| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO/CD 19967-3 |
Air to water Heat pumps — Testing and rating for performance — — Part 3: Combined hot water supply and space heating and/or space cooling |
This part of standard wants to provide a testing and rating method of performance for heat pump water heater products with the functions combined of hygienic hot water supply and space conditioning by cooling or heating water.
|
Under development |
|
Edition : 1 |
|
Technical Committee |
27.080
Heat pumps
|
| ISO 14903:2017 |
Refrigerating systems and heat pumps — Qualification of tightness of components and joints |
ISO 14903:2017 provides the qualification procedure for type approval of the tightness of hermetically sealed and closed components, joints and parts used in refrigerating systems and heat pumps as described in relevant parts of ISO 5149. The sealed and closed components, joints and parts concerned are, in particular, fittings, bursting discs, flanged or fitted assemblies. The tightness of flexible piping made from non-metallic materials is dealt with in ISO 13971. Metal flexible piping are covered by this document.
The requirements contained in this document are applicable to joints of maximum DN 50 and components of internal volume of maximum 5 l and maximum weight of 50 kg.
ISO 14903:2017 is intended to characterize their tightness stresses met during their operations, following the fitting procedure specified by the manufacturer, and to specify the minimal list of necessary information to be provided by the supplier of a component to the person in charge of carrying out this procedure.
It specifies the level of tightness of the component, as a whole, and its assembly as specified by its manufacturer.
It applies to the hermetically sealed and closed components, joints and parts used in the refrigerating installations, including those with seals, whatever their material and their design are.
ISO 14903:2017 specifies additional requirements for mechanical joints that can be recognized as hermetically sealed joints.
|
Published |
2017-07 |
Edition : 2 |
Number of pages : 34 |
Technical Committee |
27.080
Heat pumps
;
27.200
Refrigerating technology
|
| ISO 14903:2017/FDAmd 1 |
Refrigerating systems and heat pumps — Qualification of tightness of components and joints — Amendment 1 |
|
Deleted |
|
Edition : 2 |
|
Technical Committee |
27.080
Heat pumps
;
27.200
Refrigerating technology
|
| ISO/DIS 14903 |
Refrigerating systems and heat pumps — Qualification of tightness of components and joints |
ISO 14903:2017 provides the qualification procedure for type approval of the tightness of hermetically sealed and closed components, joints and parts used in refrigerating systems and heat pumps as described in relevant parts of ISO 5149. The sealed and closed components, joints and parts concerned are, in particular, fittings, bursting discs, flanged or fitted assemblies. The tightness of flexible piping made from non-metallic materials is dealt with in ISO 13971. Metal flexible piping are covered by this document.
The requirements contained in this document are applicable to joints of maximum DN 50 and components of internal volume of maximum 5 l and maximum weight of 50 kg.
ISO 14903:2017 is intended to characterize their tightness stresses met during their operations, following the fitting procedure specified by the manufacturer, and to specify the minimal list of necessary information to be provided by the supplier of a component to the person in charge of carrying out this procedure.
It specifies the level of tightness of the component, as a whole, and its assembly as specified by its manufacturer.
It applies to the hermetically sealed and closed components, joints and parts used in the refrigerating installations, including those with seals, whatever their material and their design are.
ISO 14903:2017 specifies additional requirements for mechanical joints that can be recognized as hermetically sealed joints.
|
Under development |
|
Edition : 3 |
|
Technical Committee |
27.080
Heat pumps
;
27.200
Refrigerating technology
|
| ISO 15042:2011 |
Multiple split-system air-conditioners and air-to-air heat pumps — Testing and rating for performance |
ISO 15042:2011 establishes performance testing and rating criteria for factory-made residential, commercial and industrial, electrically-driven, mechanical-compression, air-cooled air-conditioners and air-to-air heat pumps, described as basic multi-split systems, modular multi-split systems and modular heat recovery multi-split systems. These multi-split systems include air-to-air systems with non-ducted and/or ducted indoor units with integral fans and indoor units supplied without fans.
ISO 15042:2011 is limited to single and multiple circuit split-systems which utilize one or more compressors with no more than two steps of control of the outdoor unit. It is also limited to split-systems with a single refrigeration circuit which utilize one or more variable-speed compressors or alternative compressor combinations for varying the capacity of the system by three or more steps. These split-systems are designed to operate with a combination of one or more outdoor units and two or more indoor units designed for individual operation, and such modular systems that are capable of transferring recovered heat from one or more indoor units to other units in the same system.
|
Withdrawn |
2011-11 |
Edition : 1 |
Number of pages : 94 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 15042:2017 |
Multiple split-system air conditioners and air-to-air heat pumps — Testing and rating for performance |
ISO 15042:2017 specifies the performance testing, the standard conditions and the test methods for determining the capacity and efficiency ratings of air-cooled air conditioners and air-to-air heat pumps.
ISO 15042:2017 is applicable to the following equipment:
-― basic multi-split systems, modular multi-split systems and modular heat recovery multi-split systems. These multi-split systems include air-to-air systems with non-ducted and/or ducted indoor units with integral fans and indoor units supplied without fans.
ISO 15042:2017 is limited to:
- residential, commercial and industrial split-system air conditioners and heat pumps;
- factory-made, electrically driven and use mechanical compression;
- single- and multiple-circuit split-systems which utilize one or more compressors with no more than two steps of control of the outdoor unit;
or
- split-systems with a single refrigeration circuit which utilize one or more variable-speed compressors or alternative compressor combinations for varying the capacity of the system by three or more steps.
These split-systems are designed to operate with a combination of one or more outdoor units and two or more indoor units designed for individual operation, and such modular systems are capable of transferring recovered heat from one or more indoor units to other units in the same system.
The requirements of testing and rating contained in this document are based on the use of matched assemblies.
ISO 15042:2017 is not applicable to the rating and testing of the following:
a) water-cooled or water source equipment;
b) mobile (single-duct) units having a condenser exhaust duct;
c) individual assemblies not constituting a complete refrigeration system;
d) equipment using the absorption refrigeration cycle.
e) ducted air conditioners and/or ducted heat pumps, rated at less than 8 kW and intended to operate at external static pressures of less than 25 Pa, controlled by a single thermostat/controller (refer to ISO 5151);
f) multiple split-system utilizing one or more refrigeration systems, one outdoor unit and one or more indoor units, controlled by a single thermostat/controller (refer to ISO 5151 or ISO 13253).
ISO 15042:2017 does not cover the determination of seasonal efficiencies or seasonal part-load performances, which can be required in some countries because they provide a better indication of efficiency under actual operating conditions.
NOTE Throughout this document, the terms "equipment" and "systems" mean "multi-split air conditioners" and/or "multi-split heat pumps".
|
Published |
2017-07 |
Edition : 2 |
Number of pages : 97 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16358-1:2013 |
Air-cooled air conditioners and air-to-air heat pumps — Testing and calculating methods for seasonal performance factors — Part 1: Cooling seasonal performance factor |
ISO 16358-1:2013 specifies the testing and calculating methods for seasonal performance factor of equipment covered by ISO 5151, ISO 13253 and ISO 15042.
