| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO 13350:1999 |
Industrial fans — Performance testing of jet fans |
|
Withdrawn |
1999-10 |
Edition : 1 |
Number of pages : 27 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 12759-4:2019 |
Fans — Efficiency classification for fans — Part 4: Driven fans at maximum operating speed |
This document establishes a system for the classification of fan efficiency for all fan types driven by motors of nominal rating 0,125 kW and above. It applies to driven fans only, but not to the system (finished original equipment manufacturer's product, for example box fans and roof fans or ventilation system) in which they might be installed. This document describes a number of different procedures to classify the efficiency of a fan or to apply a minimum efficiency limit (MEL). Those procedures are described in:
— ISO 12759-3;
— this document (ISO 12759-4);
— ISO 12759-5;
— ISO 12759-6.
There is no method described to compare these classifications and MEL's.
|
Published |
2019-10 |
Edition : 1 |
Number of pages : 25 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 12759-5:2021 |
Fans — Efficiency classification for fans — Part 5: Jet fans |
This document establishes a classification of fan efficiency for all jet fan types driven by motors with an electrical input power range from 5,5 kW to 155 kW (and this is likely to be in the size range 500 mm to 1600 mm diameter with motors rated between 5,5 kW and 150 kW from IEC 60034-30-1).
This document is not applicable to jet fans for use in enclosed car parks.
This document can be used by legislators or regulatory bodies for defining future energy saving targets.
|
Published |
2021-06 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO/DIS 12759-6 |
Fans — Efficiency classification for fans — Part 6: Calculation of the fan energy index |
This document defines the calculation method for determining the fan energy index (FEI), which is an energy efficiency metric for fan duty points. This metric provides a standardized and consistent basis to compare fan energy performance across fan types and sizes at a given fan duty point.
This document is applicable to fans driven by motors and fans without drives. It is not applicable to circulating fans or air curtains.
The fan energy index can only be calculated for fan duty points above a minimum air power of 125 W (where air power is the product of volume flow rate and fan static pressure) or above a minimum volume flow rate of 2.0 m3/s.
|
Under development |
|
Edition : 1 |
Number of pages : 37 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 12759:2010 |
Fans — Efficiency classification for fans |
ISO 12759:2010 specifies requirements for classification of fan efficiency for all fan types driven by motors with an electrical input power range from 0,125 kW to 500 kW. It is applicable to (bare shaft and driven) fans, as well as fans integrated into products. Fans integrated into products are measured as stand-alone fans.
It is not applicable to fans for smoke and emergency smoke extraction; fans for industrial processes; fans for automotive application, trains, planes, etc.; fans for potentially explosive atmospheres; box fans, powered roof ventilators and air curtains or jet fans for use in car parks and tunnel ventilation.
|
Withdrawn |
2010-12 |
Edition : 1 |
Number of pages : 42 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 12759:2010/Amd 1:2013 |
Fans — Efficiency classification for fans — Amendment 1 |
|
Withdrawn |
2013-04 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 13253:1995 |
Ducted air-conditioners and air-to-air heat pumps — Testing and rating for performance |
Establishes performance testing and rating criteria for ducted air-conditioners using air- and water-cooled condensers and ducted air-to-air heat pumps. Is limited to systems which use a single refrigeration circuit and have one evaporator and one condenser.
|
Withdrawn |
1995-11 |
Edition : 1 |
Number of pages : 46 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 13253:2011 |
Ducted air-conditioners and air-to-air heat pumps — Testing and rating for performance |
ISO 13253:2011 specifies the standard conditions for capacity and efficiency ratings of ducted, air-cooled air-conditioners and ducted air-to-air heat pumps. ISO 13253:2011 is applicable to the test methods for determining the capacity and efficiency ratings. Residential, commercial, and industrial single-package and split-system air-conditioners and heat pumps are included. The equipment (taken to mean ducted air-conditioners and/or ducted heat pumps) shall be factory-made and electrically driven, and shall use mechanical compression.
ISO 13253:2011 is applicable to equipment utilizing one or more refrigeration systems, one outdoor unit and one or more indoor units controlled by a single thermostat/controller. ISO 13253:2011 is applicable to equipment utilizing single-, multiple- and variable-capacity components.
|
Withdrawn |
2011-07 |
Edition : 2 |
Number of pages : 89 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 13350:2015 |
Fans — Performance testing of jet fans |
ISO 13350:2015 deals with the determination of those technical characteristics needed to describe all aspects of the performance of jet fans as defined in ISO 13349. It does not cover those fans designed for ducted applications, nor those designed solely for air circulation, e.g. ceiling fans and table fans.
The test procedures described in this International Standard relate to laboratory conditions. The measurement of performance under on-site conditions is not included.
|
Published |
2015-10 |
Edition : 2 |
Number of pages : 30 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO/DIS 13350 |
Fans — Performance testing of jet fans |
|
Deleted |
|
Edition : 3 |
Number of pages : 33 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 13253:2017 |
Ducted air-conditioners and air-to-air heat pumps — Testing and rating for performance |
ISO 13253:2017 specifies performance testing, the standard conditions and the test methods for determining the capacity and efficiency ratings of air-cooled, air-conditioners and air-to-air heat pumps.
ISO 13253:2017 is applicable to the following equipment:
- ducted air-cooled air conditioners and ducted air to air heat pumps.
ISO 13253:2017 is limited to
- residential, commercial and industrial single-package, and split-system air conditioners and heat pumps,
- factory-made, electrically driven and use mechanical compression,
- utilizing single, multiple and variable capacity components, and
- multiple split-system utilizing one or more refrigeration systems, one outdoor unit and one or more indoor units, controlled by a single thermostat/controller.
The requirements of testing and rating contained in this document are based on the use of matched assemblies.
ISO 13253:2017 is not applicable to the rating and testing of the following:
a) water-source heat pumps or water-cooled air-conditioners;
b) multi-split-system air-conditioners and air-to-air heat pumps (see ISO 15042 for testing of such equipment);
c) mobile (windowless) units having a condenser exhaust duct;
d) individual assemblies not constituting a complete refrigeration system;
e) equipment using the absorption refrigeration cycle;
f) non-ducted equipment (see ISO 5151 for testing of such equipment);
g) ducted air conditioners and/or ducted heat pumps, rated at less than 8 kW and intended to operate at external static pressures of less than 25 Pa, controlled by a single thermostat/controller (refer to ISO 5151).
