| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO/TS 17958:2013 |
Paper and board — Determination of fracture toughness — Constant rate of elongation method (1,7 mm/s) |
ISO/TS 17958:2013 describes a method for determining the fracture toughness of paper and board using a tensile testing machine operated with a constant rate of elongation. ISO/TS 17958:2013 also describes the determination of the fracture strength and fracture strain of a notched paper web with an assigned standard web geometry. This information is used to rank the fracture properties of paper materials.
ISO/TS 17958:2013 is applicable to all kinds of paper and paperboard, except for certain special grades, such as creped paper and other paper materials that significantly deviate from exhibiting monotonically decreasing tangential stiffness during tensile testing. ISO/TS 17958:2013 does not apply to corrugated fibreboard.
|
Published |
2013-04 |
Edition : 1 |
Number of pages : 16 |
Technical Committee |
85.060
Paper and board
|
| ISO 18522:2016 |
Paper and board — Automated off-line testing of physical properties for CD (cross direction) profiles |
ISO 18522:2016 specifies the procedures for determining the cross direction profiles of physical properties of paper and board using automated off-line testers. Where available for a given measurement, the relevant International Standard is referred to. It is applicable to most kinds of paper and board, but is not relevant for tissue and corrugated board.
In ISO 18522:2016, it is left to the paper and board producer and the customer to agree upon which properties are relevant. The results are reported as mean values or as profiles across the machine. Some properties are reported in index form.
The result obtained using the relevant ISO standard based on stand-alone equipment is used in case of challenge or dispute, if not otherwise agreed.
|
Published |
2016-11 |
Edition : 1 |
Number of pages : 27 |
Technical Committee |
85.060
Paper and board
|
| ISO/TS 19857:2021 |
Paper, board and printing inks – Printability – Laboratory test method for offset ink setting |
This document describes a laboratory test method, using an IGT1-type or a prüfbau2-type printability tester, for the preparation of specimens to evaluate the absorption rate of an ink on a substrate in offset lithography by setting-off the printed surface to an unprinted surface.
This method describes testing with an amount of ink simulating either single colour or multi-colour printing. The print and the set-off print (counter print) are made with interval times, between print and set-off, common for the target process.
This method evaluates a particular ink and substrate combination.
1These materials are available from IGT Testing Systems, www.igt.nl. This information is given for the convenience of the users of this document and does not constitute an endorsement by ISO of the products. Equivalent products may be used if they can be shown to lead to the same results.
2These materials are available from prüfbau, Dr.-Ing. H. Dürner GmbH, www.pruefbau.de. This information is given for the convenience of the users of this document and does not constitute an endorsement by ISO of the products. Equivalent products may be used if they can be shown to lead to the same results.
|
Published |
2021-06 |
Edition : 1 |
Number of pages : 22 |
Technical Committee |
85.060
Paper and board
;
87.080
Inks. Printing inks
;
37.100.20
Materials for graphic technology
|
| ISO/TS 20460:2015 |
Paper and board — Automated on-line testing — Metrological comparability between standardized measurements and output of on-line gauges |
ISO/TS 20460:2015 establishes guidelines to link and, where applicable, calibrate the online gauge, following laboratory measurement for a given paper and board property.
Paper and board online measuring equipment is mostly based on different technology to that of laboratory equipment. Therefore, this Technical Specification specifies the International Standards to be chosen for the determination of physical properties of paper and board when measured online. It is applicable to all kind of paper and board.
In case of dispute, the usual reference is the laboratory testing but the parties may decide that the online measurements are valid based on the application of this International Standard.
|
Published |
2015-11 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
85.060
Paper and board
|
| ISO 20494:2017 |
Paper — Requirements for stability for general graphic applications |
ISO 20494:2017 specifies the requirements for the stability of paper for general graphic applications. It is applicable to all types of uncoated, coated and filled papers.
NOTE For information on International Standards on paper permanence (see ISO 9706), archival paper permanence and durability (see ISO 11108) and on paper stability for general graphic applications (see ISO 20494), refer to Annex C.
|
Published |
2017-12 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
85.060
Paper and board
|
| ISO 21993:2020 |
Paper and pulp — Deinkability test for printed paper products |
This document specifies a basic laboratory test method for deinkability, applicable to any kind of printed paper product, under alkaline conditions by means of single stage flotation deinking and fatty acid-based collector chemistry.
|
Published |
2020-01 |
Edition : 1 |
Number of pages : 23 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
;
85.080.01
Paper products in general
|
| ISO 22414:2004 |
Paper — Cut-size office paper — Measurement of edge quality |
ISO 22414:2004 specifies a test method for assessing the quality of the cut edge of cut-size office paper. It is applicable to papers of the type described in ISO 216, as well as other cut-size office papers used for printing and copying.
|
Published |
2004-10 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
85.060
Paper and board
;
85.080.10
Office paper
|
| ISO 22754:2008 |
Pulp and paper — Determination of the effective residual ink concentration (ERIC number) by infrared reflectance measurement |
ISO 22754:2008 specifies a method for the determination of the effective residual ink concentration (ERIC number) by infrared reflectance measurement.
