistance to rubbing using a rubber strip |
This document specifies a method for the determination of the rubbing resistance of leather and synthetic materials using rubber.
The method aims to establish testing conditions that are similar to those of the practical use of footwear subjected to drastic stress, as is the case of hiking or children's footwear, where the upper of one of the shoes is expected to rub with the sole of the other.
This method is applicable to all types of leather and synthetic materials intended for shoe uppers.
|
Published |
2020-10 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
61.060
Footwear
|
| ISO 24266:2020 |
Footwear — Test methods for whole shoe — Flexing durability |
This document specifies two test methods for the determination of the flexing durability of whole shoes. The two methods might not give comparable results.
NOTE The selected test method depends on agreement between relative parties who use this test method or product standards which reference this test method.
These methods are not applicable to the whole shoes with heel height more than 50 mm, or the thickness of flexing area of the soles more than 25 mm, or flexing angle less than 45° according to ISO 17707:2005, Clause 6.
|
Published |
2020-11 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
61.060
Footwear
|
| ISO 24267:2020 |
Footwear — Determination of coefficient of friction for footwear and sole components — Test method |
This document provides a method for determining the coefficient of friction between footwear and floorings under conditions simulating those experienced in the phases of a typical walking step when slip is most likely to occur.
The method is applicable to all types of footwear and footwear components, outsole units, heel top pieces (top lifts) and sheet soling materials, excepting PPE footwear (Personal Protective Equipment) and special purpose footwear containing spikes, metal studs or similar.
|
Published |
2020-11 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
61.060
Footwear
|
| ISO 4578:1979 |
Adhesives — Determination of peel resistance of high-strength adhesive bonds — Floating roller method |
|
Withdrawn |
1979-04 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
83.180
Adhesives
|
| ISO 4578:1990 |
Adhesives — Determination of peel resistance of high-strength adhesive bonds — Floating roller method |
|
Withdrawn |
1990-03 |
Edition : 2 |
Number of pages : 3 |
Technical Committee |
83.180
Adhesives
|
| ISO 4578:1997 |
Adhesives — Determination of peel resistance of high-strength adhesive bonds — Floating-roller method |
This International Standard specifies a floating-roller method for the determination of the peel resistance of high-strength adhesive bonds between a rigid adherend and a flexible adherend when tested under specified conditions of preparation and testing.
Note - There are indications that the floating roller may produce more constant numerical data than other peel methods. However, it should not be expected that the flexible adherend will conform to the surface of the roller.
|
Published |
1997-07 |
Edition : 3 |
Number of pages : 6 |
Technical Committee |
83.180
Adhesives
|
| ISO 4587:1979 |
Adhesives — Determination of tensile lap-shear strength of high strength adhesive bonds |
|
Withdrawn |
1979-02 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
83.180
Adhesives
|
| ISO 4587:1995 |
Adhesives — Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies |
Specifies a method for determining the tensile lap-shear strength of rigid-to-rigid bonded assemblies when tested using a standard specimen and under specified conditions. Cancels and replaces the first edition.
|
Withdrawn |
1995-08 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
83.180
Adhesives
|
| ISO 4587:2003 |
Adhesives — Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies |
ISO 4587:2003 specifies a method for determining the tensile lap-shear strength of rigid-to-rigid bonded assemblies using a standard specimen under specified conditions of preparation and testing. This test procedure does not provide design information.
|
Published |
2003-03 |
Edition : 3 |
Number of pages : 4 |
Technical Committee |
83.180
Adhesives
|
| ISO 4588:1989 |
Adhesives — Preparation of metal surfaces for adhesive bonding |
|
Withdrawn |
1989-10 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
83.180
Adhesives
|
| ISO 4588:1995 |
Adhesives — Guidelines for the surface preparation of metals |
Describes the usual procedures for the laboratory preparation of metal surfaces for adhesive bonding and testing of the bond. Prebonding surface treatments are given for aluminium and aluminium alloys, chromium, copper and nickel and their alloys, magnesium and magnesium alloys, mild and stainless steel, tin, zinc and zinc alloys.
|
Withdrawn |
1995-11 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
83.180
Adhesives
|
| ISO 5684:2023 |
Adhesives — Floor covering adhesives and products for flooring installation — Assessment and classification of low volatile organic compound (VOC) products |
This document specifies a reference method for the determination of volatile organic compound (VOC) emissions into indoor air from floor covering adhesives and products used for flooring installation. This method is applicable to determine volatile organic compounds, semi-volatile organic compounds, and volatile aldehydes. It is based on the use of a test chamber and subsequent analysis of an air sample for organic compounds by GC-MS respectively HPLC.