ISO 13253:2017 does not cover the determination of seasonal efficiencies, which can be required in some countries because they provide a better indication of efficiency under actual operating conditions.
NOTE Throughout this document, the terms "equipment" and "systems" mean "air-conditioners" and/or "heat pumps".
|
Published |
2017-07 |
Edition : 3 |
Number of pages : 89 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 13253:2017/Amd 1:2020 |
Ducted air-conditioners and air-to-air heat pumps — Testing and rating for performance — Amendment 1 |
|
Published |
2020-10 |
Edition : 3 |
Number of pages : 1 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 13261-1:1998 |
Sound power rating of air-conditioning and air-source heat pump equipment — Part 1: Non-ducted outdoor equipment |
|
Published |
1998-04 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 13261-2:1998 |
Sound power rating of air-conditioning and air-source heat pump equipment — Part 2: Non-ducted indoor equipment |
|
Published |
1998-04 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 13347-1:2004 |
Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 1: General overview |
ISO 13347:2004 deals with the determination of the acoustic performance of industrial fans. In addition, it may be used to determine the acoustic performance of fans combined with an ancillary device such as a roof cowl or damper or, where the fan is fitted with a silencer, the sound power resulting from the fan and silencer combination.
|
Published |
2004-08 |
Edition : 1 |
Number of pages : 34 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 13347-1:2004/Amd 1:2010 |
Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 1: General overview — Amendment 1 |
|
Published |
2010-11 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 13347-1:2004/Cor 1:2006 |
Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 1: General overview — Technical Corrigendum 1 |
|
Published |
2006-10 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 13347-2:2004 |
Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 2: Reverberant room method |
ISO 13347-2:2004 gives a detailed description of reverberant room methods for the determination of fan sound power levels. It is for use under standardized laboratory conditions and recognises that tests in situ are subject to increased uncertainty. These test procedures are not necessarily appropriate to site test conditions. Acoustic system effects are presently the subject of considerable research effort.
ISO 5136, which covers the in-duct method, and ISO 10302 for small fans, should be used in conjunction with ISO 13347-2:2004.
|
Published |
2004-08 |
Edition : 1 |
Number of pages : 22 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 13347-2:2004/Cor 1:2006 |
Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 2: Reverberant room method — Technical Corrigendum 1 |
|
Published |
2006-10 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 13351:1996 |
Industrial fans — Dimensions |
|
Withdrawn |
1996-06 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 13347-3:2004 |
Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 3: Enveloping surface methods |
ISO 13347-3:2004 applies to industrial fans as defined in ISO 5801 and ISO 13349. It is limited to the determination of airborne sound emission for the specified set-ups. Vibration is not measured, nor is the sensitivity of airborne sound emission to vibration effects determined.
The sizes of fan which can be tested in accordance with ISO 13347-3:2004 are limited only by the practical aspects of the test set-up. Dimensional limitations, test fan dimensions, and air performance will control the room size, power and mounting requirements for the test fan.
The test arrangements in ISO 13347-3:2004 establish the laboratory conditions necessary for a successful test. Rarely will it be possible to meet these requirements in situ and ISO 13347-3:2004 is not intended for field measurements. Intending users are reminded that, in these situations, there may well be additional acoustic system effects where inlet and outlet conditions at the fan are less than ideal.
The enveloping surface methods may be used for the determination of open inlet and/or open outlet sound power level of fans for standardized installation types.
An estimation (with increased uncertainty) of ducted sound power for fans too small, or otherwise inconvenient, for testing by the in-duct method described in ISO 5136 may also be obtained by the addition of end reflection corrections.
|
Published |
2004-08 |
Edition : 1 |
Number of pages : 22 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 13347-3:2004/Amd 1:2010 |
Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 3: Enveloping surface methods — Amendment 1 |
|
Published |
2010-11 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 13347-3:2004/Cor 1:2006 |
Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 3: Enveloping surface methods — Technical Corrigendum 1 |
|
Published |
2006-11 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 13347-4:2004 |
Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 4: Sound intensity method |
ISO 13347-4:2004 applies to industrial fans as defined in ISO 5801 and ISO 13349. It is limited to the determination of airborne sound emission for the specified set-ups. Vibration is not measured, nor is the sensitivity of airborne sound emission to vibration effects determined.
The sizes of the fan, which can be tested in accordance with ISO 13347-4:2004, are limited only by the practical aspects of the test installations.
ISO 13347-4:2004 determines sound power by using sound intensity measurements on a measurement surface which encloses the sound source. It provides guidelines on the acoustical environment, ambient noise, measurement surface, and number of measurements. The test set-ups are generally designed to represent the physical orientation of a fan installed in accordance with ISO 5801 and also used in ISO 13347-2.
|
Published |
2004-08 |
Edition : 1 |
Number of pages : 25 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 13347-4:2004/Cor 1:2006 |
Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 4: Sound intensity method — Technical Corrigendum 1 |
|
Published |
2006-10 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
17.140.20
Noise emitted by machines and equipment
|
| ISO 13348:2006 |
Industrial fans — Tolerances, methods of conversion and technical data presentation |
ISO 13348:2006 specifies performance tolerances and the technical data presentation of industrial fans of all types. It does not apply for fans designed solely for low-volume air circulation, such as those used for household or similar purposes (ceiling and table fans, extractor fans, etc.).
ISO 13348:2006 covers the four installation categories defined in ISO 5801:A, free inlet, free outlet; B, free inlet, ducted outlet; C, ducted inlet, free outlet;D, ducted inlet, ducted outlet.
|
Withdrawn |
2006-03 |
Edition : 1 |
Number of pages : 53 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 13348:2007 |
Industrial fans — Tolerances, methods of conversion and technical data presentation |
ISO 13348:2007 specifies performance tolerances and the technical data presentation of industrial fans of all types. It does not apply for fans designed solely for low-volume air circulation, such as those used for household or similar purposes (ceiling and table fans, extractor fans, etc.).
ISO 13348:2007 covers the four installation categories defined in ISO 5801: A, free inlet, free outlet; B, free inlet, ducted outlet; C, ducted inlet, free outlet; D, ducted inlet, ducted outlet.
|
Published |
2007-01 |
Edition : 2 |
Number of pages : 53 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 13349-1:2022 |
Fans — Vocabulary and definitions of categories — Part 1: Vocabulary |
This document defines terms in the field of fans used for all purposes.
