| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO/IEC 22954:2022 |
Information technology — Office equipment — Automated colour profile distribution |
This document specifies a method of automated colour profile distribution to large format inkjet printers.
This document applies to digital colour printers and their printer controllers for which ICC colour management is necessary or desired. This document also applies to the print settings profile providers.
The extent of automation covered includes the printer controller acquiring information about the overall situation, connecting to a print settings profile provider on the Internet, determining the best possible profile to download (if it exists), and downloading and installation of the profile.
This document covers general concepts and procedures and does not go into a level of detail necessary to establish syntactic or semantic interoperability. This document covers ICC version 4 output profiles as specified by ISO 15076-1, but does not cover device link profiles.
|
Published |
2022-05 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO 24487-1:2021 |
Graphic technology — Processless lithographic plates — Part 1: Evaluation methods for characteristics and performance |
This document applies to processless lithographic plates and specifies evaluation methods for lithographic plate characteristics, on-press development performance, usability and print image quality.
It specifies measurement conditions for materials and equipment and provides guidelines for the selection of suitable processless lithographic plates by a printing organization and requirements for comparative assessment tests.
The assessment of waterless lithographic plates is out of scope of this document.
|
Published |
2021-11 |
Edition : 1 |
Number of pages : 29 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/DIS 24487 |
Graphic technology — Processless lithographic plates — Evaluation methods for characteristics and performance |
This document applies to processless lithographic plates and specifies evaluation methods for lithographic plate characteristics, on-press development performance, usability and print image quality.
It specifies measurement conditions for materials and equipment and provides guidelines for the selection of suitable processless lithographic plates by a printing organization and requirements for comparative assessment tests.
The assessment of waterless lithographic plates is out of scope of this document.
|
Under development |
|
Edition : 1 |
Number of pages : 37 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC TR 24705:2005 |
Information technology — Office machines — Machines for colour image reproduction — Method of specifying image reproduction of colour devices by digital and analog test charts |
ISO/IEC TR 24705:2005 deals with the colour reproduction properties of office devices, e. g. printers, scanners and monitors, which may depend on the device system, which includes e. g. the device properties and settings, the device driver, the file format, the computer operating system and the application software.
It presents a method to allow testing of the reproduction changes if one or several of the parameters are varied, such as the device properties or settings, the device driver, the file format, the computer operating system, the colour space, and the application software. This allows manufacturers and users to get a feeling or data about the influence of the different parameters on the reproduction.
|
Withdrawn |
2005-10 |
Edition : 1 |
Number of pages : 71 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24711:2006 |
Method for the determination of ink cartridge yield for colour inkjet printers and multi-function devices that contain printer components |
The scope of ISO/IEC 24711:2006 is limited to evaluation of ink cartridge page yield for ink-containing cartridges (i.e. integrated ink cartridges and ink cartridges without integrated print heads) for colour inkjet printers. It can also be applied to the printer component of any multifunctional device that has a digital input printing path, including multi-function devices that contain inkjet printer components. Both liquid and solid ink products can be tested using ISO/IEC 24711:2006.
|
Withdrawn |
2006-12 |
Edition : 1 |
Number of pages : 27 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24711:2007 |
Method for the determination of ink cartridge yield for colour inkjet printers and multi-function devices that contain printer components |
ISO/IEC 24711:2007 defines a method for testing and calculation of average yield measured in the number of standard pages for a colour inkjet cartridge and a specific printer printing in a semi-continuous mode under a defined set of conditions. It uses the test page suite defined in ISO/IEC 24712. ISO/IEC 24711:2007 can also be applied to the printer component of any multifunctional device that has a digital input-printing path (i.e. multi-function devices that contain printer components).
ISO/IEC 24711 is only intended for the measurement of colour inkjet cartridge yield. No other claims can be made from this testing regarding quality, reliability, etc.
|
Withdrawn |
2007-12 |
Edition : 2 |
Number of pages : 27 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24711:2007/Cor 1:2012 |
Method for the determination of ink cartridge yield for colour inkjet printers and multi-function devices that contain printer components — Technical Corrigendum 1 |
|
Withdrawn |
2012-09 |
Edition : 2 |
Number of pages : 1 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO 7174-2:1992 |
Furniture — Chairs — Determination of stability — Part 2: Chairs with tilting or reclining mechanisms when fully reclined, and rocking chairs |
Describes methods for determining the rearward stability of the chairs. Forward and sideward stability is determined by methods described in ISO 7174-1. The test results are only valid for the article tested.
|
Published |
1992-10 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
97.140
Furniture
|
| ISO/IEC 24711:2015 |
Method for the determination of ink cartridge yield for colour inkjet printers and multi-function devices that contain printer components |
The scope of ISO/IEC 24711:2015 is limited to evaluation of ink cartridge page yield for ink-containing cartridges (i.e. integrated ink cartridges and ink cartridges without integrated printheads) for colour inkjet print systems. ISO/IEC 24711:2015 can also be applied to the printer component of any multifunctional device that has a digital input printing path, including multi-function devices that contain inkjet printer components. Both liquid and solid ink products can be tested using ISO/IEC 24711:2015.
ISO/IEC 24711:2015 is only intended for the measurement of ink cartridge page yield when printing on plain paper. No other claims can be made from this testing regarding quality, reliability, etc.
It can be used to measure the yield of any cartridge that is used in a significant amount during the printing of the test suite defined in ISO/IEC 24712.
It is not for use with printers whose minimum printable size is equal to or greater than A3 or for printers designed or configured to print photos (for example, maximum printable size less than A4 or a printer configuration intended for photo-only printing). In addition, it only applies to drop-on-demand printing systems.
|
Withdrawn |
2015-11 |
Edition : 3 |
Number of pages : 28 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24711:2021 |
Information technology — Office equipment — Method for the determination of ink cartridge yield for colour inkjet printers and multi-function devices that contain printer components |
The scope of this document is limited to the evaluation of ink cartridge page yield for ink-containing cartridges (i.e. integrated ink cartridges and ink cartridges without integrated printheads) for colour inkjet print systems. This document can also be applied to the printer component of any multifunctional device that has a digital input printing path, including multi-function devices that contain inkjet printer components. Both liquid and solid ink products can be tested using this document.
This document is only intended for the measurement of ink cartridge page yield when printing on plain paper. No other claims can be made from this testing regarding quality, reliability, etc.
This document can be used to measure the yield of any cartridge that is used in a significant amount during the printing of the test page suite defined in ISO/IEC 24712.
This document is not for use with printers whose minimum printable size is equal to or greater than A3 or for printers designed or configured to print photos (for example, maximum printable size less than A4 or a printer configuration intended for photo-only printing). In addition, it only applies to drop-on-demand printing systems.