ISO 22754:2008 is applicable to all types of deinked, recycled pulp and to sheets of machine-made paper made from recycled pulp, where the residual ink is black. The method is applicable to materials available in sheet form only if the opacity at 950 nm is less than 97 %. The ERIC number obtained is dependent on the distribution of ink particle sizes, and the method is most effective for submicron particles. The value obtained is reliable only if the test material is uniform in ink distribution, formation, and grammage such that presenting different parts of the sheet to the measuring aperture of the reflectometer produces very similar readings.
|
Published |
2008-11 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 22891:2007 |
Paper — Determination of transmittance by diffuse reflectance measurement |
ISO 22891:2007 specifies a method for the calculation of transmittance based upon diffuse reflectance measurements.
The use of the method is restricted to white and near-white translucent papers. If it is necessary to determine the transmittance of papers which contain fluorescent whitening agents, the fluorescence emission is eliminated using the prescribed UV cut-off filter.
|
Withdrawn |
2007-07 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
85.060
Paper and board
|
| ISO 22891:2013 |
Paper — Determination of transmittance by diffuse reflectance measurement |
ISO 22891:2013 specifies a method for the calculation of transmittance based upon diffuse reflectance measurements.
The use of the method is restricted to white and near-white translucent papers (see 3.9). If it is necessary to determine the transmittance of papers which contain fluorescent whitening agents, the fluorescence emission is eliminated using the prescribed UV cut-off filter.
|
Published |
2013-03 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
85.060
Paper and board
|
| ISO 23404:2020 |
Information and documentation — Papers and boards used for conservation — Measurement of impact of volatiles on cellulose in paper |
This document describes a test method for conservation materials which can evaluate their impact on cellulose as the main constituent of paper-based collections caused by emission of their volatile compounds.
NOTE This test can be extended to museum artefacts.
This document is applicable to papers and boards used for conservation and storage of cellulose based items.
It is not applicable to parchment-based items.
It does not evaluate the effects due to direct contact between the papers and boards used for conservation and the collections.
|
Published |
2020-08 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
85.060
Paper and board
;
01.140.20
Information sciences
|
| ISO/TS 23885:2022 |
Paper, board and graphic technology — Determination of the coating strength in the inner fold |
This document specifies a test method for the evaluation of the paper coating strength in the inner fold. The test method is intended for single or multiple coated papers up to a thickness of 150 µm that can be folded without creasing.
|
Published |
2022-06 |
Edition : 1 |
Number of pages : 16 |
Technical Committee |
85.060
Paper and board
;
37.100.01
Graphic technology in general
|
| ISO/DIS 24118-1.3 |
Paper and board — Stylus contact method — Part 1: Determination of surface roughness |
|
Under development |
|
Edition : 1 |
Number of pages : 10 |
Technical Committee |
85.060
Paper and board
|
| ISO/TS 24498:2022 |
Paper, board and pulps — Estimation of uncertainty for test methods by interlaboratory comparisons |
This document presents guidelines for a methodology for the estimation of the uncertainty of methods for testing lignins and kraft liquors, pulps, paper, board, cellulosic nanomaterials, as well as products thereof containing any portion of recycled material or material intended for recycling.
|
Published |
2022-01 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO/TR 24498:2006 |
Paper, board and pulps — Estimation of uncertainty for test methods |
ISO/TR 24498:2006 presents guidelines for the selection of the best method for the estimation of the precision of methods for testing pulp, paper and board.
|
Withdrawn |
2006-10 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 3244:1974 |
Office machines and data processing equipment — Principles governing the positioning of control keys on keyboards |
|
Withdrawn |
1974-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
35.180
IT terminal and other peripheral equipment
;
35.260
Office machines
|
| ISO/TR 24498:2019 |
Paper, board and pulps — Estimation of uncertainty for test methods by interlaboratory comparisons |
This document presents guidelines for a methodology for the estimation of the uncertainty of methods for testing pulps, paper, board, cellulosic nanomaterials, and lignins, as well as products thereof containing any portion of recycled material or material intended for recycling.
|
Withdrawn |
2019-01 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO/TR 25477:2008 |
Paper, board and pulps - Basic guidelines for image analysis measurements |
ISO/TR 25477:2008 provides guidance on using image analysis to measure various visual properties of pulp, paper, board and the corresponding products that have been printed or coated.
|
Published |
2008-09 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 328:1974 |
Picture postcards and lettercards — Size |
Does not apply to illustrated lettercards. Picture postcards and lettercards shall be size A6.