It is not applicable to electrical safety.
|
Published |
2022-09 |
Edition : 3 |
Number of pages : 23 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
01.040.23
Fluid systems and components for general use (Vocabularies)
|
| ISO 14617-9:2002 |
Graphical symbols for diagrams — Part 9: Pumps, compressors and fans |
This part of ISO 14617 specifies graphical symbols for pumps, compressors and fans, used mainly for transportation, in diagrams.
|
Published |
2002-09 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
23.080
Pumps
;
23.120
Ventilators. Fans. Air-conditioners
;
23.140
Compressors and pneumatic machines
;
01.080.30
Graphical symbols for use on mechanical engineering and construction drawings, diagrams, plans, maps and in relevant technical product documentation
|
| ISO 14694:2003 |
Industrial fans — Specifications for balance quality and vibration levels |
ISO 14694:2003 gives specifications for vibration and balance limits of fans for all applications except those designed solely for air circulation, for example, ceiling fans and table fans. However, it is limited to fans of all types installed with a power of less than 300 kW or to commercially available standard electric motor with a maximum power of 355 kW (following an R20 series). For fans of greater power than this, the applicable limits are those given in ISO 10816 - 3. Where the fans in an installation have varying powers both above and below 300 kW, and have been the subject of a single contract, then the manufacturer and purchaser shall agree on the appropriate standard to be used. This should normally be based on the majority of units.
Fan-equipment foundations and installation practices are beyond the scope of ISO 14694:2003. Foundation design and fan installation are not normally the responsibilities of the fan manufacturer. It is fully expected that the foundations upon which the fan is mounted will provide the support and stability necessary to meet the vibration criteria of the fan as it is delivered from the factory.
ISO 14694:2003 is intended to cover only the balance or vibration of the fan and does not take into account the effect of fan vibration on personnel, equipment or processes.
|
Published |
2003-03 |
Edition : 1 |
Number of pages : 39 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
21.120.40
Balancing and balancing machines
|
| ISO 14694:2003/Amd 1:2010 |
Industrial fans — Specifications for balance quality and vibration levels — Amendment 1 |
|
Published |
2010-11 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
21.120.40
Balancing and balancing machines
|
| ISO 14695:2003 |
Industrial fans — Method of measurement of fan vibration |
ISO 14695:2003 describes a method of measuring the vibrational characteristics of fans of all types, except those designed solely for air circulation, for example, ceiling fans and table fans. However, it is limited to fans of all types installed with a power of less than 300 kW. For fans of greater power than this, the methods described in ISO 10816-1 and the applicable limits given in ISO 10816-3 may be used. ISO 14695:2003 gives a general method only and does not give criteria for interpretation of data (see ISO 14694).
ISO 14695:2003 specifies the measurement of vibration that may be recorded as overall root-mean- square (r.m.s.) velocity, acceleration or displacement, or in terms of a frequency spectrum, within the appropriate frequency range. Methods of testing when suspended on elastic ropes or when installed on resilient mountings are included.
It is recognized that the oscillatory forces at mounting points can be a useful measurement for analysing the effects on support structures; but such measurements are outside the scope of ISO 14695:2003.
|
Published |
2003-04 |
Edition : 1 |
Number of pages : 33 |
Technical Committee |
17.160
Vibrations, shock and vibration measurements
;
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 14695:2003/Cor 1:2009 |
Industrial fans — Method of measurement of fan vibration — Technical Corrigendum 1 |
|
Published |
2009-03 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
17.160
Vibrations, shock and vibration measurements
;
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 15042:2011 |
Multiple split-system air-conditioners and air-to-air heat pumps — Testing and rating for performance |
ISO 15042:2011 establishes performance testing and rating criteria for factory-made residential, commercial and industrial, electrically-driven, mechanical-compression, air-cooled air-conditioners and air-to-air heat pumps, described as basic multi-split systems, modular multi-split systems and modular heat recovery multi-split systems. These multi-split systems include air-to-air systems with non-ducted and/or ducted indoor units with integral fans and indoor units supplied without fans.
ISO 15042:2011 is limited to single and multiple circuit split-systems which utilize one or more compressors with no more than two steps of control of the outdoor unit. It is also limited to split-systems with a single refrigeration circuit which utilize one or more variable-speed compressors or alternative compressor combinations for varying the capacity of the system by three or more steps. These split-systems are designed to operate with a combination of one or more outdoor units and two or more indoor units designed for individual operation, and such modular systems that are capable of transferring recovered heat from one or more indoor units to other units in the same system.
|
Withdrawn |
2011-11 |
Edition : 1 |
Number of pages : 94 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 8555-1:1987 |
Hardware for furniture — Terms for furniture fittings — Part 1: Assembly fittings |
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
97.140
Furniture
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 15042:2017 |
Multiple split-system air conditioners and air-to-air heat pumps — Testing and rating for performance |
ISO 15042:2017 specifies the performance testing, the standard conditions and the test methods for determining the capacity and efficiency ratings of air-cooled air conditioners and air-to-air heat pumps.
ISO 15042:2017 is applicable to the following equipment:
-― basic multi-split systems, modular multi-split systems and modular heat recovery multi-split systems. These multi-split systems include air-to-air systems with non-ducted and/or ducted indoor units with integral fans and indoor units supplied without fans.
ISO 15042:2017 is limited to:
- residential, commercial and industrial split-system air conditioners and heat pumps;
- factory-made, electrically driven and use mechanical compression;
- single- and multiple-circuit split-systems which utilize one or more compressors with no more than two steps of control of the outdoor unit;
or
- split-systems with a single refrigeration circuit which utilize one or more variable-speed compressors or alternative compressor combinations for varying the capacity of the system by three or more steps.
These split-systems are designed to operate with a combination of one or more outdoor units and two or more indoor units designed for individual operation, and such modular systems are capable of transferring recovered heat from one or more indoor units to other units in the same system.
The requirements of testing and rating contained in this document are based on the use of matched assemblies.