NOTE Integrated ink cartridges is a cartridge that includes at least: an ink containment part, an ink deposition mechanism and an ink transport part (see ISO/IEC 29142-1).
|
Published |
2021-01 |
Edition : 4 |
Number of pages : 30 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24712:2006 |
Colour test pages for measurement of office equipment consumable yield |
The scope of ISO/IEC 24712:2006 is to define colour test pages for the measurement of consumable yield. The test page suite includes four "customer" type documents and one "diagnostic" page that is used to determine end of ink or toner consumable life. These pages can be used for electro-photographic, inkjet printers and multi-function devices that have a digital printing path, i.e. an all-in-one electro-photographic machine that has digital printing capabilities.
ISO/IEC 24712:2006 provides a set of test pages in a common file format that would be used in the testing of consumable yield. The procedure for using these pages will be detailed in ISO/IEC 17978 and ISO/IEC 24711.
These pages are intended to represent the some of the types of documents that are used in the office and home. They are not intended to represent special applications such as photo printing.
|
Withdrawn |
2006-12 |
Edition : 1 |
Number of pages : 28 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24712:2007 |
Colour test pages for measurement of office equipment consumable yield |
ISO/IEC 24712:2007 defines colour test pages for the measurement of consumable yield. The test page suite includes four "customer" type documents and one "diagnostic" page that is used to determine end of ink or toner consumable life. These pages can be used for electro-photographic, inkjet printers and multi-function devices that have a digital printing path, i.e. an all-in-one electro-photographic machine that has digital printing capabilities.
ISO/IEC 24712:2007 provides a set of test pages in a common file format that would be used in the testing of consumable yield. The procedure for using these pages is detailed in ISO/IEC 19798 and ISO/IEC 24711.
These pages are intended to represent some of the document types that are used in the office and home. They are not intended to represent special applications such as photo printing.
|
Published |
2007-12 |
Edition : 2 |
Number of pages : 28 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24734:2009 |
Information technology — Office equipment — Method for measuring digital printing productivity |
ISO/IEC 24734:2009 provides a method for measuring the productivity of digital printing devices with various office applications and print job characteristics.
It is applicable to digital printing devices, including single function printing and multi-function devices, regardless of print technology (e.g. inkjet, laser). Devices can be equipped with a range of paper feed and finishing options either directly connected to the computer system or via a network.
It is intended to be used for black and white (B&W) as well as colour digital printing devices.
It allows for the comparison of the productivity of machines operating in various available modes (simplex, duplex, size of substrates, etc.) and office applications when the test system environment, operating modes, and job mix for each machine are held identical.
ISO/IEC 24734:2009 includes test files, test setup procedure, test runtime procedure, and the reporting requirements for the digital printing productivity measurements. It is not intended to be used for devices which are not able to print on a media size of A4/8.5”x11” or for devices which are not able to collate multiple copies of a print.
|
Withdrawn |
2009-03 |
Edition : 1 |
Number of pages : 44 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24734:2014 |
Information technology — Office equipment — Method for measuring digital printing productivity |
ISO/IEC 24734:2014 specifies a method for measuring the productivity of digital printing devices with various office applications and print job characteristics. It is applicable to digital printing devices, including single-function and multi-function devices, regardless of print technology (e.g. inkjet, laser). Devices can be equipped with a range of paper feed and finishing options either directly connected to the computer system or via a network. It is intended to be used for black and white (B&W) as well as colour digital printing devices. It allows for the comparison of the productivity of machines operating in various available modes (simplex, duplex, size of substrates, etc.) and office applications when the test system environment, operating modes, and job mix for each machine are held identical. ISO/IEC 24734:2014 includes test files, test setup procedure, test runtime procedure, and the reporting requirements for the digital printing productivity measurements.
ISO/IEC 24734:2014 is not intended to be used for devices which are not able to print on a media size of A4/8.5"x11" or for devices, which are not able to collate multiple copies of a print.
ISO/IEC 24734:2014 is not intended to replace a manufacturer's rated speeds.
The productivity of a digital printing device depends on factors other than the printing device itself. These include, but are not limited to, computer manufacturer and model, central processor type and speed, RAM and hard disk memory capacity and speed, software driver, version of the application being used, operating system, and the type and speed of the communication path from computer to printing device, etc. Because of this, in order to make useful and accurate direct comparisons of printing productivity with ISO/IEC 24734:2014, the same computer system hardware and software have to be used for measuring the printing devices, if, for the purpose of being directly compared one to another. For every printing productivity measurement, the basic specifications of the computer hardware and software have to be included with the results of the printing productivity measurement.
|
Withdrawn |
2014-07 |
Edition : 2 |
Number of pages : 50 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24734:2014/Cor 1:2016 |
Information technology — Office equipment — Method for measuring digital printing productivity — Technical Corrigendum 1 |
|
Withdrawn |
2016-08 |
Edition : 2 |
Number of pages : 1 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24734:2021 |
Information technology — Office equipment — Method for measuring digital printing productivity |
This document specifies a method for measuring the digital printing productivity of digital printing devices with various office applications and print job characteristics. This document is applicable to digital printing devices, including single-function and multi-function devices, regardless of print technology (e.g. inkjet, laser). Devices can be equipped with a range of paper feed and finishing options either directly connected to the computer system or via a network. It is intended to be used for black and white (B&W) as well as colour digital printing devices. It allows for the comparison of the productivity of machines operating in various available modes (simplex, duplex, size of substrates, etc.) and office applications when the test system environment, operating modes, and job mix for each machine are held identical. This document includes test files, test setup procedure, test runtime procedure, and the reporting requirements for the digital printing productivity measurements.
This document is not intended to be used for devices which are not able to print on a media size of A4/8,5” × 11” or for devices which are not able to collate multiple copies of a print.
This document is not intended to replace manufacturer's rated speeds.
|
Published |
2021-04 |
Edition : 3 |
Number of pages : 61 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24735:2009 |
Information technology — Office equipment — Method for measuring digital copying productivity |
ISO/IEC 24735:2009 provides a method for measuring digital copying productivity of digital copying devices and multifunctional devices with various copying modes.
It is applicable to digital copying devices and multifunctional devices equipped with automatic document feeder and collating function.
It is intended to be used for black and white (B&W) as well as colour digital copying devices and multifunctional devices of any underlying marking technology.
It allows comparison of the throughput copying rates for a machine operated in various available operating modes (simplex, duplex, size of substrates, 2-up, etc) and various available digital image processing configurations.