|
Withdrawn |
1974-06 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
85.080
Paper products
|
| ISO/R 499:1966 |
Paper — Internal diameters of cores of reels |
|
Withdrawn |
1966-09 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
85.080
Paper products
|
| ISO 1090:1981 |
Office machines and data processing equipment — Function key symbols on typewriters |
|
Withdrawn |
1981-01 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
35.260
Office machines
|
| ISO 1091:1977 |
Typewriters — Layout of printing and function keys |
|
Withdrawn |
1977-08 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
35.260
Office machines
|
| ISO 1092-1:1974 |
Adding machines and calculating machines — Numeric section of ten-key keyboards |
|
Withdrawn |
1974-05 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
35.160
Microprocessor systems
;
35.180
IT terminal and other peripheral equipment
;
35.260
Office machines
|
| ISO/R 1094:1969 |
Withdrawal of ISO/R 1094-1969 |
|
Withdrawn |
1969-12 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
35.260
Office machines
|
| ISO 1730:1980 |
Dictation equipment — Basic operating requirements |
Applies to dictation machines, transcription machines and to combined dictation and transcription machines. Serves to define role of these machines and to describe elements to ensure their effective operation and to specify operating requirements. References: ISO 4062; 5138/1.
|
Published |
1980-05 |
Edition : 2 |
Number of pages : 5 |
Technical Committee |
35.260
Office machines
|
| ISO/R 1731:1971 |
Withdrawal of ISO/R 1731-1971 |
|
Withdrawn |
1971-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
35.260
Office machines
|
| ISO 2126:1975 |
Office machines — Basic arrangement for the alphanumeric section of keyboards operated with both hands |
|
Withdrawn |
1975-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
35.260
Office machines
|
| ISO 2257:1980 |
Office machines and printing machines used for information processing — Widths of fabric printing ribbons on spools |
Describes the principal widths to be retained for fabric printing ribbons, also for two-coloured ones, of 19 mm (0,75 in) width and less, on spools, intended for office machines and printing machines used for information processing.
|
Published |
1980-10 |
Edition : 2 |
Number of pages : 1 |
Technical Committee |
35.260
Office machines
|
| ISO 2258:1976 |
Printing ribbons — Minimum markings to appear on containers |
Lays down rules for facilitating the storage and distribution of printing ribbons on the premises of manufacterers, dealers and users. Specifies the type and form of minimum information to appear on containers used as packaging unit for printing ribbons wound on spools or cores.
|
Published |
1976-08 |
Edition : 2 |
Number of pages : 1 |
Technical Committee |
35.260
Office machines
|
| ISO 2775:1977 |
Office machines and printing machines used for information processing — Widths of one-time paper or plastic printing ribbons and marking to indicate the end of the ribbons |
Includes the principal widths to be retained for narrow one-time paper or plastic printing ribbons (19 mm width and less) intended for office machines and printing machines used for information processing. Also defines the location of the marking indicating the approach of the end of the ribbons for office machines. Reference: ISO 2257.
|
Published |
1977-02 |
Edition : 2 |
Number of pages : 1 |
Technical Committee |
35.260
Office machines
|
| ISO 2834:1999 |
Graphic technology — Test print preparation for offset and letterpress inks |
|
Withdrawn |
1999-10 |
Edition : 3 |
Number of pages : 7 |
Technical Committee |
87.080
Inks. Printing inks
|
| ISO 3540:1976 |
Paper or plastic printing ribbons — Characteristics of cores |
Provides the most important characteristics of cores which are used to carry paper or plastic open spools printing ribbons of a nominal width of 8 mm intended for office machines and printing machines in information processing.
|
Published |
1976-06 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
35.260
Office machines
|
| ISO 3791:1976 |
Office machines and data processing equipment — Keyboard layouts for numeric applications |
Includes the basic arrangement of figures and symboles on keyboards intended for applications in which the data is mostly numeric. Reference: ISO 1092.
|
Published |
1976-08 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
35.180
IT terminal and other peripheral equipment
;
35.260
Office machines
|
| ISO 3866:1977 |
Office machines and printing machines used for information processing — Widths of fabric printing ribbons on spools exceeding 19 mm |
Includes the principal widths to be retained for fabric printing ribbons wider than 19 mm on spolls intended for office machines and machines used for information processing. Complements ISO 2257.
|
Published |
1977-06 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
35.260
Office machines
|
| ISO 3883:1977 |
Office machines — Line and character capacity of address masters |
Identifies the minimum line and character capacity of address masters as a first attempt to work towards the rationalization of the existing capacity of address masters.
|
Published |
1977-06 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
35.260
Office machines
|
| ISO 4062:1977 |
Dictation equipment — Symbols |
Includes symbols to be displayed on dictation equipment where they are used for the marking of controls and certain other parts of the devides.