ISO 15042:2017 is not applicable to the rating and testing of the following:
a) water-cooled or water source equipment;
b) mobile (single-duct) units having a condenser exhaust duct;
c) individual assemblies not constituting a complete refrigeration system;
d) equipment using the absorption refrigeration cycle.
e) ducted air conditioners and/or ducted heat pumps, rated at less than 8 kW and intended to operate at external static pressures of less than 25 Pa, controlled by a single thermostat/controller (refer to ISO 5151);
f) multiple split-system utilizing one or more refrigeration systems, one outdoor unit and one or more indoor units, controlled by a single thermostat/controller (refer to ISO 5151 or ISO 13253).
ISO 15042:2017 does not cover the determination of seasonal efficiencies or seasonal part-load performances, which can be required in some countries because they provide a better indication of efficiency under actual operating conditions.
NOTE Throughout this document, the terms "equipment" and "systems" mean "multi-split air conditioners" and/or "multi-split heat pumps".
|
Published |
2017-07 |
Edition : 2 |
Number of pages : 97 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 15042:2017/Amd 1:2020 |
Multiple split-system air conditioners and air-to-air heat pumps — Testing and rating for performance — Amendment 1 |
|
Published |
2020-10 |
Edition : 2 |
Number of pages : 1 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO/TR 16219:2020 |
Fans — System effects and system effect factors |
This document deals with the likely degradation of air performance of fans tested in standardized airways in accordance with ISO 5801 when compared with the performance of fans tested under actual site conditions. It deals with the performance of a number of generic types of fan and fittings. The results given are intended as guidelines and only provide trends, as the system effect depends on the exact geometry of the fan and disturbing component.
The test data presented in this document are taken from an extensive experimental program conducted 20 years ago by NEL (National Engineering Laboratory, UK), mainly on axial and centrifugal fans. Data are also taken from several research projects financially supported by ASHRAE, some of them being carried out in the AMCA laboratory in Chicago, as well as from results published previously by individual fan manufacturers.
|
Published |
2020-09 |
Edition : 1 |
Number of pages : 83 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 16358-1:2013 |
Air-cooled air conditioners and air-to-air heat pumps — Testing and calculating methods for seasonal performance factors — Part 1: Cooling seasonal performance factor |
ISO 16358-1:2013 specifies the testing and calculating methods for seasonal performance factor of equipment covered by ISO 5151, ISO 13253 and ISO 15042.
ISO 16358-1:2013 also specifies the seasonal performance test conditions and the corresponding test procedures for determining the seasonal performance factor of equipment, as specified above, under mandatory test conditions and is intended for use only in marking, comparison, and certification purposes. For the purposes of ISO 16358-1:2013, the rating conditions are those specified under T1 in the reference standards above. The procedures in ISO 16358-1:2013 may be used for other temperature conditions.
ISO 16358-1:2013 does not apply to the testing and rating of:
water-source heat pumps or water-cooled air conditioners;
portable units having a condenser exhaust duct;
individual assemblies not constituting a complete refrigeration system; or
equipment using the absorption refrigeration cycle.
|
Published |
2013-04 |
Edition : 1 |
Number of pages : 26 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16358-1:2013/Amd 1:2019 |
Air-cooled air conditioners and air-to-air heat pumps — Testing and calculating methods for seasonal performance factors — Part 1: Cooling seasonal performance factor — Amendment 1 |
|
Published |
2019-04 |
Edition : 1 |
Number of pages : 21 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16358-1:2013/Cor 1:2013 |
Air-cooled air conditioners and air-to-air heat pumps — Testing and calculating methods for seasonal performance factors — Part 1: Cooling seasonal performance factor — Technical Corrigendum 1 |
|
Published |
2013-11 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 4814:1980 |
Household sewing machines — Determination of stability of needle thread tension |
Specifies a method of test for determining the variation of needle thread tension at given positions of the tension regulator. The method is applicable to motor-operated household sewing machines, but it may also be possible to apply it to hand- or treadle-operated machines. Includes additionally to principle, material and apparatus, procedure, expression of results and test report an annex which specifies the cotton thread.
|
Withdrawn |
1980-02 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
61.080
Sewing machines and other equipment for the clothing industry
|
| ISO 4210-9:2014 |
Cycles — Safety requirements for bicycles — Part 9: Saddles and seat-post test methods |
ISO 4210-9:2014 specifies saddle and seat-post test methods for ISO 4210‑2.
|
Withdrawn |
2014-07 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
43.150
Cycles
|
| ISO 16358-2:2013 |
Air-cooled air conditioners and air-to-air heat pumps — Testing and calculating methods for seasonal performance factors — Part 2: Heating seasonal performance factor |
ISO 16358-2:2013 specifies the testing and calculating methods for seasonal performance factor of equipment covered by ISO 5151, ISO 13253 and ISO 15042. For the purposes of ISO 16358-2:2013, it is assumed that any make-up heating will be provided by electric heaters running concurrently with the heat pump.
ISO 16358-2:2013 also specifies the seasonal performance test conditions and the corresponding test procedures for determining the seasonal performance factor of equipment, as specified above, under mandatory test conditions and is intended for use only in marking, comparison, and certification purposes.
ISO 16358-2:2013 does not apply to the testing and rating of:
water-source heat pumps or water-cooled air conditioners;
portable units having a condenser exhaust duct;
individual assemblies not constituting a complete refrigeration system; or
equipment using the absorption refrigeration cycle.
|
Published |
2013-04 |
Edition : 1 |
Number of pages : 38 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16358-2:2013/Cor 1:2013 |
Air-cooled air conditioners and air-to-air heat pumps — Testing and calculating methods for seasonal performance factors — Part 2: Heating seasonal performance factor — Technical Corrigendum 1 |
|
Published |
2013-11 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16358-3:2013 |
Air-cooled air conditioners and air-to-air heat pumps — Testing and calculating methods for seasonal performance factors — Part 3: Annual performance factor |
ISO 16358-3:2013 specifies the testing and calculating methods for seasonal performance factor of equipment covered by ISO 5151, ISO 13253 and ISO 15042.
ISO 16358-3:2013 also specifies the seasonal performance test conditions and the corresponding test procedures for determining the seasonal performance factor of equipment, as specified above, under mandatory test conditions and is intended for use only in marking, comparison, and certification purposes.