The main purpose of the test procedure is to obtain relevant performance data for the classification of flooring adhesives and products used for the installation of floor coverings with respect to low VOC emissions during the use phase of the flooring.
NOTE 1: This document describes the overall procedure and makes use of existing standards mainly by normative reference, complemented when necessary with additional or modified normative requirements.
NOTE 2: No conclusions about occupational health and safety can be drawn from the testing and/or the classification of products according to this standard.
|
Published |
2023-04 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
83.180
Adhesives
|
| ISO 6076 |
Adhesives — Installation of floor coverings, wood flooring, levelling compounds and tiles — Specification of trowel notch sizes |
|
Under development |
2023-04 |
Edition : 1 |
|
Technical Committee |
83.180
Adhesives
|
| ISO 6237:1987 |
Adhesives — Wood-to-wood adhesive bonds — Determination of shear strength by tensile loading |
The method is intended for testing adhesives used in bonding wood to wood. Standard specimens are prepared from timber plies. The test specimens shall be of a two-ply or three-ply construction with notches as shown in a picture. The shear area is 20 mm x 25 mm. The adhesive shall be applied in accordance with the procedure recommended by the manufacturer of the adhesive. The mean tensile shear strength and the standard deviation of test results shall be reported.
|
Withdrawn |
1987-03 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
83.180
Adhesives
|
| ISO 6237:2003 |
Adhesives — Wood-to-wood adhesive bonds — Determination of shear strength by tensile loading |
ISO 6237:2003 specifies a method for determining the shear strength of wood-to-wood adhesive bonds, with a standard specimen loaded in tension and under specified conditions of preparation, conditioning and testing. This method is intended for testing only those adhesives used in bonding wood to wood in either parallel-laminated or cross-laminated construction. It is not intended for use in testing manufactured products.
|
Withdrawn |
2003-10 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
83.180
Adhesives
|
| ISO 14676:1997 |
Adhesives — Evaluation of the effectiveness of surface treatment techniques for aluminium — Wet-peel test by floating-roller method |
This International Standard is applicable to the evaluation of the quality of a surface treatment of aluminium or its alloys for high-strength adhesive bonding.
|
Published |
1997-07 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
83.180
Adhesives
|
| ISO 6237:2017 |
Adhesives — Wood-to-wood adhesive bonds — Determination of shear strength by tensile loading |
ISO 6237:2017 specifies a method for determining the shear strength of wood-to-wood adhesive bonds, with a standard specimen loaded in tension and under specified conditions of preparation, conditioning and testing. This method is intended for testing only those adhesives used in bonding wood to wood in either parallel-laminated or cross-laminated construction.
This method is not intended for use in testing manufactured products.
|
Published |
2017-11 |
Edition : 3 |
Number of pages : 10 |
Technical Committee |
83.180
Adhesives
|
| ISO 6238:1987 |
Adhesives — Wood-to-wood adhesive bonds — Determination of shear strength by compression loading |
|
Withdrawn |
1987-03 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
83.180
Adhesives
|
| ISO 6238:2001 |
Adhesives — Wood-to-wood adhesive bonds — Determination of shear strength by compressive loading |
|
Withdrawn |
2001-02 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
83.180
Adhesives
|
| ISO 6238:2018 |
Adhesives — Wood-to-wood adhesive bonds — Determination of shear strength by compressive loading |
This document specifies a method for determining the shear strength of wood-to-wood adhesive bonds, with a standard specimen loaded in compression and under specified conditions of preparation, conditioning and testing. This method is intended for testing only those adhesives used in bonding wood to wood.
This method is not intended for use in testing manufactured products.
|
Published |
2018-08 |
Edition : 3 |
Number of pages : 10 |
Technical Committee |
83.180
Adhesives
|
| ISO 6354:1982 |
Adhesives — Vocabulary |
|
Withdrawn |
1982-05 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
83.180
Adhesives
;
01.040.83
Rubber and plastics industries (Vocabularies)
|
| ISO 6922:1987 |
Adhesives — Determination of tensile strength of butt joints |
Specifies a method for determining the bond strength of a butt joint when subjected to tensile force. The method is applicable to all types of adhesives. -A joint formed from two bar or rod adherends bonded by faces normal to their length is stressed to rupture by a tensile force. The test result is expressed as the arithmetic mean of the breaking force of five valid tests.