ISO 16358-1:2013 also specifies the seasonal performance test conditions and the corresponding test procedures for determining the seasonal performance factor of equipment, as specified above, under mandatory test conditions and is intended for use only in marking, comparison, and certification purposes. For the purposes of ISO 16358-1:2013, the rating conditions are those specified under T1 in the reference standards above. The procedures in ISO 16358-1:2013 may be used for other temperature conditions.
ISO 16358-1:2013 does not apply to the testing and rating of:
water-source heat pumps or water-cooled air conditioners;
portable units having a condenser exhaust duct;
individual assemblies not constituting a complete refrigeration system; or
equipment using the absorption refrigeration cycle.
|
Published |
2013-04 |
Edition : 1 |
Number of pages : 26 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16358-1:2013/Amd 1:2019 |
Air-cooled air conditioners and air-to-air heat pumps — Testing and calculating methods for seasonal performance factors — Part 1: Cooling seasonal performance factor — Amendment 1 |
|
Published |
2019-04 |
Edition : 1 |
Number of pages : 21 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16358-1:2013/Cor 1:2013 |
Air-cooled air conditioners and air-to-air heat pumps — Testing and calculating methods for seasonal performance factors — Part 1: Cooling seasonal performance factor — Technical Corrigendum 1 |
|
Published |
2013-11 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16358-2:2013 |
Air-cooled air conditioners and air-to-air heat pumps — Testing and calculating methods for seasonal performance factors — Part 2: Heating seasonal performance factor |
ISO 16358-2:2013 specifies the testing and calculating methods for seasonal performance factor of equipment covered by ISO 5151, ISO 13253 and ISO 15042. For the purposes of ISO 16358-2:2013, it is assumed that any make-up heating will be provided by electric heaters running concurrently with the heat pump.
ISO 16358-2:2013 also specifies the seasonal performance test conditions and the corresponding test procedures for determining the seasonal performance factor of equipment, as specified above, under mandatory test conditions and is intended for use only in marking, comparison, and certification purposes.
ISO 16358-2:2013 does not apply to the testing and rating of:
water-source heat pumps or water-cooled air conditioners;
portable units having a condenser exhaust duct;
individual assemblies not constituting a complete refrigeration system; or
equipment using the absorption refrigeration cycle.
|
Published |
2013-04 |
Edition : 1 |
Number of pages : 38 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16358-2:2013/Cor 1:2013 |
Air-cooled air conditioners and air-to-air heat pumps — Testing and calculating methods for seasonal performance factors — Part 2: Heating seasonal performance factor — Technical Corrigendum 1 |
|
Published |
2013-11 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16358-3:2013 |
Air-cooled air conditioners and air-to-air heat pumps — Testing and calculating methods for seasonal performance factors — Part 3: Annual performance factor |
ISO 16358-3:2013 specifies the testing and calculating methods for seasonal performance factor of equipment covered by ISO 5151, ISO 13253 and ISO 15042.
ISO 16358-3:2013 also specifies the seasonal performance test conditions and the corresponding test procedures for determining the seasonal performance factor of equipment, as specified above, under mandatory test conditions and is intended for use only in marking, comparison, and certification purposes.
ISO 16358-3:2013 does not apply to the testing and rating of:
water-source heat pumps or water-cooled air conditioners;
portable units having a condenser exhaust duct;
individual assemblies not constituting a complete refrigeration system; or
equipment using the absorption refrigeration cycle.
|
Published |
2013-04 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO/TS 16491:2012 |
Guidelines for the evaluation of uncertainty of measurement in air conditioner and heat pump cooling and heating capacity tests |
ISO/TS 16491:2012 gives guidance on the practical applications of the principles of performance measurement of air-cooled air-conditioners and air-to-air heat pumps as described in ISO 5151, ISO 13253, and ISO 15042.
|
Published |
2012-12 |
Edition : 1 |
Number of pages : 28 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO/DIS 24664 |
Refrigerating systems and heat pumps — Pressure relief devices and their associated piping — Methods for calculation |
|
Under development |
|
Edition : 1 |
Number of pages : 31 |
Technical Committee |
27.080
Heat pumps
;
27.200
Refrigerating technology
|
| ISO 16494-1:2022 |
Heat recovery ventilators and energy recovery ventilators — Method of test for performance — Part 1: Development of metrics for evaluation of energy related performance |
This document specifies a method of testing the ventilation and energy related performance of heat recovery ventilators (HRVs) and energy recovery ventilators (ERVs) that do not contain any supplemental heating (except for defrost), cooling, humidification, or dehumidification components.
Exchanger types of HRVs and ERVs are
a) fixed-plate exchangers (also known as recuperators),
b) rotary exchangers, including heat wheels and total energy wheels (also known as regenerators), and
c) heat pipe exchangers using a heat transfer medium, excluding those using mechanical pumping,
This document does not provide a method for measuring the response of exchangers to the formation of frost.
|
Published |
2022-06 |
Edition : 1 |
Number of pages : 40 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16494-1:2022/DAmd 1 |
Heat recovery ventilators and energy recovery ventilators — Method of test for performance — Part 1: Development of metrics for evaluation of energy related performance — Amendment 1 |
|
Under development |
|
Edition : 1 |
Number of pages : 9 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16494:2014 |
Heat recovery ventilators and energy recovery ventilators — Method of test for performance |
ISO 16494:2014 prescribes a method of testing the ventilation and energy related performance of heat recovery ventilators (HRVs)and energy recovery ventilators (ERVs) that do not contain any supplemental heating (except for defrost), cooling, humidification or dehumidification components.
|
Withdrawn |
2014-11 |
Edition : 1 |
Number of pages : 38 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 18326:2018 |
Non-ducted portable air-cooled air conditioners and air-to-air heat pumps having a single exhaust duct — Testing and rating for performance |
This document specifies the standard conditions for capacity and efficiency ratings of non-ducted portable air-cooled air conditioners having a single exhaust duct and non-ducted portable air-cooled heat pumps having a single exhaust duct. Such air conditioners and heat pumps may include an evaporatively cooled condenser cooled by air and the evaporation of:
a) condensate collected from the evaporator;
b) external supplementary water stored in a supplementary water tank; or
c) both a) and b).
This document also specifies the test methods for determining the capacity and efficiency ratings.
This document applies to equipment that is factory-made, electrically driven and uses mechanical compression. This document is applicable to equipment utilizing one or more refrigeration systems.