ISO 16358-3:2013 does not apply to the testing and rating of:
water-source heat pumps or water-cooled air conditioners;
portable units having a condenser exhaust duct;
individual assemblies not constituting a complete refrigeration system; or
equipment using the absorption refrigeration cycle.
|
Published |
2013-04 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO/TS 16491:2012 |
Guidelines for the evaluation of uncertainty of measurement in air conditioner and heat pump cooling and heating capacity tests |
ISO/TS 16491:2012 gives guidance on the practical applications of the principles of performance measurement of air-cooled air-conditioners and air-to-air heat pumps as described in ISO 5151, ISO 13253, and ISO 15042.
|
Published |
2012-12 |
Edition : 1 |
Number of pages : 28 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16494-1:2022 |
Heat recovery ventilators and energy recovery ventilators — Method of test for performance — Part 1: Development of metrics for evaluation of energy related performance |
This document specifies a method of testing the ventilation and energy related performance of heat recovery ventilators (HRVs) and energy recovery ventilators (ERVs) that do not contain any supplemental heating (except for defrost), cooling, humidification, or dehumidification components.
Exchanger types of HRVs and ERVs are
a) fixed-plate exchangers (also known as recuperators),
b) rotary exchangers, including heat wheels and total energy wheels (also known as regenerators), and
c) heat pipe exchangers using a heat transfer medium, excluding those using mechanical pumping,
This document does not provide a method for measuring the response of exchangers to the formation of frost.
|
Published |
2022-06 |
Edition : 1 |
Number of pages : 40 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 16494-1:2022/DAmd 1 |
Heat recovery ventilators and energy recovery ventilators — Method of test for performance — Part 1: Development of metrics for evaluation of energy related performance — Amendment 1 |
|
Under development |
|
Edition : 1 |
Number of pages : 9 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO/TR 16494-2:2019 |
Heat recovery ventilators and energy recovery ventilators — Method of test for performance — Part 2: Assessment of measurement uncertainty of performance parameters |
This document provides guidance for practical applications of those principles in the measurement of the performance of ventilators falling under the scope of ISO 16494:2014. The references listed in the Bibliography give detailed information on the principles and theory of uncertainty as applied to measurements.
|
Published |
2019-03 |
Edition : 1 |
Number of pages : 43 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 16494:2014 |
Heat recovery ventilators and energy recovery ventilators — Method of test for performance |
ISO 16494:2014 prescribes a method of testing the ventilation and energy related performance of heat recovery ventilators (HRVs)and energy recovery ventilators (ERVs) that do not contain any supplemental heating (except for defrost), cooling, humidification or dehumidification components.
|
Withdrawn |
2014-11 |
Edition : 1 |
Number of pages : 38 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 18326:2018 |
Non-ducted portable air-cooled air conditioners and air-to-air heat pumps having a single exhaust duct — Testing and rating for performance |
This document specifies the standard conditions for capacity and efficiency ratings of non-ducted portable air-cooled air conditioners having a single exhaust duct and non-ducted portable air-cooled heat pumps having a single exhaust duct. Such air conditioners and heat pumps may include an evaporatively cooled condenser cooled by air and the evaporation of:
a) condensate collected from the evaporator;
b) external supplementary water stored in a supplementary water tank; or
c) both a) and b).
This document also specifies the test methods for determining the capacity and efficiency ratings.
This document applies to equipment that is factory-made, electrically driven and uses mechanical compression. This document is applicable to equipment utilizing one or more refrigeration systems.
This document is not applicable to the rating and testing of the following:
i) Water-source heat pumps or water-cooled air conditioners;
ii) Multi-split-system air conditioners and air-to-air heat pumps (see ISO 15042:2017 for the testing of such equipment);
iii) Individual assemblies not constituting a complete refrigeration system;
iv) Equipment using the absorption refrigeration cycle;
v) Ducted equipment (see ISO 13253:2017 for the testing of such equipment);
vi) Evaporative coolers or any other cooling systems that are not of the vapour compression type;
vii) Dehumidifiers;
viii) Spot coolers.
|
Published |
2018-09 |
Edition : 1 |
Number of pages : 47 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 18326:2018/Amd 1:2021 |
Non-ducted portable air-cooled air conditioners and air-to-air heat pumps having a single exhaust duct — Testing and rating for performance — Amendment 1 |
|
Published |
2021-05 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
27.080
Heat pumps
|
| ISO 21773:2021 |
Methods of test and characterization of performance for energy recovery components |
This document specifies methods for testing and characterizing the performance of air-to-air heat/energy exchangers when used as devices to transfer heat or heat and water vapor between two airstreams used in ventilation systems. It also specifies methods to characterize the performance of exchangers for use in calculation of the energy performance of buildings. This document is applicable to:
— fixed-plate exchangers (also known as recuperators),
— rotary exchangers, including heat wheels and total energy wheels (also known as regenerators),
— heat pipe exchangers using a heat transfer medium, excluding those using mechanical pumping.
This document does not provide a method for measuring the response of exchangers to the formation of frost.
|
Published |
2021-06 |
Edition : 1 |
Number of pages : 44 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
91.120.10
Thermal insulation of buildings
|
| ISO/DIS 24660 |
Fans — Determination of airflow propelled through an open personnel door by a positive pressure ventilator |
|
Under development |
|
Edition : 1 |
Number of pages : 10 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 27327-1:2009 |
Fans — Air curtain units — Part 1: Laboratory methods of testing for aerodynamic performance rating |
ISO 27327-1:2009 establishes uniform methods for laboratory testing of air curtain units to determine aerodynamic performance in terms of airflow rate, outlet air velocity uniformity, power consumption and air velocity projection, for rating or guarantee purposes.