|
Withdrawn |
1977-11 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
35.260
Office machines
;
01.080.20
Graphical symbols for use on specific equipment
|
| ISO 4169:1979 |
Office machines — Keyboards — Key numbering system and layout charts |
|
Withdrawn |
1979-12 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
35.180
IT terminal and other peripheral equipment
;
35.260
Office machines
|
| ISO 4232-3:1984 |
Office machines — Minimum information to be included in specification sheets — Part 3: Postal franking machines |
Contains the minimum information to be included in the specification sheets of postal franking machines so that users may compare directly the characteristics of different machines.
|
Withdrawn |
1984-07 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
35.260
Office machines
|
| ISO 4882:1979 |
Office machines and data processing equipment — Line spacings and character spacings |
Includes preferred line spacings and character spacings for office machines and data processing equipment. Is intended to provide compatibility between forms and the machines used for their completion regarding line spacings and character spacings by giving guidance to machine manufacturers and forms designers on the preferred spacings to be used.
|
Published |
1979-07 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
35.180
IT terminal and other peripheral equipment
;
35.260
Office machines
|
| ISO 5138-1:1978 |
Office machines — Vocabulary — Part 1: Dictation equipment |
Included bilingual vocabulary serves for facilitating international communication in the field of office machines. Establishes reference between entries. Covers vocabulary of dictation machines.
|
Withdrawn |
1978-12 |
Edition : 1 |
Number of pages : 20 |
Technical Committee |
35.260
Office machines
;
01.040.35
Information technology (Vocabularies)
|
| ISO 5138-3:1981 |
Office machines — Vocabulary — Part 3: Addressing machines |
Presented bilingual vocabulary is intended to facilitate international communication in the field of office machines. Establishes reference between entries. Covers vocabulary of addressing machines.
|
Withdrawn |
1981-07 |
Edition : 1 |
Number of pages : 24 |
Technical Committee |
35.260
Office machines
;
01.040.35
Information technology (Vocabularies)
|
| ISO 5138-4:1981 |
Office machines — Vocabulary — Part 4: Letter opening machines |
Included bilingual vocabulary serves for facilitating international communication in the field of office machines. Establishes references between entries. Covers vacabulary of letter opening machines.
|
Withdrawn |
1981-04 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
35.260
Office machines
;
01.040.35
Information technology (Vocabularies)
|
| ISO 12944-3:1998 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 3: Design considerations |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 5138-5:1981 |
Office machines — Vocabulary — Part 5: Letter folding machines |
Outlines terms used for letter folding machines, their main functions and types, in order to facilitate international exchange. Contains bilingual (English, French) collection of words and definitions and indicates references between them.
|
Withdrawn |
1981-04 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
35.260
Office machines
;
01.040.35
Information technology (Vocabularies)
|
| ISO 5138-7:1986 |
Office machines — Vocabulary — Part 7: Postal franking machines |
Outlines terms used for postal franking machines, their main functions and types, in order to facilitate international exchange. Contains bilingual (English, French) collection of words and definitions and indicates references between them.
|
Withdrawn |
1986-12 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
35.260
Office machines
;
01.040.35
Information technology (Vocabularies)
|
| ISO 5138-9:1984 |
Office machines — Vocabulary — Part 9: Typewriters |
Is aimed at simplifying international communication in the field of office machines. Provides English and French terms and definitions of selected concepts and establishes connections between entries. Deals with their operating processes, types, functions and parts.
|
Withdrawn |
1984-08 |
Edition : 1 |
Number of pages : 32 |
Technical Committee |
35.260
Office machines
;
01.040.35
Information technology (Vocabularies)
|
| ISO/IEC 10779:2008 |
Information technology — Office equipment accessibility guidelines for elderly persons and persons with disabilities |
ISO/IEC 10779:2008 specifies accessibility guidelines to be considered when planning, developing and designing electrophotographic copying machines, page printers and multi-function devices. These guidelines are intended to improve accessibility required when primarily older persons, persons with disabilities and persons with temporary disabilities use office equipment.
|
Withdrawn |
2008-06 |
Edition : 1 |
Number of pages : 23 |
Technical Committee |
35.260
Office machines
;
11.180.99
Other standards related to aids for disabled and handicapped people
|
| ISO/IEC 10779:2020 |
Information technology — Office equipment — Accessibility guidelines for older persons and persons with disabilities |
This document specifies accessibility guidelines to be considered when planning, developing and designing electrophotographic copying machines, page printers and multi-function devices. These guidelines are intended to improve accessibility required when primarily older persons, persons with disabilities and persons with temporary disabilities (hereafter referred to as older persons and persons with disabilities) use office equipment.