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
83.180
Adhesives
|
| ISO 7387-1:1983 |
Adhesives with solvents for assembly of PVC-U pipe elements — Characterization — Part 1: Basic test methods |
Specification of three basic test methods, which are essential in deciding the uniformity of an adhesive: Viscosity (dynamic and Brookfield viscosity), conventional dry matter content and ash content.
|
Published |
1983-09 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
83.180
Adhesives
|
| ISO/FDIS 7972 |
Adhesives — Absorption of water into an adhesive layer using an open-faced specimen and determination of shear strength by secondary bonding |
This standard specifies a method for the rapid infusion of water to an adhesive layer using a specimen with one side open, the secondary bonding the specimens with the adhesive layer that is still moistened, and a shear strength test of the secondary bonded specimen. This test procedure does not provide design information.
|
Under development |
|
Edition : 1 |
Number of pages : 10 |
Technical Committee |
83.180
Adhesives
|
| ISO 8510-1:1990 |
Adhesives — Peel test for a flexible-bonded-to-rigid test specimen assembly — Part 1: 90 degree peel |
Particularly suitable for use with less flexible adherends for which a 180 ° peel test is not suitable because the adherends crack, break or delaminate. A bonded assembly of two adherends is prepared using the adhesive under test. The adherends are then pulled apart at a steady rate, starting at the open end of the bond, in such a way that separation occurs progressively along the length of the bonded adherends. The force is applied approximately normal to the plane of the bond, through the separated part of the flexible adherend. A figure shows a schematic diagram.
|
Withdrawn |
1990-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
83.180
Adhesives
|
| ISO 8510-2:1990 |
Adhesives — Peel test for a flexible-bonded-to-rigid test specimen assembly — Part 2: 180 degree peel |
Suitable for use with less flexible adherends. The principle consists in preparing a bonded assembly of two adherends, using the adhesive under test. The adherends are then pulled apart at a steady rate, starting at the open end of the bond, in such a way that separation occurs progressively along the length of the bonded adherends. The force is applied substantially parallel to the plane of the bond, through the separated part of the flexible adherend. A figure shows a schematic diagram.
|
Withdrawn |
1990-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
83.180
Adhesives
|
| ISO 8510-2:2006 |
Adhesives — Peel test for a flexible-bonded-to-rigid test specimen assembly — Part 2: 180° peel |
ISO 8510-2:2006 specifies a 180° peel test for the determination, under specified conditions, of the peel resistance of a bonded assembly of two adherends where one adherend is flexible and the other is rigid.
|
Published |
2006-12 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
83.180
Adhesives
|
| ISO 9142:1990 |
Adhesives — Guide to the selection of standard laboratory ageing conditions for testing bonded joints |
Describes conditions under which adhesive joints may be exposed to various climatic or chemical influences for the purpose of assessing the effects of such influences on certain properties. They are not necessarily applicable to the determination of the service life of a bonded assembly. The principle consists in defining the ageing conditions that relate most closely to the application for the adhesive by reference to the preferred conditions set out in annex A to annex F. These conditions are single-variable, multi-variable, cyclic, change of heat, cold (thermal shock), humidity, dryness, immersion in water or salt solutions, exposure to chemical attack and combinations of these.
|
Withdrawn |
1990-12 |
Edition : 1 |
Number of pages : 20 |
Technical Committee |
83.180
Adhesives
|
| ISO 9142:1990/Cor 1:1995 |
Adhesives — Guide to the selection of standard laboratory ageing conditions for testing bonded joints — Technical Corrigendum 1 |
Corrects the content of some subclauses.
|
Withdrawn |
1995-12 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
83.180
Adhesives
|
| ISO 9142:2003 |
Adhesives — Guide to the selection of standard laboratory ageing conditions for testing bonded joints |
ISO 9142:2003 describes laboratory ageing conditions under which adhesive joints may be exposed to various environmental influences -- climatic or chemical -- for the purpose of assessing the effects of such influences on certain properties.
The ageing conditions are applicable to bonded assemblies and may be used to constitute a set of tests for the evaluation of an adhesive.