ISO 27327-1:2009 is not applicable to the specification of test procedures to be used for design, production or field testing.
|
Published |
2009-06 |
Edition : 1 |
Number of pages : 29 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO/WD 27327-1 |
Fans — Air curtain units — Part 1: Laboratory methods of testing for aerodynamic performance rating |
|
Deleted |
|
Edition : 2 |
|
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 27327-2:2014 |
Fans — Air curtain units — Part 2: Laboratory methods of testing for sound power |
ISO 27327-2:2014 deals with the determination of the acoustic performance of air curtain units. In addition, it can be used to determine the acoustic performance of air curtain units combined with an ancillary device.
|
Published |
2014-02 |
Edition : 1 |
Number of pages : 38 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
;
17.140.20
Noise emitted by machines and equipment
|
| ISO/DTR 27327-3 |
Fans — Air curtain units — Part 3: Test methods to determine energy effectiveness |
|
Under development |
|
Edition : 1 |
|
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| IEC/DIS 63086-2-1 |
Household and similar electrical air cleaning appliances - Methods for measuring the performance — Part 2-1: Particular requirements for determination of reduction of particles |
|
Under development |
|
Edition : 1 |
Number of pages : 25 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| IEC/DPAS 63086-3-1 |
Household and similar electrical air cleaning appliances — Methods for measuring the performance — Part 3-1: Particular requirements for reduction of microorganisms |
|
Under development |
|
Edition : 1 |
Number of pages : 38 |
Technical Committee |
23.120
Ventilators. Fans. Air-conditioners
|
| ISO 4815:1980 |
Household sewing machines — Determination of sewing capacity |
The method for the determination of the swing capacity is applicable to motor-operated household sewing machines, but it may also be possible to apply it to hand- or treadle-operated machines. Includes additionally to definition, principle, preparation of the sewing machine, procedure, expression of results and test report an annex which specifies material and apparatus.
|
Withdrawn |
1980-09 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
61.080
Sewing machines and other equipment for the clothing industry
|
| ISO 4817:1984 |
Household sewing machines — Determination of directional stability (drift) |
The directional stability (drift) is caused by irregularities of the feed mechanism as an individual machine funktion, without using a sewing thread. The method is applicable to motor-operated household sewing machines, but it may also be possible to apply it to hand- or treadle-operated machines. Includes additionally to definitions, principle, preparation of the sewing machine, prodcedure, expression of results and test report an annex which specifies material and apparatus.
|
Withdrawn |
1984-11 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
61.080
Sewing machines and other equipment for the clothing industry
|
| ISO 4818:1984 |
Household sewing machines — Determination of creep of one ply of material over another |
The method is applicable to motor-operated household sewing machines, but it may also be possible to apply it to hand- or treadle-operated machines. Includes additionally to definition, principle, preparation of the sewing machine, procedure, expression of results and test report an annex which specifies material and apparatus.
|
Withdrawn |
1984-10 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
61.080
Sewing machines and other equipment for the clothing industry
|
| ISO 4819:1983 |
Household sewing machines — Determination of reproducibility of stitch length setting |
The method determines the stitch length at constant setting of the stitch length setting control after various adjustments and is applicable to motor-operated household sewing machines, but it may also be possible to apply it to hand- or treadle- operated machines. Includes additionally to principle, preparation of the sewing machine, procedure, expression of results and test report an annex which specifies material and apparatus.
|
Withdrawn |
1983-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
61.080
Sewing machines and other equipment for the clothing industry
|
| ISO 7114:1990 |
Household sewing machines — Numerical classification |
Establishes a numerical classification of sewing machines. Gives the classification criteria the characteristics of which are tabulated in tables 1 to 7 respectively.
|
Withdrawn |
1990-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
61.080
Sewing machines and other equipment for the clothing industry
|
| ISO 8239:1987 |
Sewing machines needles — Fitting dimensions — Tolerances and combinations |
ISO 8239 specifies the fitting dimensions of needles and needle holders. It defines general terms for sewing machine needles and specifies the tolerances for their fit in the needle holder. In addition to the rangers of dimensions for the nominal shank diameter and the length from butt to eye, ISO 8239 also indicates the preferred combinations of these two dimensions. In order to ensure the interchangeability and to reduce the variety of needles these should serve as a guide when designing new sewing machines and/or sewing machine needles.
|
Published |
1987-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
61.080
Sewing machines and other equipment for the clothing industry
|
| ISO 10821:2005 |
Industrial sewing machines — Safety requirements for sewing machines, units and systems |
ISO 10821:2005 identifies hazards and specifies safety requirements applicable to sewing machines, sewing units and sewing systems designed for professional (industrial, commercial or laboratory) use in industries including the clothing and footwear, leather goods, shirts and blousery, hosiery and knitwear, lingerie, glove, upholstery and packaging industries, and in shoe repair. The use of such machines in other industries could give rise to hazards not considered. It is not applicable to shoe bottom stitching machines, large shuttle embroidery machines in accordance with ISO 11111 or household sewing machines in accordance with IEC 60335-2-28.
|
Published |
2005-07 |
Edition : 1 |
Number of pages : 76 |
Technical Committee |
61.080
Sewing machines and other equipment for the clothing industry
|
| ISO 10821:2005/Amd 1:2009 |
Industrial sewing machines — Safety requirements for sewing machines, units and systems — Amendment 1 |
|
Published |
2009-03 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
61.080
Sewing machines and other equipment for the clothing industry
|
| ISO 105-C12:2004 |
Textiles - Tests for colour fastness — Part C12: Colour fastness to industrial laundering |
ISO 105-C12:2004 specifies methods for determining the resistance of the colour of textiles of all kinds exposed to all forms of industrial laundering procedures.
|
Published |
2004-11 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
97.060
Laundry appliances
;
59.080.01
Textiles in general
|
| ISO 105-C12:2004/Cor 1:2007 |
Textiles - Tests for colour fastness — Part C12: Colour fastness to industrial laundering — Technical Corrigendum 1 |
|
Withdrawn |
2007-03 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
97.060
Laundry appliances
;
59.080.01
Textiles in general
|
| ISO 6804:1991 |
Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers — Specification |
Specifies requirements for two types of hoses. Type 1: for unheated water supply only. Type 2: for heated water supply (max. 90°C). This second edition cancels and replaces the first edition (1982).
|
Withdrawn |
1991-07 |
Edition : 2 |
Number of pages : 5 |
Technical Committee |
97.060
Laundry appliances
;
83.140.40
Hoses
;
97.040.40
Dishwashers
|
| ISO 6804:2009 |
Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers — Specification |
ISO 6804:2009 specifies the requirements for three types of rubber or plastics inlet hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10 bar).
It is applicable to the following types of hose:
Type 1: rubber hoses for unheated water supply (maximum temperature 70 °C).
Type 2: rubber hoses for heated water supply (maximum temperature 90 °C).
Type 3: plastics hoses for unheated water supply (maximum temperature 60 °C).
|
Withdrawn |
2009-09 |
Edition : 3 |
Number of pages : 13 |
Technical Committee |
97.060
Laundry appliances
;
83.140.40
Hoses
;
97.040.40
Dishwashers
|
| ISO 6804:2016 |
Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers — Specification |
ISO 6804:2016 specifies the requirements for three types of rubber or plastics inlet hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10 bar).