|
Published |
2020-05 |
Edition : 2 |
Number of pages : 21 |
Technical Committee |
35.260
Office machines
;
11.180.99
Other standards related to aids for disabled and handicapped people
|
| ISO/IEC 21118:2005 |
Information to be included in specification sheets — Data projectors |
ISO/IEC 21118:2005 is applicable for information to be included in specification sheets about front projection type, fixed resolution and light valve system, and data projectors having a computer signal input port capable of projecting the image outputs from a computer, VCR or other devices.
|
Withdrawn |
2005-08 |
Edition : 1 |
Number of pages : 15 |
Technical Committee |
35.260
Office machines
|
| ISO/IEC 21118:2012 |
Information technology — Office equipment — Information to be included in specification sheets — Data projectors |
ISO/IEC 21118:2012 specifies the information to be included in the specification sheets for front projection type data projectors and the form of specification sheets. It is also applicable to data projectors that have a video signal input port as well as a computer signal input port.
It is not applicable to units for a rear screen projection or with a video input terminal alone.
|
Withdrawn |
2012-12 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
35.260
Office machines
|
| ISO/IEC 21118:2020 |
Information technology — Office equipment — Information to be included in specification sheets for data projectors |
This document specifies the information to be included in the specification sheets for front projection type data projectors and the form of specification sheets.
This document is not applicable to units for a rear screen projection.
|
Published |
2020-02 |
Edition : 3 |
Number of pages : 23 |
Technical Committee |
35.260
Office machines
|
| ISO/IEC TR 22981:2020 |
Information technology — Office equipment — Guidelines for the development of an ontology (vocabulary, components and relationships) for office equipment |
This document provides background information and guidelines for the development of an ontology for office equipment.
An example of how such a standard can be used to automate the identification of resources for colour is provided.
NOTE Often the terms vocabulary and ontology are used with the same meaning.
|
Published |
2020-06 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
35.260
Office machines
|
| ISO 8502-5:1998 |
Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 5: Measurement of chloride on steel surfaces prepared for painting (ion detection tube method) |
|
Published |
1998-02 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
25.220.10
Surface preparation
|
| ISO/IEC 24700:2005 |
Quality and performance of office equipment that contains reused components |
ISO/IEC 24700:2004 specifies product characteristics for use in an original equipment manufacturer's or authorized third party's declaration of conformity to demonstrate that a marketed product that contains reused components performs equivalent to new, meeting equivalent to new component specifications and performance criteria, and continues to meet all the safety and environmental criteria required by responsibly built products. It is relevant to marketed products whose manufacturing and recovery processes result in the reuse of components. Annex C has a description of how reuse relates to other recycling processes. ISO/IEC 24700:2004 is applicable to:
A situation in which a government requires a neutral benchmark to evaluate the quality, safety and performance of equipment that contains reused components and to demonstrate the environmental responsibility of the supplier. When regulations mandate a neutral benchmark for equipment, ISO/IEC 24700:2004 provides the benchmark for proving compliance with such regulations.A situation in which a commercial supplier requires a neutral benchmark to demonstrate and communicate the quality, safety and performance of equipment that contains reused components and to demonstrate the environmental responsibility of the supplier.Situations in which consumers require a neutral benchmark to identify or distinguish environmentally responsible products.
ISO/IEC 24700:2004 reflects the world's current approaches that yield products from many manufacturing processes including the reuse of components, with the equipment's warranties and guarantees playing an important role in market acceptance. In today's procurement processes, technical equipment definitions used by regulators must be addressed and, in that sense, ISO/IEC 24700:2004 will be useful in procurement and in the trade facilitation area, to communicate with regulators. ISO/IEC 24700:2004 specifically addresses office equipment. However, in the future it may provide valuable directions for other industries and industrial sectors.
|
Published |
2005-07 |
Edition : 2 |
Number of pages : 10 |
Technical Committee |
35.260
Office machines
|
| ISO 9177-1:1989 |
Mechanical pencils — Part 1: Classification, dimensions, performance requirements and testing |
|
Withdrawn |
1989-03 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
01.100.40
Drawing equipment
|
| ISO 9177-1:2011 |
Mechanical pencils — Part 1: Classification, dimensions, performance requirements and testing |
|
Withdrawn |
2011-11 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
01.100.40
Drawing equipment
|
| ISO 9177-1:2016 |
Mechanical pencils for technical drawings — Part 1: Classification, dimensions, performance requirements and testing |
ISO 9177-1:2016 specifies classification, dimensions, performance requirements and testing for hand-held mechanical pencils used for technical drawings.
|
Published |
2016-10 |
Edition : 3 |
Number of pages : 7 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
01.100.40
Drawing equipment
|
| ISO 9177-2:1989 |
Mechanical pencils — Part 2: Black leads — Classification and dimensions |
Two types are available, black leads in which the binding agent is an organic polymer (designated by the letter "P"), and black leads in which the binding agent is clay (designated by the letter "C"). Classification is made according to the degree of hardness. Part 1 deals with the classification, dimensions, performance requirements and testing.
|
Withdrawn |
1989-03 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
01.100.40
Drawing equipment
|
| ISO 9177-2:2022 |
Mechanical pencils for technical drawings — Part 2: Black leads — Classification and dimensions |
This document specifies a classification and dimensions for black leads used for mechanical pencils for technical drawings.