The results obtained using the procedures described in this International Standard are not necessarily applicable to the determination of the service life of a bonded assembly because there is no direct relation between the test results and the behaviour of a bonded assembly over a period of time under service conditions. However, for certain specific applications, experience with the procedures may enable a correlation to be established.
|
Published |
2003-12 |
Edition : 2 |
Number of pages : 24 |
Technical Committee |
83.180
Adhesives
|
| ISO 9311-1:2005 |
Adhesives for thermoplastic piping systems — Part 1: Determination of film properties |
ISO 9311-1:2005 specifies three test procedures suitable for the determination of the spreadability and film properties of solvent-containing adhesives for thermoplastic piping systems. These methods do not produce directly comparable results. One method is applicable to non-thixotropic adhesives and the other two methods are applicable to thixotropic adhesives.
|
Published |
2005-08 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
83.180
Adhesives
;
23.040.01
Pipeline components and pipelines in general
|
| ISO 9311-2:2002 |
Adhesives for thermoplastic piping systems — Part 2: Determination of shear strength |
|
Withdrawn |
2002-08 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
83.180
Adhesives
;
23.040.01
Pipeline components and pipelines in general
|
| ISO 9311-2:2011 |
Adhesives for thermoplastic piping systems — Part 2: Determination of shear strength |
ISO 9311-2:2011 specifies a method for the determination of the shear strength of joints made with adhesives for thermoplastic piping systems.
|
Published |
2011-08 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
83.180
Adhesives
;
23.040.01
Pipeline components and pipelines in general
|
| ISO 9311-3:2005 |
Adhesives for thermoplastic piping systems — Part 3: Test method for the determination of resistance to internal pressure |
ISO 9311-3:2005 specifies a method for the assessment of the internal pressure resistance of assemblies made with adhesives for thermoplastic piping systems.
|
Published |
2005-03 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
83.180
Adhesives
;
23.040.01
Pipeline components and pipelines in general
|
| ISO 9653:1991 |
Adhesives — Test method for shear impact strength of adhesive bonds |
|
Withdrawn |
1991-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
83.180
Adhesives
|
| ISO 9653:1998 |
Adhesives — Test method for shear impact strength of adhesive bonds |
|
Published |
1998-08 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
83.180
Adhesives
|
| ISO 9664:1993 |
Adhesives — Test methods for fatigue properties of structural adhesives in tensile shear |
The principle of the method specified is cyclically stressing the specimen in a way that may be regarded as the superposition of an alternating stress on a static stress which is the mean stress. The number of cycles at failure of the specimen for a given mean stress and stress amplitude is determined. These values are used to establish SN curves which then permit the estimation of the confidence zone concerning the fatigue resistance of a joint. The fatigue properties are a function of the specimen geometry. The results do not correspond to intrinsic properties of the adhesive and cannot be used for design purposes.
|
Published |
1993-05 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
83.180
Adhesives
|
| ISO 9665:1993 |
Adhesives — Animal glues — Methods for sampling and testing |
|
Withdrawn |
1993-03 |
Edition : 1 |
Number of pages : 17 |
Technical Committee |
83.180
Adhesives
|
| ISO 10123:1990 |
Adhesives — Determination of shear strength of anaerobic adhesives using pin-and-collar specimens |
Also applicable to liquid adhesives used for locking and sealing threaded fasteners and to other adhesives. The test is for ranking and quality control of adhesives; the result does not reflect the performance of the materials in service. Determination of the force required to shear the adhesive joint formed between a metal pin and a metal collar. The static shear strength is calculated from this force.
|
Withdrawn |
1990-11 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
83.180
Adhesives
|
| ISO 10123:2013 |
Adhesives — Determination of shear strength of anaerobic adhesives using pin-and-collar specimens |
ISO 10123:2013 specifies a method for the determination of the shear strength of anaerobic-curing liquid adhesives used for retaining cylindrical assemblies, pin-and-collar type, or for locking and sealing threaded fasteners. This test method can also be used for other adhesives.
|
Published |
2013-11 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
83.180
Adhesives
|
| ISO 10354:1992 |
Adhesives — Characterization of durability of structural-adhesive-bonded assemblies — Wedge rupture test |
Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates. The test is applicable at the present time to the bonding of aluminium and titanium alloys, but may be used for other metals and plastics, provided consideration is given to the thickness and rigidity of the adherends.