It is applicable to the following types of hose:
- type 1: rubber hoses for unheated water supply (maximum temperature 70 °C);
- type 2: rubber hoses for heated water supply (maximum temperature 90 °C);
- type 3: plastics hoses for unheated water supply (maximum temperature 60 °C).
There may be national requirements for hose fittings and hoses conveying drinking water which must be complied with.
|
Published |
2016-11 |
Edition : 4 |
Number of pages : 13 |
Technical Committee |
97.060
Laundry appliances
;
83.140.40
Hoses
;
97.040.40
Dishwashers
|
| ISO/PRF 6804 |
Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers — Specification |
ISO 6804:2016 specifies the requirements for three types of rubber or plastics inlet hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10 bar).
It is applicable to the following types of hose:
- type 1: rubber hoses for unheated water supply (maximum temperature 70 °C);
- type 2: rubber hoses for heated water supply (maximum temperature 90 °C);
- type 3: plastics hoses for unheated water supply (maximum temperature 60 °C).
There may be national requirements for hose fittings and hoses conveying drinking water which must be complied with.
|
Under development |
2023-05 |
Edition : 5 |
Number of pages : 13 |
Technical Committee |
97.060
Laundry appliances
;
83.140.40
Hoses
;
97.040.40
Dishwashers
|
| ISO 7772-1:1998 |
Assessment of industrial laundry machinery by its effect on textiles — Part 1: Washing machines |
|
Withdrawn |
1998-06 |
Edition : 1 |
Number of pages : 33 |
Technical Committee |
97.060
Laundry appliances
;
59.080.01
Textiles in general
|
| ISO 7772-2:1996 |
Assessment of industrial laundry machinery by its effect on textiles — Part 2: Extracting machines |
Describes methods for the assessment of extracting machines in which water is removed mechanically from textiles in their wet state after washing.
|
Withdrawn |
1996-09 |
Edition : 1 |
Number of pages : 16 |
Technical Committee |
97.060
Laundry appliances
;
59.080.01
Textiles in general
|
| ISO 7772-3:1996 |
Assessment of industrial laundry machinery by its effect on textiles — Part 3: Flatwork-ironing machines |
Describes methods for the assessment of flatwork-ironing machines that are used in the laundering field. Applies to ironing machines heated by steam, thermal fluid, gas or electrical power.
|
Withdrawn |
1996-09 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
97.060
Laundry appliances
;
59.080.01
Textiles in general
|
| ISO 7772-4:1996 |
Assessment of industrial laundry machinery by its effect on textiles — Part 4: Batch-drying tumblers |
Describes methods for the assessment of industrial drying tumbler machines in which the damp washing is loosened and partially or completely dried under the action of heated air and mechanical energy.
|
Withdrawn |
1996-09 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
97.060
Laundry appliances
;
59.080.01
Textiles in general
|
| ISO 8229:1991 |
Operations and baths relating to dry-cleaning machines — Vocabulary |
Specifies 22 terms and definitions in English and French. Some may be used with different meanings in other fields. Contains the alphabetical indexes in English and French.
|
Published |
1991-08 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
97.060
Laundry appliances
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 8230-1:2008 |
Safety requirements for dry-cleaning machines — Part 1: Common safety requirements |
ISO 8230-1:2008 specifies common safety requirements for dry-cleaning machines. It is applicable to dry-cleaning machines of all sizes intended for industrial and commercial use for the cleaning of articles made of textile, leather, furs and skins, using exclusively either perchloroethylene or combustible solvent as the cleaning medium.
It is not applicable to: machines placed at the disposal of the general public (self-service); barrier machines; transfer machines; ironing presses (see ISO 10472-1 and ISO 10472-6); ancillary equipment, e.g. room ventilation equipment, waste recuperation systems of the still, external water cooling systems or external systems for solvent recovery from the still sludge.
ISO 8230-1:2008 deals with all significant hazards arising from the use of the dry‑cleaning machine, where “use of the dry‑cleaning machine” comprises both intended use and foreseeable abnormal situations and includes commissioning, use and maintenance. It defines the common safety requirements for dry‑cleaning machines and is intended to be used in conjunction with ISO 8230‑2 and ISO 8230‑3, as relevant. Specific requirements in ISO 8230‑2 and ISO 8230‑3 take precedence over the respective requirements of ISO 8230-1.
ISO 8230-1:2008 does not deal with hazards caused by processing items that can create an explosive atmosphere (e.g. printers' wipers containing a low-flash solvent), nor with machines processing loads that can contain “foreign solvents”, which could lead to a change in a property (characteristic) of the cleaning solvent, e.g. cause foaming or make it carcinogenic.
|
Published |
2008-10 |
Edition : 1 |
Number of pages : 31 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 8230-2:2008 |
Safety requirements for dry-cleaning machines — Part 2: Machines using perchloroethylene |
ISO 8230-2:2008 specifies safety requirements for dry-cleaning machines that exclusively use perchloroethylene (or “perc”) as their cleaning medium. It is applicable to such dry-cleaning machines, within the scope of ISO 8230-1, when they are used as intended and under conditions of misuse that are reasonably foreseeable by the manufacturer.
ISO 8230-2:2008, in conjunction with ISO 8230-1, deals with all significant hazards, significant hazardous situations and significant hazardous events that have been identified as being significant to the types of machines covered by ISO 8230-2:2008 and which require specific action by the designer or manufacturer to eliminate or reduce the risk.
It deals with the following significant hazards specific to the use of perc, which can lead to the inhalation of unhealthy vapours, to perc contact with the skin (including of the feet) or eyes of the machine operator and those of other personnel and members of the public, as well as to water and ground contamination: perc emission to the workroom, seepage into the ground and sewer during operation and maintenance of the water separator; perc emission resulting from operation, cleaning and maintenance of the distilling installation.
|
Published |
2008-10 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 8230-3:2008 |
Safety requirements for dry-cleaning machines — Part 3: Machines using combustible solvents |
ISO 8230-3:2008 specifies safety requirements for dry-cleaning machines that use a combustible solvent (CS) as their cleaning medium.
It is applicable to such dry-cleaning machines, within the scope of ISO 8230-1, when they are used as intended and under conditions of misuse that are reasonably foreseeable by the manufacturer.