ISO/IEC 24735:2009 includes test files, test setup procedure, test procedure, and the reporting requirements for the digital copying productivity measurements.
|
Withdrawn |
2009-03 |
Edition : 1 |
Number of pages : 30 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24735:2009/Cor 1:2009 |
Information technology — Office equipment — Method for measuring digital copying productivity — Technical Corrigendum 1 |
|
Withdrawn |
2009-06 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24735:2012 |
Information technology — Office equipment — Method for measuring digital copying productivity |
ISO/IEC 24735:2012 specifies a method for measuring the "productivity" of digital copying devices and multifunctional devices with various copying modes. It is applicable to digital copying devices and multifunctional devices equipped with automatic document feeder and collating function.
|
Withdrawn |
2012-06 |
Edition : 2 |
Number of pages : 30 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24735:2021 |
Information technology — Office equipment — Method for measuring digital copying productivity |
This document specifies a method for measuring the digital copying productivity of digital copying devices and multifunctional devices with various copying modes. It is applicable to digital copying devices and multifunctional devices equipped with automatic document feeder (ADF) and collating function. This document is intended to be used for black and white (B&W) as well as colour digital copying devices and multifunctional devices of any underlying marking technology. It allows comparison of the throughput copying rates for a machine operated in various available operating modes (simplex, duplex, size of substrates, 2-up, etc.) and various available digital image processing configurations. This document includes test files, test setup procedures, test procedures, and reporting requirements for digital copying productivity measurements.
This document is not intended to be used for devices which are not able to copy on a media size of A4/8,5” × 11”, devices that do not have an ADF, or devices which are not able to collate multiple copies of original prints from a test set.
This document is not intended to replace manufacturer's rated speeds.
|
Published |
2021-04 |
Edition : 3 |
Number of pages : 40 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24790:2017 |
Information technology — Office equipment — Measurement of image quality attributes for hardcopy output — Monochrome text and graphic images |
ISO/IEC 24790:2017 specifies device-independent image quality attributes, measurement methods and analytical procedures to describe the quality of output images from hardcopy devices. This document is applicable to human-readable monochrome documents produced from printers and copiers.
The attributes, methods and procedures rely on measurable properties of printed text and graphic images. Special targets or reference images are not required, but image elements are useful for adequate measurements only if they meet some minimal requirements, e.g. on size or number present. This document is not applicable to images on media other than hardcopy (e.g. images on a visual display) or to images that are intended to be machine readable only (e.g. bar codes).
|
Published |
2017-02 |
Edition : 1 |
Number of pages : 65 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC TS 24790:2012 |
Information technology — Office equipment — Measurement of image quality attributes for hardcopy output — Monochrome text and graphic images |
ISO/IEC TS 24790:2012 specifies device-independent image quality attributes, measurement methods, and analytical procedures to describe the quality of output images from hardcopy devices. It is applicable to human-readable monochrome documents produced from printers and copiers.
The attributes, methods and procedures rely on measurable properties of printed text and graphic images. Special targets or reference images are not required, but image elements must meet some minimal requirements, e.g. on size or number present, in order to be useful for adequate measurements.
ISO/IEC TS 24790:2012 is not applicable to images on media other than hardcopy (e.g. images on a VDT) or to images that are intended to be machine readable only (e.g. bar codes).
|
Withdrawn |
2012-08 |
Edition : 1 |
Number of pages : 44 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 24790:2017/Amd 1:2022 |
Information technology — Office equipment — Measurement of image quality attributes for hardcopy output — Monochrome text and graphic images — Amendment 1 |
|
Published |
2022-10 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 28360-1:2018 |
Information technology — Office equipment — Determination of chemical emission rates from electronic equipment — Part 1: Using-consumables |
This document (all parts) specifies methods to determine chemical emission rates of analyte from ICT & CE equipment during intended operation in an Emission Test Chamber (ETC).
This document (all parts) includes specific methods for equipment using consumables, such as printers, and equipment not using consumables, such as monitors and PC's.
Part 1 specifies the methods to determine chemical emission rates of analyte from electronic equipment using consumables.
The methods comprise preparation, sampling (or monitoring) in a controlled ETC, storage and analysis, calculation and reporting of emission rates.
Emission rates from EUT may also be determined according to additional requirements identified by "RAL‑UZ 205 Option".
Annex A specifies monochrome and colour print patterns for use in the operating phase of EUT using consumables.
The operational readiness of AMS is confirmed according to Annex B.
Calculations use the generalised model and approximations thereof as developed in Annex C.
The emission rates determined with this method may be used to compare equipment in the same class.
Predictions of "real indoor" concentrations from the determined emission rates are outside the scope of this document.
|
Withdrawn |
2018-09 |
Edition : 1 |
Number of pages : 40 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 28360-1:2021 |
Information technology — Determination of chemical emission rates from electronic equipment — Part 1: Using consumables |
This document (all parts) specifies methods to determine chemical emission rates of analytes from ICT & CE equipment during intended operation in an Emission Test Chamber (ETC).
This document (all parts) includes specific methods for equipment using consumables, such as printers, and equipment not using consumables, such as monitors and PC’s.
Part 1 specifies the methods to determine the emission rates of VOC and carbonyl compounds, ozone, particulate matter, fine particles (FP) and ultra-fine particles (UFP) from electronic equipment using consumables.
The methods comprise preparation, sampling (or monitoring) in a controlled ETC, storage and analysis, calculation and reporting of emission rates.
Part 1 has two different methods for the determination of emission rates of VOC and carbonyl compounds. The two methods use two different emission models, the quasi-equilibrium model (QEM) and the constant emission model (CEM) respectively, to determine the emission rates of VOC and carbonyl compounds during the pre-operating phase.
The quasi-equilibrium model method has been developed with hard copy devices for office or home use in mind whose energy-saving modes automatically activate during most intervals between operations. The calculation of emission rates during the pre-operating phase is based on the quasi-equilibrium assumption as shown in Annex C.
The emission rates determined with this method can be used to compare equipment in the same class since test procedures are specified more narrowly than the other method (CEM).
The constant emission model (CEM) has been developed for hard copy devices whose energy-saving modes have such a negligible effect on the determination of emission rates of VOC and carbonyl compounds that the generalised constant emission model shown in Annex D can be used for the determination of their emission rates during the pre-operating phase. This method presents more flexible test procedures than the QEM. Due to such features of this method, it may be used for hard copy devices whose idling mode usually lasts throughout intervals between operations, such as large hard copy devices used professionally. It may also be used for various equipment having different functions and structure for its intended use and the determination of carbonyl compounds requiring longer sampling duration due to a lack of sensitivity.
Annex A specifies monochrome and colour print patterns for use in the operating phase of EUT using consumables.
The operational readiness of AMS is confirmed according to Annex B.