This document is not applicable to the rating and testing of the following:
i) Water-source heat pumps or water-cooled air conditioners;
ii) Multi-split-system air conditioners and air-to-air heat pumps (see ISO 15042:2017 for the testing of such equipment);
iii) Individual assemblies not constituting a complete refrigeration system;
iv) Equipment using the absorption refrigeration cycle;
v) Ducted equipment (see ISO 13253:2017 for the testing of such equipment);
vi) Evaporative coolers or any other cooling systems that are not of the vapour compression type;
vii) Dehumidifiers;
viii) Spot coolers.
|
Published |
2018-09 |
Edition : 1 |
Number of pages : 47 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 18326:2018/Amd 1:2021 |
Non-ducted portable air-cooled air conditioners and air-to-air heat pumps having a single exhaust duct — Testing and rating for performance — Amendment 1 |
|
Published |
2021-05 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 19967-1:2019 |
Heat pump water heaters — Testing and rating for performance — Part 1: Heat pump water heater for hot water supply |
This document specifies test conditions and test procedures for determining the performance characteristics of air source heat pump water heaters for hot water supply with electrically driven compressors with or without supplementary electric heater and connected to or including only one hot water storage tank. Hot water storage tanks that are connected in series or parallel and behave hydronically as one single tank are considered as one hot water storage tank. In the case of heat pump water heaters consisting of several parts with refrigerant or water connections, this document applies only to those designed and supplied as a complete package.
NOTE This document is not applicable to testing procedures for simultaneous operation for hot water supply and space heating. "Simultaneous" means that hot water supply and space heating generation occur at the same time and may interact.
|
Published |
2019-03 |
Edition : 1 |
Number of pages : 30 |
Technical Committee |
27.080
Heat pumps
|
| ISO 19967-2:2019 |
Heat pump water heaters — Testing and rating for performance — Part 2: Heat pump water heaters for space heating |
This document specifies test conditions and test procedures for determining the performance characteristics of air source heat pump water heaters for space heating with electrically driven compressors with or without supplementary heater. The purpose of this document is to rate the performance of the heat pump water heaters for space heating with no operation of any supplementary heater. In the case of heat pump water heaters for space heating consisting of several parts with refrigerant or water connections, this document applies only to those designed and supplied as a complete package.
NOTE Testing procedures for simultaneous operation for hot water supply and space heating are not treated in this document. Simultaneous means that hot water supply and space heating generation occur at the same time and can interact.
|
Published |
2019-06 |
Edition : 1 |
Number of pages : 25 |
Technical Committee |
27.080
Heat pumps
|
| ISO 21922:2021 |
Refrigerating systems and heat pumps — Valves — Requirements, testing and marking |
This document specifies safety requirements, certain functional requirements, and marking of valves and other components with similar bodies, hereinafter called valves, for use in refrigerating systems including heat pumps.
This document includes requirements for valves with extension pipes.
This document describes the procedure to be followed when designing valve parts subjected to pressure as well as the criteria to be used in the selection of materials.
This document describes methods by which reduced impact values at low temperatures may be taken into account in a safe manner.
This document applies to the design of bodies and bonnets for pressure relief devices, including bursting disc devices, with respect to pressure containment but it does not apply to any other aspects of the design or application of pressure relief devices.
In addition, this document is applicable to valves with a maximum operating temperature not exceeding 200 °C and a maximum allowable pressure not exceeding 160 bar[1].
[1] 1 bar = 0,1 MPa.
|
Published |
2021-08 |
Edition : 1 |
Number of pages : 90 |
Technical Committee |
27.080
Heat pumps
;
27.200
Refrigerating technology
|
| ISO 21922:2021/DAmd 1 |
Refrigerating systems and heat pumps — Valves — Requirements, testing and marking — Amendment 1 |
|
Under development |
|
Edition : 1 |
Number of pages : 7 |
Technical Committee |
27.080
Heat pumps
;
27.200
Refrigerating technology
|
| ISO 21978:2021 |
Heat pump water heater — Testing and rating at part load conditions and calculation of seasonal coefficient of performance for space heating |
The document specifies test conditions for determining the seasonal performance characteristics of air source heat pump water heaters for space heating with electrically driven compressors with or without supplementary heater. The purpose of this document is to rate performance of the heat pump water heaters for space heating with no operation of any supplementary heater. In the case of heat pump water heaters for space heating consisting of several parts with refrigerant or water connections, this document applies only to those designed and supplied as a complete package.
The seasonal coefficient of performance depends, inter alia, on the climate conditions and temperature regime of the space heating distribution network.
This document defines:
— three design conditions, each of them being characterized by a design temperature which represents the lowest temperature that can occur in that design condition;
— three water temperature distribution regimes, namely "temperature application" in the text.
The user of this document is free to determine the seasonal coefficient of performance for one or more of the defined design conditions and for one or more of the defined temperature applications.
This document also provides a full description of three heating seasons that can be used with the associated design conditions.
|
Published |
2021-02 |
Edition : 1 |
Number of pages : 47 |
Technical Committee |
27.080
Heat pumps
|
| ISO/DIS 21978 |
Air to water heat pumps — Testing and rating at part load conditions and calculation of seasonal coefficient of performance for space heating |
The document specifies test conditions for determining the seasonal performance characteristics of air source heat pump water heaters for space heating with electrically driven compressors with or without supplementary heater. The purpose of this document is to rate performance of the heat pump water heaters for space heating with no operation of any supplementary heater. In the case of heat pump water heaters for space heating consisting of several parts with refrigerant or water connections, this document applies only to those designed and supplied as a complete package.
The seasonal coefficient of performance depends, inter alia, on the climate conditions and temperature regime of the space heating distribution network.
This document defines:
— three design conditions, each of them being characterized by a design temperature which represents the lowest temperature that can occur in that design condition;
— three water temperature distribution regimes, namely "temperature application" in the text.
The user of this document is free to determine the seasonal coefficient of performance for one or more of the defined design conditions and for one or more of the defined temperature applications.
This document also provides a full description of three heating seasons that can be used with the associated design conditions.
|
Under development |
|
Edition : 2 |
Number of pages : 46 |
Technical Committee |
27.080
Heat pumps
|
| ISO 22712:2023 |
Refrigerating systems and heat pumps — Competence of personnel |
This document defines the activities related to refrigerating systems according to ISO 5149‑1, ISO 5149‑2, ISO 5149‑3 and ISO 5149‑4 and other equivalent standards, such as EN 378‑1, EN 378‑2, EN 378‑3, EN 378‑4 and the associated competence profiles. It also establishes the competence criteria for persons who carry out these activities. Activities concerning electricity are excluded.
NOTE 1 As a refrigerating circuit is considered not to incorporate electrical and electronic systems, activities in this area are not part of this document. National regulations or appropriate International or national standards can be referred to for competence on electrical and electronic systems.
NOTE 2 This document does not apply to persons carrying out work on self‑contained refrigerating systems as defined in ISO 5149‑1 or EN 378‑1, from the initial design of the product to the complete manufacture of the product, provided the process is controlled and the methods used are checked by an organization or individual responsible for the conformance with statutory requirements on health, safety and environment (e.g. energy efficiency).