ISO 8230-3:2008, in conjunction with ISO 8230-1, deals with all significant hazards, significant hazardous situations and significant hazardous events that have been identified as being significant to the types of machines covered by this part of ISO 8230 and which require specific action by the designer or manufacturer to eliminate or reduce the risk.
It deals with the following significant hazards specific to the use of CS: hazards related to the entire dry-cleaning machine (electrical hazards, explosion hazards); hazards relating to the machine and tumblers (combustible solvent emission, explosion hazards during the cleaning phase, explosion hazards during the drying phase); hazards relating to the distilling equipment (combustible solvent emission, explosion hazards).
|
Published |
2008-10 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 8230:1997 |
Safety requirements for dry-cleaning machines using perchloroethylene |
|
Withdrawn |
1997-12 |
Edition : 1 |
Number of pages : 25 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 8232:1988 |
Closed-circuit dry-cleaning machines — Defining and checking of machine characteristics |
Provides suitable methods of checking the solvent consumption, the efficiency of solvent recovery during drying, and the solvent concentrations in the atmosphere surrounding the cited machines. Safety requirements concerning the industrial use of these machines are not included.
|
Published |
1988-11 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 9398-1:1993 |
Specifications for industrial laundry machines — Definitions and testing of capacity and consumption characteristics — Part 1: Flatwork ironing machines |
Defines the characteristics and gives the usual test methods for these characteristics with regard to the capacity, the power and water consumptions, and the hourly productivity. Does not cover safety requirements. Is used for reference in the drafting of purchasing orders for flatwork ironing machines.
|
Withdrawn |
1993-02 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 9398-1:2003 |
Specifications for industrial laundry machines — Definitions and testing of capacity and consumption characteristics — Part 1: Flatwork ironing machines |
ISO 9398-1:2002 defines the characteristics of flatwork ironing machines and gives the usual test methods for determining these characteristics with regard to machine capacity, power consumption and hourly productivity. It is applicable for use as a reference in the drafting of purchasing orders for flatwork ironing machines having a contact surface area greater than 0,25 m2. It does not cover safety requirements (see ISO 10472-5).
|
Published |
2003-01 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 4210-9:2023 |
Cycles — Safety requirements for bicycles — Part 9: Saddles and seat-post test methods |
This document specifies saddle and seat-post test methods for ISO 4210‑2.
|
Published |
2023-01 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
43.150
Cycles
|
| ISO 9398-2:1993 |
Specifications for industrial laundry machines — Definitions and testing of capacity and consumption characteristics — Part 2: Batch drying tumblers |
Defines the characteristics and gives the usual test methods for these characteristics with regard to the capacity, the power and water consumptions, and the hourly productivity. Does not cover safety requirements. Is used for reference in the drafting of purchasing orders for batch drying tumblers whose nominal capacity is at least 7 kg.
|
Withdrawn |
1993-02 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 9398-2:2003 |
Specifications for industrial laundry machines — Definitions and testing of capacity and consumption characteristics — Part 2: Batch drying tumblers |
ISO 9398-2:2002 defines the characteristics of batch drying tumblers and gives the usual test methods for these characteristics with regard to machine capacity, power consumption and productivity. It is applicable for use as a reference in the drafting of purchasing orders for batch drying tumblers whose net usable cage volume is greater than 160 dm3 (litres). It does not cover safety requirements (see ISO 10472-4).
|
Published |
2003-01 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 9398-3:1993 |
Specifications for industrial laundry machines — Definitions and testing of capacity and consumption characteristics — Part 3: Washing tunnels |
Defines the characteristics and gives the usual test methods for power and water consumption and the hourly productivity. Does not cover safety requirements. Is used for reference in the drafting of purchasing orders for washing tunnels.
|
Withdrawn |
1993-02 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 9398-3:2003 |
Specifications for industrial laundry machines — Definitions and testing of capacity and consumption characteristics — Part 3: Washing tunnels |
ISO 9398-3:2002 defines the characteristics of washing tunnels and gives the usual test methods for determining machine power consumption and hourly productivity. It is applicable for use as a reference in the drafting of purchasing orders for washing tunnels. It does not cover safety requirements (see ISO 10472-3).
|
Published |
2003-01 |
Edition : 2 |
Number of pages : 5 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 9398-4:1993 |
Specifications for industrial laundry machines — Definitions and testing of capacity and consumption characteristics — Part 4: Washer-extractors |
Defines the characteristics and gives the usual test methods for these characteristics with regard to the capacity, the power and water consumptions, and the hourly productivity. Does not cover safety requirements. Is used for reference in the drafting of purchasing orders for washer-extractors whose nominal capacity is at least 7 kg.
|
Withdrawn |
1993-02 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 9398-4:2003 |
Specifications for industrial laundry machines — Definitions and testing of capacity and consumption characteristics — Part 4: Washer-extractors |
ISO 9398-4:2002 defines the characteristics of washer-extractors and gives the usual test methods for these characteristics with regard to machine capacity, power and water consumption, and hourly productivity. It is applicable for use as a reference in the drafting of purchasing orders for washer-extractors whose net usable cage volume is greater than 60 dm (litres). It does not cover safety requirements (see ISO 10472-2).
|
Published |
2003-01 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 10472-1:1997 |
Safety requirements for industrial laundry machinery — Part 1: Common requirements |
|
Published |
1997-12 |
Edition : 1 |
Number of pages : 22 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 10472-2:1997 |
Safety requirements for industrial laundry machinery — Part 2: Washing machines and washer-extractors |
|
Published |
1997-12 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 10472-3:1997 |
Safety requirements for industrial laundry machinery — Part 3: Washing tunnel lines including component machines |
|
Published |
1997-12 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 10472-4:1997 |
Safety requirements for industrial laundry machinery — Part 4: Air dryers |
|
Published |
1997-12 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 10472-5:1997 |
Safety requirements for industrial laundry machinery — Part 5: Flatwork ironers, feeders and folders |
|
Published |
1997-12 |
Edition : 1 |
Number of pages : 19 |
Technical Committee |
97.060
Laundry appliances
|
| ISO 10472-6:1997 |
Safety requirements for industrial laundry machinery — Part 6: Ironing and fusing presses |
|
Published |
1997-12 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
97.060
Laundry appliances
|