|
Published |
1992-04 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
83.180
Adhesives
|
| ISO 10363:1992 |
Hot-melt adhesives — Determination of thermal stability |
The method is based on placing a stainless steel or glass vessel in an oil bath or oven, adding a sufficient quantity of the adhesive to the vessel, melting the sample, measuring the viscosity at the operating temperature and the softening point, repeating these operations at regular time intervals of between 4 h and 6 h, until the time for stopping the test according to pre-determined criteria is reached, and observing and recording, at the time that each measurement is taken, the following phenomena: skin formation, fumes, phase separation, gelation, change in colour.
|
Published |
1992-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
83.180
Adhesives
|
| ISO 10364:1993 |
Adhesives — Determination of working life (pot life) of multi-component adhesives |
Is intended to determine whether the working life conforms to the minimum specified working life required of an adhesive by viscosity tests or by bond strength tests or by both. The working life is determined by measuring the viscosity and/or bond strength at specified intervals. The time at which the bond strength drops to a specified level and/or a specified change in viscosity is obtained is considered the working life of the adhesive.
|
Withdrawn |
1993-06 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
83.180
Adhesives
|
| ISO 10364:2007 |
Structural adhesives — Determination of the pot life (working life) of multi-component adhesives |
ISO 10364:2007 specifies methods for determining the pot life of multi-component adhesives in order to be able to determine whether the pot life conforms to the minimum specified working life required of an adhesive.
The test methods described are suitable for assessing all multi-component adhesives, and especially epoxy-based and polyurethane-based adhesives, but they are not suitable for some acrylic-based adhesives.
The methods can also be used for assessing non-structural adhesives.
|
Withdrawn |
2007-09 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
83.180
Adhesives
|
| ISO 10364:2015 |
Structural adhesives — Determination of the pot life (working life) of multi-component adhesives |
ISO 10364:2015 specifies methods for determining the pot life of multi-part adhesives in order to be able to determine whether the pot life conforms to the minimum specified working life required of an adhesive.
For the purposes of simplification, the term "pot life" is deemed to have the same meaning as "working life" and will be used to represent both throughout this International Standard. Methods described to measure the property provide different answers. So the results shall be specified with respect to the method used.
The test methods described are suitable for assessing all multi?part adhesives, and especially epoxy based and polyurethane based adhesives, but they are not suitable for some acrylic-based adhesives.
NOTE 1 Some of the methods described in this International Standard can also be suitable for determination of working life of one-part adhesives that react to humidity (e.g. PUR prepolymers).
NOTE 2 This International Standard can also be used for assessing non-structural adhesives.
|
Published |
2015-09 |
Edition : 3 |
Number of pages : 8 |
Technical Committee |
83.180
Adhesives
|
| ISO/DIS 10364 |
Structural adhesives — Determination of the pot life (working life) of multi-component adhesives |
|
Under development |
|
Edition : 4 |
Number of pages : 10 |
Technical Committee |
83.180
Adhesives
|
| ISO 10365:1992 |
Adhesives — Designation of main failure patterns |
Specifies the designations and illustrates, through diagrams, their respective appearances. It applies to all mechanical tests performed on a bonded assembly, regardless of the nature of the adherends and adhesive which make up the assembly.
|
Withdrawn |
1992-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
83.180
Adhesives
|
| ISO 834:1975/Amd 2:1980 |
Fire-resistance tests — Elements of building construction — Amendment 2 |
|
Withdrawn |
1980-09 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
13.220.50
Fire-resistance of building materials and elements
|
| ISO 10365:2022 |
Adhesives — Designation of main failure patterns |
This document specifies the designations for the main types of failure pattern of bonded assemblies and illustrates, through diagrams, their respective appearances.