NOTE 3 This document does not constitute a training programme.
|
Published |
2023-03 |
Edition : 1 |
Number of pages : 36 |
Technical Committee |
27.080
Heat pumps
;
27.200
Refrigerating technology
;
03.100.30
Management of human resources
|
| ISO 12944-1:1998 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 1: General introduction |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-1:2017 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 1: General introduction |
ISO 12944-1:2017 defines the overall scope of ISO 12944 (all parts). It gives some basic terms and definitions and a general introduction to the other parts of ISO 12944. Furthermore, it includes a general statement on health, safety and environmental protection, and guidelines for using ISO 12944 (all parts) for a given project.
|
Published |
2017-11 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-2:1998 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 2: Classification of environments |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-2:2017 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 2: Classification of environments |
ISO 12944-2:2017 deals with the classification of the principal environments to which steel structures are exposed, and the corrosivity of these environments. ISO 12944-2:2017
- defines atmospheric-corrosivity categories, based on mass loss (or thickness loss) by standard specimens, and describes typical natural atmospheric environments to which steel structures are exposed, giving advice on the estimation of the corrosivity,
- describes different categories of environment for structures immersed in water or buried in soil, and
- gives information on some special corrosion stresses that can cause a significant increase in corrosion rate or place higher demands on the performance of the protective paint system.
The corrosion stresses associated with a particular environment or corrosivity category represent one essential parameter governing the selection of protective paint systems.
|
Published |
2017-11 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-3:1998 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 3: Design considerations |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-3:2017 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 3: Design considerations |
ISO 12944-3:2017 deals with the basic criteria for the design of steel structures to be coated by protective paint systems in order to avoid premature corrosion and degradation of the coating or the structure. It gives examples of appropriate and inappropriate design, indicating how problems of application, inspection and maintenance of paint systems can be avoided. Design measures which facilitate handling and transport of the steel structures are also considered.
|
Published |
2017-11 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-5:1998 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 5: Protective paint systems |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 26 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-5:2007 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 5: Protective paint systems |
ISO 12944-5:2007 describes the types of paint and paint system commonly used for corrosion protection of steel structures. It also provides guidance for the selection of paint systems available for different environments and different surface preparation grades, and the durability grade to be expected. The durability of paint systems is classified in terms of low, medium and high.
|
Withdrawn |
2007-09 |
Edition : 2 |
Number of pages : 28 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-5:2018 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 5: Protective paint systems |
ISO 12944-5:2018 describes the types of paint and paint system commonly used for corrosion protection of steel structures.
ISO 12944-5:2018 also gives guidelines for the selection of paint systems available for different environments (see ISO 12944‑2) except for corrosivity category CX and category Im4 as defined in ISO 12944‑2 and different surface preparation grades (see ISO 12944‑4), and the durability grade to be expected (see ISO 12944‑1).
|
Withdrawn |
2018-02 |
Edition : 3 |
Number of pages : 22 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-5:2019 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 5: Protective paint systems |
This document describes the types of paint and paint system commonly used for corrosion protection of steel structures.
It also gives guidelines for the selection of paint systems available for different environments (see ISO 12944‑2) except for corrosivity category CX and category Im4 as defined in ISO 12944‑2 and different surface preparation grades (see ISO 12944‑4), and the durability grade to be expected (see ISO 12944‑1).
|
Published |
2019-09 |
Edition : 4 |
Number of pages : 23 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-6:1998 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 6: Laboratory performance test methods |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-6:2018 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 6: Laboratory performance test methods |
ISO 12944-6:2018 specifies laboratory test methods and test conditions for the assessment of paint systems for the corrosion protection of carbon steel structures.
The test results are intended to be considered as an aid in the selection of suitable paint systems and not as exact information for determining durability.
ISO 12944-6:2018 covers protective paint systems designed for application to uncoated steel, hot dip galvanized steel according to ISO 1461 and steel surfaces with thermal-sprayed metallic coating according to ISO 2063‑1 and ISO 2063‑2.
ISO 12944-6:2018 does not apply to protective paint systems for electroplated or painted steel.
The environments for corrosivity categories C2 to C5 and Im1 to Im3 defined in ISO 12944‑2 are considered.
|
Published |
2018-01 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-7:1998 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 7: Execution and supervision of paint work |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-7:2017 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 7: Execution and supervision of paint work |
ISO 12944-7:2017 deals with the execution and supervision of paint work on steel structures in the workshop or on site.
ISO 12944-7:2017 does not apply to
- the preparation of surfaces to be painted (see ISO 12944‑4) and the supervision of such work,
- the application of metallic coatings, and
- pre-treatment methods, such as phosphating and chromating, and paint application methods, such as dipping, powder coating or coil coating.
|
Published |
2017-11 |
Edition : 2 |
Number of pages : 10 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-8:1998 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 8: Development of specifications for new work and maintenance |
|
Withdrawn |
1998-05 |
Edition : 1 |
Number of pages : 39 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 12944-8:2017 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 8: Development of specifications for new work and maintenance |
ISO 12944-8:2017 covers the development of specifications for corrosion protection of steel structures using protective paint systems. It relates to new work and maintenance in the workshop or on site and is also applicable to the corrosion protection of individual components. ISO 12944-8:2017 covers the corrosion protection of steel structures exposed to different corrosion stresses by environments such as indoors, open-air and immersion in water or burial in soil, as well as special stresses, due for example, to medium or high temperatures. The need for different durability ranges is considered.
Steel surfaces that have been hot-dip-galvanized, metal-sprayed, zinc-electroplated or sherardized, and previously painted steel surfaces, are also covered by ISO 12944-8:2017.
In ISO 12944-8:2017, reference areas for assessing the quality of the corrosion protection work and the performance of the protective paint systems used are dealt with. ISO 12944-8:2017 provides detailed flow charts for planning new work and maintenance, which are taken into account when writing a specification.
ISO 12944-8:2017 can also be used as a guide if extreme corrosion stresses or high temperatures occur, or if the protective paint systems are to be used on other substrates, such as non-ferrous metals or concrete, to define suitable specifications.
|
Published |
2017-11 |
Edition : 2 |
Number of pages : 36 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 15741:2001 |
Paints and varnishes — Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases |
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 23 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 15741:2016 |
Paints and varnishes — Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases |
ISO 15741:2016 specifies requirements and methods of test for liquid epoxy paints and internal coatings of such paints in steel pipes and fittings for the conveyance of non-corrosive gas. It also deals with the application of the paint. Other paints or paint systems are not excluded provided they comply with the requirements given in ISO 15741:2016. The coating consists of one layer, which is normally shop-applied on blast-cleaned steel by airless spray or other suitable spraying techniques. The applied and cured paint film must be smooth to give the desired reduction in friction. Brush application is only used for small repair jobs.
|
Published |
2016-11 |
Edition : 2 |
Number of pages : 23 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 16276-1:2007 |
Corrosion protection of steel structures by protective paint systems — Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating — Part 1: Pull-off testing |
ISO 16276-1:2007 specifies procedures for assessing the fracture strength of a protective paint coating of any thickness on a steel substrate of thickness not less than 10 mm. The procedures given in this part of ISO 16276 are based on methods used with different types of pull-off test equipment. The results obtained using such different types of equipment are not comparable.