Two types of black leads are available:
— polymer leads (designated by the letter “P”);
— ceramic leads (designated by the letter “C”).
|
Published |
2022-06 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
01.100.40
Drawing equipment
|
| ISO 9177-3:1994 |
Mechanical pencils — Part 3: Black leads — Bending strengths of HB leads |
Specifies bending strengths and a test method for black leads of HB hardness degree used for mechanical pencils for technical drawings.
|
Withdrawn |
1994-07 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
01.100.40
Drawing equipment
|
| ISO 9177-3:2022 |
Mechanical pencils for technical drawings — Part 3: Black leads — Bending strengths of HB leads |
This document specifies bending strengths and a test method for black leads of HB hardness degree used for mechanical pencils for technical drawings.
|
Published |
2022-01 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
01.100.40
Drawing equipment
|
| ISO 9994:1995 |
Lighters — Safety specification |
Establishes requirements for lighters to ensure a reasonable degree of safety for normal use or reasonably foreseeable misuse of such lighters.
|
Withdrawn |
1995-12 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 9994:2002 |
Lighters — Safety specification |
|
Withdrawn |
2002-03 |
Edition : 3 |
Number of pages : 23 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 8504-2:1992 |
Preparation of steel substrates before application of paints and related products — Surface preparation methods — Part 2: Abrasive blast-cleaning |
|
Withdrawn |
1992-12 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
25.220.10
Surface preparation
|
| ISO 9994:2005 |
Lighters — Safety specification |
ISO 9994:2005 establishes requirements for lighters to ensure a reasonable degree of safety for normal use or reasonably foreseeable misuse of such lighters by users.
The safety specification given in this International Standard applies to all flame-producing products commonly known as cigarette lighters, cigar lighters and pipe lighters. It does not apply to matches, nor does it apply to other flame-producing products intended solely for igniting materials other than cigarettes, cigars, and pipes.
Lighters, being flame-producing devices, can, as do all flame sources, present a potential hazard to users. The safety specification given in this International Standard cannot eliminate all hazards, but is intended to reduce potential hazards to users.
|
Withdrawn |
2005-09 |
Edition : 4 |
Number of pages : 26 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 9994:2005/Amd 1:2008 |
Lighters — Safety specification — Amendment 1: Clarification of structural requirements |
|
Withdrawn |
2008-02 |
Edition : 4 |
Number of pages : 2 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 9994:2018 |
Lighters — Safety specifications |
This document specifies requirements for lighters to ensure a reasonable degree of safety for normal use or reasonably foreseeable misuse of such lighters by users.
This document applies to all flame-producing products commonly known as cigarette lighters, cigar lighters and pipe lighters.
It does not apply to matches and flame-producing products intended solely for igniting materials other than cigarettes, cigars, and pipes.
|
Published |
2018-12 |
Edition : 5 |
Number of pages : 27 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 11540:1993 |
Caps for writing and marking instruments intended for use by children up to 14 years of age — Safety requirements |
Specifies safety requirements for cap size, ventilated caps (vent area, air flow) and marking. Annex A describes the test for air flow. Caps which do not comply should have the instrument or its packaging labelled with a warning as to the dangers of asphyxiation from pen caps.
|
Withdrawn |
1993-08 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
97.190
Equipment for children
|
| ISO 11540:2014 |
Writing and marking instruments — Specification for caps to reduce the risk of asphyxiation |
ISO 11540:2014 specifies requirements to reduce the risk of asphyxiation from caps for writing and marking instruments. It relates to such instruments which in normal or foreseeable circumstances are likely to be used by children up to the age of 14 years.
ISO 11540:2014 is not applicable to the following: writing and marking instruments which are designed or only intended for use by adults (e.g. jewellery pens, expensive fountain pens, professional technical pens); transit caps for refills.
|
Withdrawn |
2014-03 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
97.190
Equipment for children
|
| ISO 11540:2021 |
Writing and marking instruments — Specification for caps to reduce the risk of asphyxiation |
This document specifies requirements to reduce the risk of asphyxiation from caps for writing and marking instruments. It relates to such instruments which in normal or foreseeable circumstances are likely to be used by children up to the age of 14 years.