This document applies to all mechanical tests performed on a bonded assembly, regardless of the nature of the adherends and adhesive which make up the assembly.
|
Published |
2022-01 |
Edition : 2 |
Number of pages : 3 |
Technical Committee |
83.180
Adhesives
|
| ISO 10964:1993 |
Adhesives — Determination of torque strength of anaerobic adhesives on threaded fasteners |
The test method described is used to make comparative assessments of the securing or locking effect of anaerobic adhesives. It may be used for other types of adhesives. Its principle is determining the torque required to unscrew a bonded nut and bolt assembly, including the initial torque required to break the bond, and the torque measured after turning the nut 180°.
|
Published |
1993-08 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
83.180
Adhesives
|
| ISO 11003-1:1993 |
Adhesives — Determination of shear behaviour of structural bonds — Part 1: Torsion test method using butt-bonded hollow cylinders |
The principle of the method specified is determining the deformation of the adhesive in the annular bond between two butt-jointed hollow cylinders as a function of the applied torque up to failure of the joint. The circular symmetry of the specimen entails a state of simple shear with uniform strain in the bond line. Shear stress values versus shear strain of the adhesive (including shear modulus) are useful for advanced design work, e.g. in finite element analysis methods.
|
Withdrawn |
1993-09 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
83.180
Adhesives
|
| ISO 11003-1:2001 |
Adhesives — Determination of shear behaviour of structural adhesives — Part 1: Torsion test method using butt-bonded hollow cylinders |
|
Withdrawn |
2001-12 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
83.180
Adhesives
|
| ISO 11003-1:2019 |
Adhesives — Determination of shear behaviour of structural adhesives — Part 1: Torsion test method using butt-bonded hollow cylinders |
This document specifies a shear test for the characterization of adhesives in a bond. The shear stress/strain properties of the adhesive (including the shear modulus) are useful for advanced design work, such as in finite element analysis methods.
|
Published |
2019-04 |
Edition : 3 |
Number of pages : 10 |
Technical Committee |
83.180
Adhesives
|
| ISO 11003-2:1993 |
Adhesives — Determination of shear behaviour of structural bonds — Part 2: Thick-adherend tensile-test method |
The test is performed on specimens consisting of thick, rigid adherends, with a short length of overlap, in order to obtain the most uniform distribution of shear stresses possible and to minimize undesired stresses. The method may be used to determine the shear properties of an adhesive (stress and strain), the shear modulus of the adhesive, all other adhesive properties that can be derived from the stress/strain curve (secant moduli, shear stress at a given strain limit, etc.), the effect of temperature, environment, testing speed, etc. on these shear properties.
|
Withdrawn |
1993-09 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
83.180
Adhesives
|
| ISO 11003-2:2001 |
Adhesives — Determination of shear behaviour of structural adhesives — Part 2: Tensile test method using thick adherends |
|
Withdrawn |
2001-12 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
83.180
Adhesives
|
| ISO 11003-2:2019 |
Adhesives — Determination of shear behaviour of structural adhesives — Part 2: Tensile test method using thick adherends |
This document specifies a test method for determining the shear behaviour of an adhesive in a single lap joint bonded assembly when subjected to a tensile force.
The test is performed on specimens consisting of thick, rigid adherends, with a short length of overlap, in order to obtain the most uniform distribution of shear stresses possible and to minimize other stress states which initiate failure.
This test method may be used to determine:
— the shear-stress against shear-strain curve to failure of the adhesive;
— the shear modulus of the adhesive;
— other adhesive properties that can be derived from the stress/strain curve such as secant shear modulus and maximum shear stress;
— the effect of temperature, environment, test speed, etc., on these properties.
This document does not apply in case of adhesion failure.
|
Published |
2019-06 |
Edition : 3 |
Number of pages : 14 |
Technical Committee |
83.180
Adhesives
|
| ISO 11339:1993 |
Adhesives — 180 degree peel test for flexible-to-flexible bonded assemblies (T-peel test) |
Specifies a test for the determination of the peel strength of an adhesive by measuring the peeling force of a T-shaped bonded assembly of two flexible adherends. The angle between the bond line und the direction of the applied force is not fixed. Adherends are separated at an approximately steady rate from an open edge of a prepared bond, so that separation occurs progressively along the bond line. The method was originally developed for use with metal adherends, but other flexible adherends may also be used.
|
Withdrawn |
1993-08 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
83.180
Adhesives
|
| ISO 14678:2005 |
Adhesives — Determination of resistance to flow (sagging) |
ISO 14678:2005 describes seven methods for the assessment of the flow characteristics of adhesives after application at room temperature and during cure, by the measurement of sagging. These methods may be used both for specifying an adhesive and for quality control purposes.
|
Published |
2005-08 |
Edition : 1 |
Number of pages : 27 |
Technical Committee |
83.180
Adhesives
|
| ISO 11339:2003 |
Adhesives — T-peel test for flexible-to-flexible bonded assemblies |
ISO 11339:2003 specifies a T-peel test for the determination of the peel strength of an adhesive by measuring the peeling force of a T-shaped bonded assembly of two flexible adherends. This test procedure does not provide design information.