This part of ISO 16276 also specifies suitable equipment and defines inspection areas, sampling plans and acceptance/rejection criteria.
It does not give any values of the fracture strength of different protective paint coatings.
|
Published |
2007-05 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 16276-2:2007 |
Corrosion protection of steel structures by protective paint systems — Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating — Part 2: Cross-cut testing and X-cut testing |
ISO 16276-2:2007 specifies procedures for rating the resistance of coating systems when a cut in the form of a right-angle lattice pattern (cross-cut) or in the form of an X (X-cut) is made into the coating, penetrating through to the substrate.
It also specifies suitable equipment and defines inspection areas, sampling plans and acceptance/rejection criteria.
It does not specify ratings for particular coating systems.
|
Published |
2007-05 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 19840:2004 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Measurement of, and acceptance criteria for, the thickness of dry films on rough surfaces |
ISO 19840:2004 specifies a procedure for the verification of dry film thickness against the nominal dry film thickness on rough surfaces, including the adjustment of the instruments used, the definition of inspection areas, sampling plans, measurement methods and acceptance/rejection criteria.
The procedure is based on the use of instruments of the permanent magnet and inductive magnet type, adjusted to zero and to a known thickness on a smooth surface.
It does not apply to nominal dry film thicknesses less than 40 micrometres.
|
Withdrawn |
2004-11 |
Edition : 1 |
Number of pages : 15 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 19840:2012 |
Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Measurement of, and acceptance criteria for, the thickness of dry films on rough surfaces |
ISO 19840:2012 specifies a procedure for the verification of dry-film thickness against nominal dry-film thickness on rough surfaces, including the adjustment of the instruments used, the definition of inspection areas, sampling plans, measurement methods and acceptance/rejection criteria.
The procedure is based on the use of instruments of the permanent magnet, electromagnet and eddy current type. Instrument accuracy is verified both at zero and at a known thickness on a smooth surface and adjusted if necessary.
It does not apply to nominal dry-film thicknesses less than 40 µm.
|
Published |
2012-09 |
Edition : 2 |
Number of pages : 16 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 20340:2003 |
Paints and varnishes — Performance requirements for protective paint systems for offshore and related structures |
ISO 20340:2003 deals with the performance requirements for the protection, by protective paint systems, of new offshore and related structures exposed to the offshore atmosphere, as well as those immersed in sea or brackish water. ISO 20340 can also be used for other structures, provided that the selected paints or protective paint systems comply with this International Standard.
This International Standard places emphasis on high-durability paint systems, with the aim of minimizing maintenance, and hence reducing safety considerations and environmental impact.
This International Standard includes the following:
the test methods to be used to determine the composition of the separate components of the protective paint system;the laboratory performance test methods for the assessment of the likely durability of the protective paint system;the criteria to be used to evaluate the results of performance tests.
|
Withdrawn |
2003-11 |
Edition : 1 |
Number of pages : 23 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 29601:2011 |
Paints and varnishes — Corrosion protection by protective paint systems — Assessment of porosity in a dry film |
ISO 29601:2011 specifies procedures for detecting the presence of porosity in a protective paint system of any thickness on a steel or other metallic substrate. The procedures given are based on methods using two different types of test equipment, the choice of equipment depending on the dry film thickness. These procedures are only applicable to the testing of electrically non-conductive parts of a paint system.
The test methods specified are mainly intended for use with new coatings, but can also be used for coatings which have been in service for some time. In the latter case, it is important to bear in mind that the coating might have been penetrated by substances in contact with the coating during service.
|
Published |
2011-04 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
87.020
Paint coating processes
|
| ISO 3443-1:1979 |
Tolerances for building — Part 1: Basic principles for evaluation and specification |
Describes the nature of dimensional variability in building and the purposes for which it has to be quantified, and defines the factors to be taken into account in the evaluation, specification and verification of tolerances for the manufacture of building components and for site work. Applies to components and buildings generally, including those designed in accordance with the principles of modular co-ordination.
|
Published |
1979-06 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
91.200
Construction technology
|
| ISO 3443-2:1979 |
Tolerances for building — Part 2: Statistical basis for predicting fit between components having a normal distribution of sizes |
Describes the fundamental characteristics of dimensional variability in building and of the particular case of combination of random unrelated variables. Sets out the need to relate dimensional variability to the limits imposed on joint widths by the need for satisfactory functioning. Applies to all forms of building construction that have predictable variability which follows a Gaussian distribution.
|
Published |
1979-07 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
91.200
Construction technology
|
| ISO 4463:1979 |
Measurement methods for building — Setting out and measurement — Permissible measuring deviations |
|
Withdrawn |
1979-12 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
91.200
Construction technology
|
| ISO 3443-3:1987 |
Tolerances for building — Part 3: Procedures for selecting target size and predicting fit |
Provides a basis for relating joint clearances and target sizes and for the prediction of fit within the context of dimensional coordination, including modular coordination. Is intended for use by component manufacturers when determining target sizes for standard components and by building designers when determining target sizes for construction on site, assessing the applicability of standard components or determining target sizes for non-standard components.
|
Published |
1987-02 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
91.200
Construction technology
|
| ISO 3443-4:1986 |
Tolerances for building — Part 4: Method for predicting deviations of assemblies and for allocation of tolerances |
Indicates some general principles and a method for predicting deviations in composite systems and specifying tolerances for the constituent elements in order to meet functional requirements and tolerance specifications for the assembly. Applies to tolerances and deviations in all kind of assemblies and other systems composed of elements, within the building industry.
|
Published |
1986-12 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
91.200
Construction technology
|
| ISO 3443-5:1982 |
Building construction — Tolerances for building — Part 5: Series of values to be used for specification of tolerances |
Specifies a series of values from which tolerances shall be chosen for dimensional specification of building components and constructions. The basis for the determination of the tolerances to be specified is dealt with in other standards, especially ISO 3443 parts 1 to 4 and ISO 4464.
|
Published |
1982-12 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
91.200
Construction technology
|
| ISO 3443-6:1986 |
Tolerances for building — Part 6: General principles for approval criteria, control of conformity with dimensional tolerance specifications and statistical control — Method 1 |
Gives the general principles according to which tolerances should be specified and the approval criteria of geometrical characteristics which result from any operation made in building construction. Applies to all types of form, dimensions and positions within the building industry where tolerances are specified.