This document is not applicable to the following:
— writing and marking instruments which are designed or only intended for use by adults, e.g. jewellery pens, expensive fountain pens, professional technical pens;
— transit caps for refills.
|
Published |
2021-08 |
Edition : 3 |
Number of pages : 7 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
97.190
Equipment for children
|
| ISO 12756:1998 |
Drawing and writing instruments — Ball point pens and roller ball pens — Vocabulary |
|
Withdrawn |
1998-04 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
01.040.01
Generalities. Terminology. Standardization. Documentation (Vocabularies)
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
;
01.100.40
Drawing equipment
|
| ISO 12756:1998/Amd 1:2011 |
Drawing and writing instruments — Ball point pens and roller ball pens — Vocabulary — Amendment 1: Viscosity of the writing fluid |
|
Withdrawn |
2011-02 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
01.040.01
Generalities. Terminology. Standardization. Documentation (Vocabularies)
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
;
01.100.40
Drawing equipment
|
| ISO/TR 8502-1:1991 |
Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 1: Field test for soluble iron corrosion products |
Describes a test method which uses indicator test strips that are sensitive to ferrous ions in order to assess the soluble iron corrosion products on surfaces abrasively blast-cleaned. Does not apply to manually cleaned steel surfaces. Annex A is for information only.
|
Withdrawn |
1991-10 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
25.220.10
Surface preparation
|
| ISO 12756:2016 |
Drawing and writing instruments — Ball point pens and roller ball pens — Vocabulary |
ISO 12756:2016 defines terms related to ball point pens and roller ball pens.
|
Published |
2016-11 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
01.040.01
Generalities. Terminology. Standardization. Documentation (Vocabularies)
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
;
01.100.40
Drawing equipment
|
| ISO 12757-1:1998 |
Ball point pens and refills — Part 1: General use |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 12757-1:2016 |
Ball point pens and refills — Part 1: General use |
ISO 12757-1:2016 establishes minimum quality requirements for ball point pens (refillable or non-refillable) and refills for general use.
Additional requirements for ball point pens for documentary use are given in ISO 12757‑2.
|
Withdrawn |
2016-11 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 12757-1:2017 |
Ball point pens and refills — Part 1: General use |
ISO 12757-1:2017 establishes minimum quality requirements for ball point pens (refillable or non-refillable) and refills for general use.
Additional requirements for ball point pens for documentary use are given in ISO 12757‑2.
|
Published |
2017-12 |
Edition : 3 |
Number of pages : 9 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 14145-1:1998 |
Roller ball pens and refills — Part 1: General use |
|
Withdrawn |
1998-04 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 14145-1:1998/Amd 1:2011 |
Roller ball pens and refills — Part 1: General use — Amendment 1: Ball diameter for tip classification |
|
Withdrawn |
2011-03 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 14145-1:2016 |
Roller ball pens and refills — Part 1: General use |
ISO 14145-1:2016 establishes minimum quality requirements for roller ball pens (refillable and non-refillable) and refills for general use.
Additional requirements for roller ball pens for documentary use are given in ISO 14145‑2.
|
Withdrawn |
2016-10 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 14145-1:2017 |
Roller ball pens and refills — Part 1: General use |
|
Published |
2017-12 |
Edition : 3 |
Number of pages : 9 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 20318-1:2019 |
Mechanical pencils and leads for general use — Classification, dimensions, quality and test methods — Part 1: Mechanical pencils |
This document specifies classification, dimensions, quality and test methods for hand-held mechanical pencilss which hold and feed out a lead, and are used for general writing. It is also applicable to multi-function pens equipped with a mechanical pencil unit. However, those pencils attached to machinery instruments such as a plotter are excluded.
|
Published |
2019-02 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
01.100.40
Drawing equipment
|
| ISO 20318-2:2019 |
Mechanical pencils and leads for general use — Classification, dimensions, quality and test methods — Part 2: Black leads |
This document specifies classification, dimensions, quality and test methods for black leads used for mechanical pencils for general writing, as specified in ISO 20318-1.
|
Published |
2019-03 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
;
01.100.40
Drawing equipment
|
| ISO 22702:2003 |
Utility lighters — General consumer-safety requirements |
ISO 22702:2003 gives a consumer-safety specification covering all flame-producing consumer products commonly known as utility lighters (also known as grill lighters, fireplace lighters, lighting rods or gas matches), and similar devices. Matches are specifically excluded from the safety specification; flame-producing products intended for igniting cigars, pipes and cigarettes are also specifically excluded from the safety specification.
|
Withdrawn |
2003-11 |
Edition : 1 |
Number of pages : 20 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 22702:2003/Amd 1:2008 |
Utility lighters — General consumer-safety requirements — Amendment 1: Clarification of requirements and addition of safety symbols |
|
Withdrawn |
2008-09 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 2834:1999/Cor 1:2003 |
Graphic technology — Test print preparation for offset and letterpress inks — Technical Corrigendum 1 |
|
Withdrawn |
2003-07 |
Edition : 3 |
Number of pages : 1 |
Technical Committee |
87.080
Inks. Printing inks
|
| ISO 22702:2018 |
Utility lighters — Safety specifications |
This document specifies requirements for utility lighters to ensure a reasonable degree of safety for normal use or reasonably foreseeable misuse of such lighters by users.