Predictions of “real indoor” concentrations from the determined emission rates are outside the scope of this document.
|
Published |
2021-10 |
Edition : 2 |
Number of pages : 54 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 29142-1:2013 |
Information technology — Print cartridge characterization — Part 1: General: terms, symbols, notations and cartridge characterization framework |
ISO/IEC 29142-1:2013 establishes terms, symbols, notations and a framework for characterizing toner and ink cartridges used in printing devices that have a digital input printing path, including multi-function devices. It is intended for equipment used in office environments.
It primarily provides a foundation for measuring, evaluating, or specifying characteristics of such toner and ink cartridges.
The terms, symbols, notations and framework established in ISO/IEC 29142-1:2013 can be applied to such cartridges.
The characterizations associated with the terms, symbols, notations, and framework established in ISO/IEC 29142-1:2013 are specified throughout the ISO/IEC 29142 series.
|
Withdrawn |
2013-04 |
Edition : 1 |
Number of pages : 29 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 28360-2:2018 |
Information technology — Office equipment — Determination of chemical emission rates from electronic equipment — Part 2: Not using-consumables |
This Standard (all parts) specifies methods to determine chemical emission rates of analyte from ICT & CE equipment during intended operation in an Emission Test Chamber (ETC).
This Standard (all parts) includes specific methods for equipment using consumables, such as printers, and equipment not using consumables, such as monitors and PC's.
Part 2 specifies the methods to determine chemical emission rates of analyte from electronic equipment not using consumables.
The methods comprise preparation, sampling (or monitoring) in a controlled ETC, storage and analysis, calculation and reporting of emission rates.
Examples of EUT that do not use consumables are:
— Monitors and TV sets (CRT, Plasma, LCD, Rear projector, Beamer).
— Video (VCR, DVD Player/Recorder, Camcorder).
— SAT Receiver (Set-Top Box).
— Audio units (CD Player/Recorder, Home theatre Systems, Audio Home Systems, Micro-/Mini, Midi Systems, Amplifier, Receiver).
— Portable Audio (CD Player, MP 3 Player, Radio recorder, Clock radio, etc.).
— Computer (desktop, tower, server), portable computers (Notebooks).
The emission rates determined with this method may be used to compare equipment in the same class.
Predictions of "real indoor" concentrations from the determined emission rates are outside the scope of this Standard.
|
Published |
2018-09 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 28360:2007 |
Information technology — Office equipment — Determination of chemical emission rates from electronic equipment |
ISO/IEC 28360:2007 specifies methods to determine chemical emission rates of analyte from information and communication technology and consumer electronics equipment during intended operation in an Emission Test Chamber (ETC).
The methods comprise preparation, sampling (or monitoring) in a controlled ETC, storage and analysis, calculation and reporting of emission rates.
ISO/IEC 28360:2007 includes specific methods for equipment using consumables, such as printers, and equipment not using consumables, such as monitors and PCs.
|
Withdrawn |
2007-09 |
Edition : 1 |
Number of pages : 30 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 28360:2007/Cor 1:2008 |
Information technology — Office equipment — Determination of chemical emission rates from electronic equipment — Technical Corrigendum 1 |
|
Withdrawn |
2008-01 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 28360:2012 |
Information technology — Office equipment — Determination of chemical emission rates from electronic equipment |
ISO/IEC 28360:2012 specifies methods to determine chemical emission rates of analyte from information and communication technology (ICT) and consumer electronics (CE) equipment during intended operation in an Emission Test Chamber (ETC).
The methods comprise preparation, sampling (or monitoring) in a controlled ETC, storage and analysis, calculation and reporting of emission rates.
ISO/IEC 28360:2012 includes specific methods for equipment using consumables, such as printers, and equipment not using consumables, such as monitors and PCs. It also specifies monochrome and colour print patterns for use in the operating phase of EUT using consumables (e.g. paper).
|
Withdrawn |
2012-02 |
Edition : 2 |
Number of pages : 45 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 28360:2015 |
Information technology — Office equipment — Determination of chemical emission rates from electronic equipment |
ISO/IEC 28360:2015 specifies methods to determine chemical emission rates of Analyte from ICT & CE equipment during intended operation in an Emission Test Chamber (ETC).
The methods comprise preparation, sampling (or monitoring) in a controlled ETC, storage and analysis, calculation and reporting of emission rates.
This International Standard includes specific methods for equipment using consumables, such as printers, and equipment not using consumables, such as monitors and PC's. Annex A specifies monochrome and colour print patterns for use in the operating phase of EUT using consumables (e.g. paper).
Examples of EUT that do not use consumables are:
· Monitors and TV sets (CRT, Plasma, LCD, Rear projector, Beamer).
· Video (VCR, DVD Player/Recorder, Camcorder).
· SAT Receiver (Set-Top Box).
· Audio units (CD Player/Recorder, Home theatre Systems, Audio Home Systems, Micro-/Mini, Midi Systems, Amplifier, Receiver).
· Portable Audio (CD Player, MP 3 Player, Radio recorder, Clock radio etc).
· Computer (desktop, tower, server), portable computers (Notebooks).
Emission rates from EUT using consumables may also be determined according to additional requirements identified by "RAL-UZ 171 Option".
Calculations use the generalised model and approximations thereof as developed in Annex C.
The emission rates determined with this method may be used to compare equipment in the same class.
Predictions of "real indoor" concentrations from the determined emission rates are outside the scope of this International Standard.
|
Withdrawn |
2015-09 |
Edition : 3 |
Number of pages : 45 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 28360:2015/Cor 1:2016 |
Information technology — Office equipment — Determination of chemical emission rates from electronic equipment — Technical Corrigendum 1 |
|
Withdrawn |
2016-02 |
Edition : 3 |
Number of pages : 5 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 29102:2011 |
Information technology — Office equipment — Method for the determination of ink cartridge photo yield for colour printing with inkjet printers and multi-function devices that contain inkjet printer components |
ISO/IEC 29102:2011 provides a method to determine the ink cartridge photo yield of ink-containing cartridges (i.e. integrated ink cartridges and ink cartridges without integrated print heads) for colour photo printing with colour inkjet printers and multi-function devices that contain inkjet printer components. Ink cartridge yields determined on one printer model, paper and cartridge configuration are not applicable to another printer model or cartridge configuration even if the ink jet cartridges used in testing are the same.
It prescribes the following:
the test method that manufacturers, test labs, etc. use to determine ink cartridge photo yield;
the method for determination of declared photo yield values from the test results; and
the appropriate method of describing the photo yield of cartridges in documentation supplied to the consumer by the manufacturer.
|
Withdrawn |
2011-08 |
Edition : 1 |
Number of pages : 27 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 29102:2015 |
Information technology — Office equipment — Method for the determination of ink cartridge photo yield for colour printing with inkjet printers and multi-function devices that contain inkjet printer components |
ISO/IEC 29102:2015 is to provide a method to determine the ink cartridge photo yield of ink-containing cartridges (i.e. integrated ink cartridges and ink cartridges without integrated printheads) for colour photo printing with colour inkjet printers and multifunction devices that contain inkjet printer components. In the case where a cartridge set can be used in multiple printer models, only one yield test needs to be performed as long as the difference between printer models does not impact yield.