|
Published |
1986-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
91.200
Construction technology
|
| ISO 3443-7:1988 |
Tolerances for building — Part 7: General principles for approval criteria, control of conformity with dimensional tolerance specifications and statistical control — Method 2 (Statistical control method) |
Specifies an operational procedure which can be used to determine acceptance of dimensional accuracy of components, and operations in the building industry to be used when the parties involved agree to refer to this part of ISO 3443. The procedure relates to the recognition of specified requirements, the criteria of acceptance and consequences of rejection, recommendations on the agreements and methods of measurement, and the planning and execution of inspection by statistical methods. Applies to all types of forms, dimensions and positions within the building industry.
|
Published |
1988-05 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
91.200
Construction technology
|
| ISO 3443-8:1989 |
Tolerances for building — Part 8: Dimensional inspection and control of construction work |
Gives the procedures to be understood and a list of items to be agreed upon by all parties in a building project. Applies to dimensional quality control procedures and requirements, to be used for construction work. Annex A contains a list recommendations to be used when applicable.
|
Published |
1989-07 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
91.200
Construction technology
|
| ISO 4463-1:1989 |
Measurement methods for building — Setting-out and measurement — Part 1: Planning and organization, measuring procedures, acceptance criteria |
Deals with the different stages of the setting out work, i.e. the measuring of the primary framework (traverses, grids, etc.) on the site, the setting out of reference lines (baselines), the transfer (plumbing up) of reference lines to other floors, the setting out of position points and the levelling procedure for these different stages. Gives values for permissible deviations when measuring and setting out and recommends certain procedures and instruments to be used.
|
Published |
1989-11 |
Edition : 1 |
Number of pages : 21 |
Technical Committee |
91.200
Construction technology
|
| ISO 4463-2:1995 |
Measurement methods for building — Setting-out and measurement — Part 2: Measuring stations and targets |
Deals with the stages of establishing and marking measuring stations and targets on building sites. Examples of different stations, targets and location plans are given in annex A. This first edition together with ISO 4463-1 and ISO 4463-3 replaces ISO 4463:1979, which has been technically revised.
|
Published |
1995-12 |
Edition : 1 |
Number of pages : 28 |
Technical Committee |
91.200
Construction technology
|
| ISO 4463-3:1995 |
Measurement methods for building — Setting-out and measurement — Part 3: Check-lists for the procurement of surveys and measurement services |
Provides guidance in the form of check-lists for the surveying and setting-out services that may be required during the development and construction of buildings and ancillary works. This first edition together with ISO 4463-1 and ISO 4463-2 replaces ISO 4463:1979, which has been technically revised.
|
Published |
1995-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
91.200
Construction technology
|
| ISO 7077:1981 |
Measuring methods for building — General principles and procedures for the verification of dimensional compliance |
Indicates the principles to be applied for carrying out dimensional compliance control measurements in building construction. Deals with compliance measurements for setting out component manufacture and assembly, and the building as a whole. Applies to all types of building construction.
|
Published |
1981-10 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
91.200
Construction technology
|
| ISO 7078:1985 |
Building construction — Procedures for setting out, measurement and surveying — Vocabulary and guidance notes |
Defines terms, in English and French, that are commonly used in procedures for setting out, measurement and surveying in building construction. Gives also equivalent German terms in an annex. Contains general terms, quality of measurement, scales, measuring tools, measuring instruments and their parts, and methods of measuring.
|
Withdrawn |
1985-12 |
Edition : 1 |
Number of pages : 46 |
Technical Committee |
91.200
Construction technology
;
01.040.91
Construction materials and building (Vocabularies)
|
| ISO 7078:2020 |
Buildings and civil engineering works — Procedures for setting out, measurement and surveying — Vocabulary |
This document defines terms that are commonly used in procedures for setting out, measurement and surveying in buildings and civil engineering works.
|
Published |
2020-04 |
Edition : 2 |
Number of pages : 34 |
Technical Committee |
91.200
Construction technology
;
01.040.91
Construction materials and building (Vocabularies)
|
| ISO 7727:1984 |
Joints in building — Principles for jointing of building components — Accommodation of dimensional deviations during construction |
Is one of a series dealing with general rules and principles for the jointing of building components. Establishes a classification system for joints in building based on the ability of joints to accommodate dimensional deviations during construction. Examples of types of joints are given in an annex.
|
Published |
1984-11 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
91.200
Construction technology
|
| ISO 7976-1:1989 |
Tolerances for building — Methods of measurement of buildings and building products — Part 1: Methods and instruments |
Gives some alternative measuring methods for the determination of shape, dimensions and dimensional deviations of buildings and building products. These methods concern primarily objects the faces of which are rectilinear in shape and which have a modulus of elasticity larger than 35 kPa, for example concrete, steel, wood, hard plastic.
|
Published |
1989-03 |
Edition : 1 |
Number of pages : 80 |
Technical Committee |
91.200
Construction technology
|
| ISO 7976-2:1989 |
Tolerances for building — Methods of measurement of buildings and building products — Part 2: Position of measuring points |
Gives guidance on the position of measuring points to be used in the measurement of buildings and building products. The positions given apply for check and compliance measurement and for collecting accuracy data. Building products consisting of glass wool and similar soft materials are not the subject of this Standard.
|
Published |
1989-03 |
Edition : 1 |
Number of pages : 24 |
Technical Committee |
91.200
Construction technology
|
| ISO 8322-1:1989 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 1: Theory |
Contains the formulae used in the specification of test procedures to be adopted for the determination and assessment of the accuracy in use of measuring instruments. Applies also to the procedures used in building construction when determining and assessing the accuracy of surveying, check and compliance measurements, setting out, checking processes or when obtaining accuracy data.
|
Withdrawn |
1989-09 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
17.020
Metrology and measurement in general
;
91.200
Construction technology
|
| ISO 8322-2:1989 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 2: Measuring tapes |
Specifies test procedures to be adopted when determining and assessing the accuracy in use of tapes for measuring length. The procedures given apply when these measuring tapes are used in building construction for surveying, check and compliance measurements and for obtaining accuracy data.
|
Withdrawn |
1989-09 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
91.200
Construction technology
;
17.040.30
Measuring instruments
|
| ISO 8322-3:1989 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 3: Optical levelling instruments |
Specifies test procedures to be adopted when determining and assessing the accuracy in use of optical levelling instruments for measuring purposes. The procedures given apply when the optical levelling instruments are used in building construction for surveying, check and compliance measurements and for obtaining accuracy data.
|
Withdrawn |
1989-09 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
91.200
Construction technology
;
17.180.30
Optical measuring instruments
|
| ISO 7858-2:2000 |
Measurement of water flow in closed conduits — Combination meters for cold potable water — Part 2: Installation requirements |
|
Withdrawn |
2000-10 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
91.140.60
Water supply systems
|
| ISO 8322-4:1991 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 4: Theodolites |
Specifies test procedures used to evaluate the precision in use of theodolites for measurement of horizontal and vertical angles in the gon and degree system. Does not apply to land surveying purposes.