This document applies to all flame-producing consumer products commonly known as utility lighters (also known as grill lighters, fireplace lighters, lighting rods or gas matches), and similar devices.
It does not apply to matches and flame-producing products intended for igniting cigars, pipes and cigarettes.
|
Published |
2018-12 |
Edition : 2 |
Number of pages : 24 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 27668-1:2009 |
Gel ink ball pens and refills — Part 1: General use |
ISO 27668-1:2009 establishes minimum quality requirements for gel ink ball pens (refillable and non-refillable) and refills for general use.
Additional requirements for gel ink ball pens for documentary use are given in ISO 27668‑2.
|
Withdrawn |
2009-02 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 27668-1:2016 |
Gel ink ball pens and refills — Part 1: General use |
ISO 27668-1:2016 establishes minimum quality requirements for gel ink ball pens (refillable and non-refillable) and refills for general use.
Additional requirements for gel ink ball pens for documentary use are given in ISO 27668‑2.
|
Withdrawn |
2016-10 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 27668-1:2017 |
Gel ink ball pens and refills — Part 1: General use |
ISO 27668-1:2017 establishes minimum quality requirements for gel ink ball pens (refillable and non-refillable) and refills for general use.
Additional requirements for gel ink ball pens for documentary use are given in ISO 27668‑2.
|
Published |
2017-11 |
Edition : 3 |
Number of pages : 11 |
Technical Committee |
97.180
Miscellaneous domestic and commercial equipment
|
| ISO 13820:1996 |
Paper, board and corrugated fibreboard — Description and calibration of compression-testing equipment |
Specifies the essential characteristics and the principles of calibration of compression testing machines used in testing of paper, board and corrugated fibreboard.
|
Withdrawn |
1996-09 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
85.100
Equipment for the paper industry
|
| ISO 13820:2014 |
Paper, board and corrugated fibreboard — Description and calibration of compression-testing equipment |
ISO 13820:2014 specifies the essential characteristics and the principles of calibration of compression testing equipment used in the testing of paper, board, and corrugated fibreboard.
|
Withdrawn |
2014-04 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
85.100
Equipment for the paper industry
|
| ISO 13820:2021 |
Paper, board and corrugated fibreboard — Description and calibration of fixed platen compression-testing equipment |
This document specifies the essential characteristics and the principles of calibration of fixed platen compression testing equipment used in the testing of paper, board, and corrugated fibreboard.
|
Published |
2021-12 |
Edition : 3 |
Number of pages : 4 |
Technical Committee |
85.100
Equipment for the paper industry
|
| ISO 12944-1:1998 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 1: General introduction |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-1:2017 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 1: General introduction |
ISO 12944-1:2017 defines the overall scope of ISO 12944 (all parts). It gives some basic terms and definitions and a general introduction to the other parts of ISO 12944. Furthermore, it includes a general statement on health, safety and environmental protection, and guidelines for using ISO 12944 (all parts) for a given project.
|
Published |
2017-11 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-2:1998 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 2: Classification of environments |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-2:2017 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 2: Classification of environments |
ISO 12944-2:2017 deals with the classification of the principal environments to which steel structures are exposed, and the corrosivity of these environments. ISO 12944-2:2017
- defines atmospheric-corrosivity categories, based on mass loss (or thickness loss) by standard specimens, and describes typical natural atmospheric environments to which steel structures are exposed, giving advice on the estimation of the corrosivity,
- describes different categories of environment for structures immersed in water or buried in soil, and
- gives information on some special corrosion stresses that can cause a significant increase in corrosion rate or place higher demands on the performance of the protective paint system.
The corrosion stresses associated with a particular environment or corrosivity category represent one essential parameter governing the selection of protective paint systems.
|
Published |
2017-11 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-3:2017 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 3: Design considerations |
ISO 12944-3:2017 deals with the basic criteria for the design of steel structures to be coated by protective paint systems in order to avoid premature corrosion and degradation of the coating or the structure. It gives examples of appropriate and inappropriate design, indicating how problems of application, inspection and maintenance of paint systems can be avoided. Design measures which facilitate handling and transport of the steel structures are also considered.
|
Published |
2017-11 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-5:1998 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 5: Protective paint systems |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 26 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-5:2007 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 5: Protective paint systems |
ISO 12944-5:2007 describes the types of paint and paint system commonly used for corrosion protection of steel structures. It also provides guidance for the selection of paint systems available for different environments and different surface preparation grades, and the durability grade to be expected. The durability of paint systems is classified in terms of low, medium and high.
|
Withdrawn |
2007-09 |
Edition : 2 |
Number of pages : 28 |
Technical Committee |
87.020
Paint coating processes
|