NOTE A cartridge supplier may choose to use more than one market identifier for a single physical cartridge. In this case only one yield test is required as long as there are no differences in the cartridges other than market identifiers.
ISO/IEC 29102:2015 prescribes the following:
- the test method that manufacturers, test laboratories, etc. use to determine ink cartridge photo yield;
- the method for determination of declared photo yield values from the test results; and
- the appropriate method of describing the photo yield of cartridges in documentation supplied to the consumer by the manufacturer.
ISO/IEC 29102:2015 is only intended for the determination of ink cartridge photo yield. No other claims can be made from this testing regarding quality, reliability, etc.
ISO/IEC 29102:2015 can be used to determine the yield of any cartridge that is used during the printing of the photo test file defined in ISO/IEC 29103.
ISO/IEC 29102:2015 is not for use with printers whose minimum printable size is equal to or greater than A3. This International Standard is not intended to measure the yield of photo printing on paper size larger than 4×6, L or A6. In addition, this International Standard is not for use with industrial printers or point of sale printers. It only applies to desktop printing systems.
|
Published |
2015-08 |
Edition : 2 |
Number of pages : 26 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC DIS 29102 |
Information technology — Office equipment — Method for the determination of ink cartridge photo yield for colour printing with inkjet printers and multi-function devices that contain inkjet printer components |
ISO/IEC 29102:2015 is to provide a method to determine the ink cartridge photo yield of ink-containing cartridges (i.e. integrated ink cartridges and ink cartridges without integrated printheads) for colour photo printing with colour inkjet printers and multifunction devices that contain inkjet printer components. In the case where a cartridge set can be used in multiple printer models, only one yield test needs to be performed as long as the difference between printer models does not impact yield.
NOTE A cartridge supplier may choose to use more than one market identifier for a single physical cartridge. In this case only one yield test is required as long as there are no differences in the cartridges other than market identifiers.
ISO/IEC 29102:2015 prescribes the following:
- the test method that manufacturers, test laboratories, etc. use to determine ink cartridge photo yield;
- the method for determination of declared photo yield values from the test results; and
- the appropriate method of describing the photo yield of cartridges in documentation supplied to the consumer by the manufacturer.
ISO/IEC 29102:2015 is only intended for the determination of ink cartridge photo yield. No other claims can be made from this testing regarding quality, reliability, etc.
ISO/IEC 29102:2015 can be used to determine the yield of any cartridge that is used during the printing of the photo test file defined in ISO/IEC 29103.
ISO/IEC 29102:2015 is not for use with printers whose minimum printable size is equal to or greater than A3. This International Standard is not intended to measure the yield of photo printing on paper size larger than 4×6, L or A6. In addition, this International Standard is not for use with industrial printers or point of sale printers. It only applies to desktop printing systems.
|
Under development |
|
Edition : 3 |
Number of pages : 27 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 29103:2011 |
Information technology — Office equipment — Colour photo test pages for measurement of ink cartridge yield for colour photo printing |
ISO/IEC 29103:2011 defines a set of test images in a common file format, JPEG, that are used in the testing of cartridge yield for printing of photographs. The defined documents are used in ISO/IEC 29102 to determine the photo yield of cartridges in an inkjet-based printing system.
|
Published |
2011-05 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 29112:2018 |
Information technology — Office equipment — Test pages and methods for measuring monochrome printer resolution |
This document defines methods for the objective measurement of the print quality characteristics that contribute to the perceived resolution of reflection mode monochrome printed pages produced by digital electro-photographic printers. The measurement methods of this document are derived from several existing techniques for the assessment of an imaging system's resolution characteristics. Each of these measurement methods is intended for the engineering evaluation of a printing system's perceived resolution and is not intended to be used for purposes of advertising claims.
The methods of this document are applicable only to monochrome prints produced in reflection mode by electro-photographic printing technology. This document is intended for monochrome printers utilizing PostScript®[1] interpreters capable of accepting PostScript and encapsulated PostScript (EPS) jobs.
[1] PostScript® and Encapsulated PostScript® are registered trademarks for freely usable page description formats controlled and defined by Adobe Systems Incorporated. This information is given for the convenience of users of this document and does not constitute an endorsement by ISO/IEC.
|
Published |
2018-11 |
Edition : 1 |
Number of pages : 87 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC TS 29112:2012 |
Information technology — Office equipment — Test charts and methods for measuring monochrome printer resolution |
ISO/IEC 29112 defines methods for the objective measurement of the print quality characteristics that contribute to the perceived resolution of reflection mode monochrome printed pages produced by digital electro-photographic printers.
The measurement methods used in ISO/IEC 29112 are derived from several existing techniques for the assessment of an imaging system's resolution characteristics. Each of these measurement methods is intended for the engineering evaluation of a printing system's perceived resolution and not for purposes of advertising claims.
The methods are applicable only to monochrome prints produced in reflection mode by electro-photographic printing technology.
ISO/IEC 29112 is intended for monochrome printers utilizing postscript interpreters capable of accepting postscript and encapsulated postscript (EPS) jobs.
|
Withdrawn |
2012-08 |
Edition : 1 |
Number of pages : 33 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/R 499:1966 |
Paper — Internal diameters of cores of reels |
|
Withdrawn |
1966-09 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
85.080
Paper products
|
| ISO 7175-1:1997 |
Children's cots and folding cots for domestic use — Part 1: Safety requirements |
|
Withdrawn |
1997-08 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
97.140
Furniture
|
| ISO/IEC 29142-1:2021 |
Information technology — Print cartridge characterization — Part 1: General: terms, symbols, notations and cartridge characterization framework |
This document establishes terms, symbols, notations and a framework for characterizing toner and ink cartridges used in printing devices that have a digital input printing path, including multi-function devices. This document is intended for equipment used in office environments.
It primarily provides a foundation for measuring, evaluating, or specifying characteristics of such toner and ink cartridges.
The terms, symbols, notations and framework established herein can be applied to such cartridges.
The characterizations associated with the terms, symbols, notations, and framework established herein are specified throughout the ISO/IEC 29142 series.
|
Published |
2021-08 |
Edition : 2 |
Number of pages : 30 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 29142-2:2013 |
Information technology — Print cartridge characterization — Part 2: Cartridge characterization data reporting |
ISO/IEC 29142-2:2013 establishes the product and package labelling, and related reporting provisions for toner and ink cartridges used in printing devices that have a digital input printing path, including multi-function devices. It is intended for equipment used in office environments.