NOTE This method was originally developed for use with metal adherends, but other flexible adherends may also be used.
|
Withdrawn |
2003-03 |
Edition : 2 |
Number of pages : 5 |
Technical Committee |
83.180
Adhesives
|
| ISO 11339:2010 |
Adhesives — T-peel test for flexible-to-flexible bonded assemblies |
ISO 11339:2010 specifies a T‑peel test for the determination of the peel strength of an adhesive by measuring the peeling force of a T‑shaped bonded assembly of two flexible adherends. This test procedure does not provide design information.
This method was originally developed for use with metal adherends, but other, flexible, adherends may also be used.
|
Withdrawn |
2010-02 |
Edition : 3 |
Number of pages : 6 |
Technical Committee |
83.180
Adhesives
|
| ISO 11339:2022 |
Adhesives — T-peel test for flexible-to-flexible bonded assemblies |
This document specifies a T‑peel test for the determination of the peel resistance of an adhesive by measuring the peeling force of a T‑shaped bonded assembly of two flexible adherends. This test procedure does not provide design information.
NOTE This method was originally developed for use with metal adherends but other, flexible, adherends can also be used.
|
Published |
2022-02 |
Edition : 4 |
Number of pages : 6 |
Technical Committee |
83.180
Adhesives
|
| ISO 11343:1993 |
Adhesives — Determination of dynamic resistance to cleavage of high strength adhesive bonds under impact conditions — Wedge impact method |
The method consists of the determination of the average cleavage resistance, expressed as force or energy, of the adhesive bond between two metallic adherends. The cleavage corresponds to the separation of the adherends by a wedge, moving at high speed, whose displacement is initiated by an impact. The method allows a choice of sheet metal substrate corresponding to those materials frequently used in industry, e.g. for automotive applications.
|
Withdrawn |
1993-08 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
83.180
Adhesives
|
| ISO 11343:2003 |
Adhesives — Determination of dynamic resistance to cleavage of high-strength adhesive bonds under impact conditions — Wedge impact method |
ISO 11343:2003 specifies a dynamic impact wedge method for the determination of the cleavage resistance under impact loading of high-strength adhesive bonds between two metallic adherends, when tested under specified conditions of preparation and testing. This test procedure does not provide design information.
The method allows a choice of sheet metal substrate corresponding to those materials frequently used in industry, e.g. for automotive applications.
|
Withdrawn |
2003-04 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
83.180
Adhesives
|
| ISO 11343:2019 |
Adhesives — Determination of dynamic resistance to cleavage of high-strength adhesive bonds under impact wedge conditions — Wedge impact method |
This document specifies a dynamic impact wedge method for the determination of the cleavage resistance under impact loading of high-strength adhesive bonds between two adherends, when tested under specified conditions of preparation and testing. This test procedure does not provide design information.
The method allows a choice of sheet metal or fibre reinforced plastic substrates corresponding to those materials frequently used in industry, such as for automotive applications.
|
Published |
2019-06 |
Edition : 3 |
Number of pages : 11 |
Technical Committee |
83.180
Adhesives
|
| ISO 13007-1:2004 |
Ceramic tiles — Grouts and adhesives — Part 1: Terms, definitions and specifications for adhesives |
ISO 13007-1:2004 applies to ceramic tile adhesives for internal and external tile installations on walls and floors.
ISO 13007-1:2004 gives the terminology, concerning the products, working methods, application properties, etc., for ceramic tile adhesives.
ISO 13007-1:2004 specifies the values of performance requirements for all ceramic tile adhesives [cementitious (C), dispersion (D) and reaction resin (R) adhesives].
ISO 13007-1:2004 does not contain criteria or recommendations for the design and installation of ceramic tiles.
|
Withdrawn |
2004-12 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
83.180
Adhesives
;
91.100.23
Ceramic tiles
|
| ISO 13007-1:2004/Cor 1:2006 |
Ceramic tiles — Grouts and adhesives — Part 1: Terms, definitions and specifications for adhesives — Technical Corrigendum 1 |
|
Withdrawn |
2006-01 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
83.180
Adhesives
;
91.100.23
Ceramic tiles
|