|
Withdrawn |
1991-11 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
91.200
Construction technology
;
17.180.30
Optical measuring instruments
|
| ISO 8322-5:1991 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 5: Optical plumbing instruments |
Specifies test procedures used to evaluate the precision of optical plummets for measurement purposes. Does not apply to land surveying purposes.
|
Withdrawn |
1991-11 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
91.200
Construction technology
;
17.180.30
Optical measuring instruments
|
| ISO 8322-6:1991 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 6: Laser instruments |
Specifies test procedures used to evaluate the precision in use of laser instruments and ancillary equipment for measurements of distances from a plane, a line or a specific gradient defined by a laser beam. Does not apply to land surveying purposes.
|
Withdrawn |
1991-11 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
31.260
Optoelectronics. Laser equipment
;
91.200
Construction technology
;
17.180.30
Optical measuring instruments
|
| ISO 8322-7:1991 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 7: Instruments when used for setting out |
Specifies test procedures used to evaluate the precision during setting out with theodolite and steel tape and with a theodolite. Does not apply to land surveying purposes.
|
Withdrawn |
1991-11 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
91.200
Construction technology
;
17.040.30
Measuring instruments
|
| ISO 8322-8:1992 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 8: Electronic distance-measuring instruments up to 150 m |
The test procedures specified apply to those types of electronic distance-measuring instruments used for surveying, control and compliance measurements and also when collecting accuracy data. Annex A gives examples of the determination of systematic errors. Annex B gives the unit lengths of various instruments.
|
Withdrawn |
1992-06 |
Edition : 1 |
Number of pages : 20 |
Technical Committee |
91.200
Construction technology
;
17.040.30
Measuring instruments
|
| ISO 8322-10:1995 |
Building construction — Measuring instruments — Procedures for determining accuracy in use — Part 10: Difference between non-glass reflectors and electronic distance-measuring prisms (traditional glass prisms) for distances up to 150 m |
Specifies test procedures to be adopted when determining the accuracy in use of the difference between non-glass reflectors and traditional electronic distance-measuring (EDM) prisms of glass used in buildung construction for distances up to 150 m. Applies only to those types of electronic distance-measuring instruments measuring to a prism or reflector.
|
Withdrawn |
1995-07 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
91.200
Construction technology
;
17.040.30
Measuring instruments
|
| ISO 12491:1997 |
Statistical methods for quality control of building materials and components |
|
Published |
1997-05 |
Edition : 1 |
Number of pages : 30 |
Technical Committee |
91.200
Construction technology
|
| ISO 4054:1980 |
Couplers, loose spigots and base-plates for use in working scaffolds made of steel tubes — Requirements and test procedure |
|
Withdrawn |
1980-04 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
91.220
Construction equipment
;
77.140.99
Other iron and steel products
|
| ISO 4872:1978 |
Acoustics — Measurement of airborne noise emitted by construction equipment intended for outdoor use — Method for determining compliance with noise limits |
Describes a procedure for measuring the weighted sound pressure levels at prescribed microphone positions in the proximity of a device or machine. The A-weighted sound power level of the source is calculated from the measured values.
|
Withdrawn |
1978-06 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
91.220
Construction equipment
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 18650-2:2014 |
Building construction machinery and equipment — Concrete mixers — Part 2: Procedure for examination of mixing efficiency |
ISO 18650-2:2014 specifies the procedure and requirements for examination of the mixing efficiency of batch-type and continuous-type concrete mixers as defined in ISO 18650-1. It is applicable to concrete mixers having a rated capacity greater than or equal to 70/50.
|
Published |
2014-09 |
Edition : 2 |
Number of pages : 19 |
Technical Committee |
91.220
Construction equipment
|
| ISO 6085:2023 |
Building construction machinery and equipment — Self-loading mobile concrete mixers — Safety requirements and verification |
This document specifies general safety requirements for self-loading mobile concrete mixers (here-after referred to as “machines”) as defined in ISO 18650-1:2021, with rigid or articulated wheeled chassis.
This document applies to machines which are designed for front or rear loading and are provided with a swinging frame where the rotating drum and the self-loading equipment (lift arms and bucket) are mounted on. Machines are also fitted with accessories such as water dosing means and a weighing system.
This document deals with all significant hazards, hazardous situations and events relevant to the machine when used as intended or under conditions of misuse reasonably foreseeable by the manufacturer.
This document is not applicable to the following:
a) machines designed primarily for earth moving, such as loaders or dumpers (see applicable parts of the ISO 20474 series);
b) truck mixers.
This document does not address hazards that can occur:
— during manufacture;
— when using machines on public roads, where specific local road regulations can apply;
— when operating in potentially explosive atmospheres.
This document is not applicable to machines manufactured before the date of its publication.
|
Published |
2023-02 |
Edition : 1 |
Number of pages : 22 |
Technical Committee |
91.220
Construction equipment
|
| ISO 11375:1998 |
Building construction machinery and equipment — Terms and definitions |
|
Published |
1998-04 |
Edition : 1 |
Number of pages : 54 |
Technical Committee |
91.220
Construction equipment
;
01.040.91
Construction materials and building (Vocabularies)
|
| ISO 11886:2002 |
Building construction machinery and equipment — Pile driving and extracting equipment — Terminology and commercial specifications |
ISO 11886:2002 specifies terms and definitions of the main types of mechanical equipment for pile driving/extracting, such as pile arrangements on the construction site, pulling, installation of piles at the point of driving, driving and extraction of piles, pile head crushing, etc. Machines for non-mechanical processing, such as the injection of small piles with supporting fluids, are not dealt with in ISO 11886:2002.
NOTE Annex A shows examples of pile driving and extracting equipment.
|
Published |
2002-08 |
Edition : 1 |
Number of pages : 30 |
Technical Committee |
91.220
Construction equipment
;
01.040.91
Construction materials and building (Vocabularies)
|
| ISO 11886:2002/Cor 1:2006 |
Building construction machinery and equipment — Pile driving and extracting equipment — Terminology and commercial specifications — Technical Corrigendum 1 |
|
Published |
2006-04 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
91.220
Construction equipment
;
01.040.91
Construction materials and building (Vocabularies)
|
| ISO/TR 12603:1996 |
Building construction machinery and equipment — Classification |
Contains a classification of machines and equipment used in the building field. This field is divided into seven classes of traditional and specified use and the different machines are classified accordingly.
|
Withdrawn |
1996-03 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
91.220
Construction equipment
|
| ISO/TR 12603:2010 |
Building construction machinery and equipment — Classification |
ISO/TR 12603:2010 classifies machinery and equipment used in the building and construction industry into three hierarchical levels, nine groups and into subgroups. It covers machines and equipment employed in the majority of works in the field, classified according to their specified use. In as far as possible, and where existent, International Standards corresponding to subgroups are specified. The ISO Technical Committees responsible for the International Standards are also given, together with, for the convenience of the user, any related European standards.