ISO/IEC 29142-2:2013 defines the information requirements for the cartridge characterization documentation on packaging and cartridges, and in reports.
|
Published |
2013-04 |
Edition : 1 |
Number of pages : 15 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 29142-3:2013 |
Information technology — Print cartridge characterization — Part 3: Environment |
ISO/IEC 29142-3:2013 describes the principles and framework for environmental assessment of ink and toner cartridges used in printing devices that have a digital input printing path, including multi-function devices, including:
a) the goals and definitions related to environmental responsibility;
b) guidance to determine the relative benefits of reuse, recycling, recovery, and reduction techniques;
c) identification and prioritization of environmental attributes according to each phase of the cartridge life-cycle;
d) criteria for establishing environmentally sustainable practices.
ISO/IEC 29142-3:2013 establishes foundational terms, definitions, attributes, and test methods for cartridge environmental standards, environmental labels, and green procurement criteria.
ISO/IEC 29142-3:2013 standardizes treatment of environmental interactions and impacts throughout the cartridge life-cycle, and promotes harmonization of environmental standards, environmental labels, and green procurement criteria pertaining to ink and toner cartridges, thereby reducing impact on the environment and informing and benefiting the cartridge customer.
ISO/IEC 29142-3:2013 establishes environmental terms, definitions, attributes and test methods in accordance with the terms, symbols, notations and framework of ISO/IEC 29142-1 and ISO Guide 64.
|
Published |
2013-03 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 29183:2010 |
Information technology — Office equipment — Method for measuring digital copying productivity of a single one-sided original |
ISO/IEC 29183:2010 specifies a method for measuring productivity of digital copying devices and multifunctional devices with various copying modes and a single one-sided original. It is applicable to digital copying devices and multifunctional devices. It is intended to be used for black-and-white and colour digital copying devices and multifunctional devices of any underlying marking technology. ISO/IEC 29183:2010 includes instructions for the creation of test charts, test setup procedure, test procedure, and the reporting requirements for the digital copying productivity measurements.
ISO/IEC 29183:2010 is not intended to replace manufacturer's rated speeds.
|
Withdrawn |
2010-12 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC 29183:2021 |
Information technology — Office equipment — Method for measuring digital copying productivity for a single one-sided original |
This document specifies a method for measuring productivity of digital copying devices and multifunctional devices with various copying modes and a single one-sided original. The document is applicable to digital copying devices and multifunctional devices. The document is intended to be used for black and white (B&W) as well as colour digital copying devices and multifunctional devices of any underlying marking technology. This document includes instructions for the creation of test charts, test setup procedure, test procedure, and the reporting requirements for the digital copying productivity measurements.
This document is not intended to replace manufacturer's rated speeds.
|
Published |
2021-04 |
Edition : 2 |
Number of pages : 31 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO/IEC TR 29186:2012 |
Information technology — Office equipment — Test method of colour gamut mapping algorithm for office colour softcopy and hardcopy |
ISO/IEC TR 29186:2012 is a supplement to CIE 156:2004, applicable for use in evaluating the colour gamut mapping algorithms of office colour softcopy and hardcopy equipment. ISO/IEC TR 29186:2012 defines test charts, test chart image processing workflow, media, viewing conditions, measurements, colour spaces and experimental methods, suitable for use with office equipment, which either do not exist in CIE 156:2004 or are different from CIE 156:2004. Colour softcopy may be displayed on monitors, incorporating display technologies such as CRT and LCD. Colour hardcopy may be produced by non-impact colour printers, including technologies such as ink jet and electro photography.
|
Published |
2012-07 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
37.100.10
Reproduction equipment
|
| ISO 328:1974 |
Picture postcards and lettercards — Size |
Does not apply to illustrated lettercards. Picture postcards and lettercards shall be size A6.
|
Withdrawn |
1974-06 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
85.080
Paper products
|
| ISO 4211-2:1993 |
Furniture — Tests for surfaces — Part 2: Assessment of resistance to wet heat |
The principle of the method specified is to place a standard aluminium alloy block at a specified test temperature on a damp cloth in contact with the surface of the test panel (or on finished furniture), removing the block and damp cloth after a specified period of time, wiping the test area dry and leaving the test panel undisturbed for at least 16 h, then examining it under specified lighting conditions for signs of damage (discoloration, change in lustre, blistering or other defects). Applies to the hard surfaces of all finished furniture, regardless of material, except for finishes on leather and coated fabrics.
|
Withdrawn |
1993-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
97.140
Furniture
|
| ISO 4211-2:2013 |
Furniture — Tests for surface finishes — Part 2: Assessment of resistance to wet heat |
ISO 4211-2:2013 specifies a method for the assessment of the resistance to wet heat of all rigid furniture surfaces regardless of materials.
It does not apply to leather and textile surfaces.
|
Published |
2013-05 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
97.140
Furniture
|
| ISO 4211-3:1993 |
Furniture — Tests for surface finishes — Part 3: Assessment of resistance to dry heat |
The principle of the method specified is to place a standard aluminium alloy block at a specified test temperature on the surface of the test panel (or on finished furniture), removing the block after a specified period of time, wiping the test area dry and leaving the test panel undisturbed for at least 16 h, then examining it under specified lighting conditions for signs of damage (discoloration, change in lustre, blistering or other defects). Applies to the hard surfaces of all finished furniture, regardless of material, except for finishes on leather and coated fabrics.
|
Withdrawn |
1993-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
97.140
Furniture
|
| ISO 4211-3:2013 |
Furniture — Tests for surface finishes — Part 3: Assessment of resistance to dry heat |
ISO 4211-3:2013 specifies a method for the assessment of the resistance to dry heat of all rigid furniture surfaces regardless of materials.
It does not apply to leather and textile surfaces.
|
Published |
2013-05 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
97.140
Furniture
|
| ISO 4211-4:1988 |
Furniture — Tests for surfaces — Part 4: Assessment of resistance to impact |
The specified method is suitable for use either as a means of comparing different finishing systems or as a quality control test to ensure that a specified performance level is achieved or maintained. The tests are carried out on panels of the same materials and finished in the identical manner as the finished furniture of a size sufficient to meet the requirements of the test. The degree of damage to the test area is assessed by reference to a descriptive numerical rating code.
|
Published |
1988-07 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
97.140
Furniture
|
| ISO 4211-5:2021 |
Furniture — Tests for surface finishes — Part 5: Assessment of resistance to abrasion |
This document specifies a method for the assessment of the abrasion resistance of surfaces with foils, laminates, melamine faced boards, pigmented and transparent lacquers.
The test is intended to be carried out on an unused part of the finished furniture, but can be carried out on test panels of the same material, finished in an identical manner to the finished product, and of a size sufficient to meet the requirements of the test.
|
Published |
2021-10 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
97.140
Furniture
|
| ISO 4211:1979 |
Furniture — Assessment of surface resistance to cold liquids |
The specified method applies to surfaces of finished furniture or test panels of the same material and finished in the identical manner as the finished furniture with a size sufficient to meet the requirements of the test. The type and number of test liquids and the test periods can be selected from the tables in clause 5 and in the annex. The test results are assessed in terms of a descriptive numerical rating code.
|
Published |
1979-09 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
97.140
Furniture
|
| ISO 4769:2022 |
Hardware for furniture — Strength and durability of hinges and their components — Hinges pivoting on a vertical axis |
This document specifies test methods and test parameters for the strength and durability of all types of hinges pivoting on a vertical axis and their components for all fields of application.
With the exception of corrosion, ageing and the influence of heat and humidity are not included.
|
Published |
2022-11 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
97.140
Furniture
|
| ISO 5970:1979 |
Furniture — Chairs and tables for educational institutions — Functional sizes |
The specified dimensions are confined to those which derive from anthropometric data; compliance with them ensures that the furniture permits good seating postures. The seven sizes for seating and related tables based on a reference stature are given in tables 1 and 2, and the references to the dimensions are shown in figures 1 and 2. This standard does not include special requirements applicable to "special schools" and adjustable furniture.
|
Withdrawn |
1979-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
97.140
Furniture
|
| ISO/FDIS 6128 |
Laminated products made of bamboo strips for indoor furniture purposes — Requirements and test methods |
|
Under development |
|
Edition : 1 |
Number of pages : 7 |
Technical Committee |
97.140
Furniture
|
| ISO 7170:1993 |
Furniture — Storage units — Determination of strength and durability |
Describes test methods for determining the strength and durability (mainly regarding fatigue and wear) of storage units that are fully assembled and ready for use, including their movable and non-movable parts. Assessment of ageing and degradation is not included. The tests consist of the application of loads, forces and velocities simulating normal functional use as well as misuse to be expected and are designed to evaluate properties without regard to materials, design/construction or manufacturing processes. Does not specify requirements to be met.
|
Withdrawn |
1993-10 |
Edition : 1 |
Number of pages : 16 |
Technical Committee |
97.140
Furniture
|
| ISO 7170:2005 |
Furniture — Storage units — Determination of strength and durability |
ISO 7170:2005 specifies test methods for determining the strength and durability of storage units that are fully assembled and ready for use, including their movable and non-movable parts. The tests consist of the application, to various parts of the unit, of loads, forces and velocities simulating normal functional use, as well as misuse, that might reasonably be expected to occur.
The test results are only valid for the unit/component tested. These results may be used to represent the performance of production models provided that the tested model is representative of the production model. Tests carried out according to ISO 7170:2005 are intended to demonstrate the ability of the item to give satisfactory service in its intended environment. The tests have been developed for units/components that have not been in use. However, when properly justified, they may be used for fault investigation.
Assessment of ageing and degradation is not included.
|
Withdrawn |
2005-12 |
Edition : 2 |
Number of pages : 32 |
Technical Committee |
97.140
Furniture
|
| ISO 7170:2021 |
Furniture — Storage units — Test methods for the determination of strength, durability and stability |
This document specifies test methods for determining the strength, durability and stability of storage units, when fully assembled prior to use, including their movable and non-movable parts.
Acceptance criteria for the strength, durability and stability of the storage furniture is not specified by the test methods. Instead, suggested loads, cycles and forces are provided in Annex B, depending on the applicability of the furniture.
|
Published |
2021-09 |
Edition : 3 |
Number of pages : 59 |
Technical Committee |
97.140
Furniture
|
| ISO 7171:1988 |
Furniture — Storage units — Determination of stability |
The specified methods are applicable to free-standig storage furniture including cupboards, cabinets and bookshelves that are fully assembled and ready for use. Wall-mounted or otherwise built-in units are not covered. The test results are only valid for the article tested. When they are intended to be applied to other similar articles, the test specimen should be representative of the production model. Otherwise the test should be carried out as far as possible as described and the deviations from the test procedure reported.
|
Withdrawn |
1988-05 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
97.140
Furniture
|
| ISO 7171:2019 |
Furniture — Storage units — Test methods for the determination of stability |
This document specifies test methods for determining the stability of free-standing storage units that are fully assembled and ready for use.
The test results are only valid for the unit/component tested. These results can be used to represent the performance of production models provided that the tested model is representative of the production model.
This document specifies test methods only. It does not specify requirements for specific forces that the storage unit must withstand without overturning. It is intended that these be specified in a requirements document.
|
Withdrawn |
2019-02 |
Edition : 2 |
Number of pages : 19 |
Technical Committee |
97.140
Furniture
|
| ISO 7172:1988 |
Furniture — Tables — Determination of stability |
|
Published |
1988-05 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
97.140
Furniture
|
| ISO 7173:1989 |
Furniture — Chairs and stools — Determination of strength and durability |
Test methods are described for all types of chairs, easy chairs and stools except reclining or tilted chairs in the reclined or tilted position and chairs for specific fields of use. Assessment of ageing and degradation and tests for stuffing materials, upholstery fabrics or foam cushions are not included. The tests are designed to be applied to articles that are fully assembled and ready for use. Forces and dimensions therein are applicable to chairs and stools intended for adult persons.
|
Published |
1989-07 |
Edition : 1 |
Number of pages : 20 |
Technical Committee |
97.140
Furniture
|
| ISO/FDIS 7173 |
Furniture — Chairs and stools — Determination of strength and durability |
|
Under development |
|
Edition : 2 |
|
Technical Committee |
97.140
Furniture
;
97.140
Furniture
|
| ISO 7174-1:1988 |
Furniture — Chairs — Determination of stability — Part 1: Upright chairs and stools |
The calculative and experimental methods are not applicable to settees and other multiple seating, nor to swivelling or rocking chairs. They include chairs with tilting, reclining and adjustable back-angle mechanisms only when used as upright chairs. Part 2 of ISO 7174 deals with the stability of such chairs when fully reclined. The annex does form part of ISO 7174-1. The chart gives suggested minimum overturning forces applicable to all types of adult chairs according to their loaded seat heights.
|
Published |
1988-07 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
97.140
Furniture
|
| ISO 7175-1:2019 |
Furniture — Children's cots and folding cots for domestic use — Part 1: Safety requirements |
This document specifies requirements for children's cots and folding cots for domestic use with an internal length of between 900 mm and 1 400 mm.