|
Published |
2010-03 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
91.220
Construction equipment
|
| ISO 13105-1:2014 |
Building construction machinery and equipment — Machinery for concrete surface floating and finishing — Part 1: Terms and commercial specifications |
ISO 13105-1:2014 defines terms and commercial specifications for machines used for concrete surface floating and finishing (also known as power trowels). This includes pedestrian-controlled equipment and ride-on equipment. It does not address strike-off type machines, commonly known as screeds.
|
Published |
2014-12 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
91.220
Construction equipment
;
01.040.91
Construction materials and building (Vocabularies)
|
| ISO/DIS 13105-1 |
Building construction machinery and equipment — Machinery for concrete surface floating and finishing — Part 1: Terms and commercial specifications |
ISO 13105-1:2014 defines terms and commercial specifications for machines used for concrete surface floating and finishing (also known as power trowels). This includes pedestrian-controlled equipment and ride-on equipment. It does not address strike-off type machines, commonly known as screeds.
|
Under development |
|
Edition : 2 |
Number of pages : 6 |
Technical Committee |
91.220
Construction equipment
;
01.040.91
Construction materials and building (Vocabularies)
|
| ISO 18651-1:2011 |
Building construction machinery and equipment — Internal vibrators for concrete — Part 1: Terminology and commercial specifications |
ISO 18651:2011 specifies the terminology and gives commercial specifications for internal vibrators used for concrete mix compaction.
|
Published |
2011-04 |
Edition : 1 |
Number of pages : 16 |
Technical Committee |
91.220
Construction equipment
|
| ISO 13105-2:2014 |
Building construction machinery and equipment — Machinery for concrete surface floating and finishing — Part 2: Safety requirements and verification |
ISO 13105-2:2014 specifies safety requirements for machines used for concrete surface floating and finishing. This includes pedestrian-controlled equipment and ride-on equipment. It is not applicable to internal or external vibrators or ancillary equipment used with internal and external vibrators, for example, air compressors, hydraulic power sources, and voltage transformers, to remote-controlled or hand-held smoothing machines and self-acting (robotic) smoothing machines, or to strike-off type machines commonly known as screeds.
It deals with significant hazards, hazardous situations, or hazardous events relevant to machinery for concrete surface floating and finishing (power trowels) when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
It is not applicable to machines which are manufactured before the date of its publication.
|
Published |
2014-12 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
13.110
Safety of machinery
;
91.220
Construction equipment
|
| ISO 13105-2:2014/Amd 1:2017 |
Building construction machinery and equipment — Machinery for concrete surface floating and finishing — Part 2: Safety requirements and verification — Amendment 1 |
|
Published |
2017-11 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
13.110
Safety of machinery
;
91.220
Construction equipment
|
| ISO/DIS 13105-2 |
Building construction machinery and equipment — Machinery for concrete surface floating and finishing — Part 2: Safety requirements and verification |
ISO 13105-2:2014 specifies safety requirements for machines used for concrete surface floating and finishing. This includes pedestrian-controlled equipment and ride-on equipment. It is not applicable to internal or external vibrators or ancillary equipment used with internal and external vibrators, for example, air compressors, hydraulic power sources, and voltage transformers, to remote-controlled or hand-held smoothing machines and self-acting (robotic) smoothing machines, or to strike-off type machines commonly known as screeds.
It deals with significant hazards, hazardous situations, or hazardous events relevant to machinery for concrete surface floating and finishing (power trowels) when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
It is not applicable to machines which are manufactured before the date of its publication.
|
Under development |
|
Edition : 2 |
Number of pages : 17 |
Technical Committee |
13.110
Safety of machinery
;
91.220
Construction equipment
|
| ISO 13442:2004 |
Tyres and rims for construction machines |
ISO 13442:2004 sets the designation, dimensions, load ratings and reference speeds for tyres and rims fitted to construction machines (backhoe loaders, small dumpers, loaders, excavators etc.) operating on building sites under loading and transport conditions.
|
Withdrawn |
2004-04 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
91.220
Construction equipment
;
83.160.99
Other tyres
|
| ISO 17740-1:2015 |
Building construction machinery and equipment — Concrete placing systems for stationary equipment — Part 1: Terminology and commercial specifications |
ISO 17740-1:2015 defines terminology and commercial specifications for concrete placing systems which are stationary.
ISO 17740-1:2015 is not applicable to concrete placing systems which are part of a mobile or trailer-mounted concrete pumping system (see ISO 21573‑1).
|
Published |
2015-07 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
91.220
Construction equipment
;
01.040.91
Construction materials and building (Vocabularies)
|
| ISO 18650-1:2004 |
Building construction machinery and equipment — Concrete mixers — Part 1: Vocabulary and general specifications |
ISO 18650-1:2004 establishes additional terminology to describe the functioning and the required and optional components for various types of concrete mixers. The content of commercial literature specifications for these types of machines is defined.
ISO 18650-1:2004 applies to concrete mixers as defined in ISO 11375; truck mixers are excluded.
|
Withdrawn |
2004-11 |
Edition : 1 |
Number of pages : 27 |
Technical Committee |
91.220
Construction equipment
;
01.040.91
Construction materials and building (Vocabularies)
|
| ISO 18650-1:2021 |
Building construction machinery and equipment — Concrete mixers — Part 1: Commercial specifications |
This document establishes the content for commercial literature for concrete mixers used either as individual machines on building sites or as components of batching plants.
Definitions refer to whole machines, their structure and parameters.
The commercial specifications establish technical characteristics of the whole machines and their components.
Truck mixers, as defined in ISO 19711‑1, are excluded from this document.
|
Published |
2021-05 |
Edition : 2 |
Number of pages : 35 |
Technical Committee |
91.220
Construction equipment
;
01.040.91
Construction materials and building (Vocabularies)
|
| ISO 18650-2:2006 |
Building construction machinery and equipment — Concrete mixers — Part 2: Procedure for examination of mixing efficiency |
ISO 18650-2:2006 specifies the procedure and requirements for examination of the mixing efficiency of batch-type and continuous-type concrete mixers as defined in ISO 18650-1. It is applicable to concrete mixers having a rated capacity greater than or equal to 70/50.
|
Withdrawn |
2006-04 |
Edition : 1 |
Number of pages : 19 |
Technical Committee |
91.220
Construction equipment
|
| ISO 18652:2005 |
Building construction machinery and equipment — External vibrators for concrete |
ISO 18652:2005 defines terms and specifies the classification, performance requirements, test methods, designation and commercial specifications of external vibrators for concrete. It is applicable only to those power-driven external vibrators used for compacting concrete mix by vibration from the outside.
|
Published |
2005-02 |
Edition : 1 |
Number of pages : 23 |
Technical Committee |
91.220
Construction equipment
|