This document applies to cots that are fully assembled and ready for use.
NOTE It is possible that additional requirements be applied for cots that can be converted into other items (e.g. changing units, playpens).
This document does not apply to carry cots, cribs and cradles for which separate International Standards exist.
|
Published |
2019-01 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
97.140
Furniture
|
| ISO 7175-2:1988 |
Furniture — Children's cots — Safety requirements and testing — Part 2: Test methods |
|
Withdrawn |
1988-07 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
97.140
Furniture
;
97.190
Equipment for children
|
| ISO 7175-2:1997 |
Children's cots and folding cots for domestic use — Part 2: Test methods |
|
Withdrawn |
1997-08 |
Edition : 2 |
Number of pages : 13 |
Technical Committee |
97.140
Furniture
|
| ISO 7175-2:2019 |
Furniture — Children's cots and folding cots for domestic use — Part 2: Test methods |
This document specifies test methods to assess the safety of children's cots and folding cots for domestic use with an internal length of between 900 mm and 1 400 mm.
|
Published |
2019-01 |
Edition : 3 |
Number of pages : 28 |
Technical Committee |
97.140
Furniture
|
| ISO 7617-1:1988 |
Plastics-coated fabrics for upholstery — Part 1: Specification for PVC-coated knitted fabrics |
|
Withdrawn |
1988-07 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
83.140
Rubber and plastics products
;
97.140
Furniture
|
| ISO 7617-1:1994 |
Plastics-coated fabrics for upholstery — Part 1: Specification for PVC-coated knitted fabrics |
Cancels and replaces the first edition (1988). Specifies requirements for coated fabrics for upholstered furniture, manufactured by applying to one side of a single jersey weft-knitted base cloth a substantially continuous coating of a suitably plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride.
|
Withdrawn |
1994-10 |
Edition : 2 |
Number of pages : 13 |
Technical Committee |
97.140
Furniture
;
59.080.40
Coated fabrics
|
| ISO 7617-1:2001 |
Plastics-coated fabrics for upholstery — Part 1: Specification for PVC-coated knitted fabrics |
This part of ISO 7617 specifies technical requirements for coated fabrics for upholstered furniture for interior use,
obtained by applying to one side of a weft-knitted base cloth a substantially continuous coating of a suitably
plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride. Such coatings
are known as poly(vinyl chloride) (PVC) coatings. The present specification covers fabrics coated with solid PVC
and also covers two grades with coatings consisting of a layer of expanded PVC.
|
Published |
2001-12 |
Edition : 3 |
Number of pages : 17 |
Technical Committee |
97.140
Furniture
;
59.080.40
Coated fabrics
|
| ISO/DIS 7617-1 |
Plastics-coated fabrics for upholstery — Part 1: Specification for PVC-coated knitted fabrics |
This part of ISO 7617 specifies technical requirements for coated fabrics for upholstered furniture for interior use,
obtained by applying to one side of a weft-knitted base cloth a substantially continuous coating of a suitably
plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride. Such coatings
are known as poly(vinyl chloride) (PVC) coatings. The present specification covers fabrics coated with solid PVC
and also covers two grades with coatings consisting of a layer of expanded PVC.
|
Under development |
|
Edition : 4 |
|
Technical Committee |
83.140
Rubber and plastics products
;
97.140
Furniture
;
59.080.40
Coated fabrics
|
| ISO 7617-2:1988 |
Plastics-coated fabrics for upholstery — Part 2: Specification for PVC-coated woven fabrics |
|
Withdrawn |
1988-06 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
83.140
Rubber and plastics products
;
97.140
Furniture
|
| ISO 7617-2:1994 |
Plastics-coated fabrics for upholstery — Part 2: Specification for PVC-coated woven fabrics |
Cancels and replaces the first edition (1988). Specifies requirements for coated fabrics for upholstered furniture, manufactured by applying to one side of a woven cloth a substantially continuous coating of a suitably plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride.
|
Withdrawn |
1994-10 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
97.140
Furniture
;
59.080.40
Coated fabrics
|
| ISO 8555-4:1987 |
Hardware for furniture — Terms for furniture fittings — Part 4: Holding devices, flap stays, lid stays |
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
97.140
Furniture
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 7617-2:2003 |
Plastics-coated fabrics for upholstery — Part 2: Specification for PVC-coated woven fabrics |
ISO 7617-2:2003 specifies requirements for coated fabrics for upholstered furniture, manufactured by applying to one side of a woven cloth a substantially continuous coating of a suitably plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride. Such coatings are known as poly(vinyl chloride) (PVC) coatings. The present specification covers two grades (A and B) of PVC-coated woven fabric.
|
Published |
2003-08 |
Edition : 3 |
Number of pages : 8 |
Technical Committee |
97.140
Furniture
;
59.080.40
Coated fabrics
|
| ISO 7617-3:1988 |
Plastics-coated fabrics for upholstery — Part 3: Specification for polyurethane-coated woven fabrics |
Specifies requirements for polyurethane-coated fabrics for upholstered furniture, where a substantially continuous coating is applied to one side of the fabric. Two annexes for the selection of the specimen and for the determination of the resistance to print wear. Part 1 of this standard: PVC-coated knitted fabrics; part 2: PVC-coated woven fabrics.
|
Published |
1988-06 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
97.140
Furniture
;
59.080.40
Coated fabrics
|
| ISO 8191-1:1987 |
Furniture — Assessment of the ignitability of upholstered furniture — Part 1: Ignition source: smouldering cigarette |
Belongs to a series of standards concerned with the major subjekt; further parts will extend the range by using larger flames. The measurements are intended for a combination of materials used in upholstered seating and not for a particular finished item of furniture incorporating these material. They only give an indication of, but cannot guarantee, the ignition behaviour of the finished item of furniture.
|
Published |
1987-02 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
97.140
Furniture
;
13.220.40
Ignitability and burning behaviour of materials and products
|
| ISO 8191-2:1988 |
Furniture — Assessment of ignitability of upholstered furniture — Part 2: Ignition source: match-flame equivalent |
Belongs to a series of standards concerned with the major subject. The three annexes do not form integral parts of ISO 8191-2. The test methods are intended for a combination of materials used such as covers and fillings in uphlostered seating, and not for a particular finished item of furniture incorporating these materials. They only give an indication of, but cannot guarantee, the ignition behaviour of the finished item of furniture.
|
Published |
1988-10 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
97.140
Furniture
;
13.220.40
Ignitability and burning behaviour of materials and products
|
| ISO 8554-1:1987 |
Hardware for furniture — Terms for furniture locks — Part 1: Latch lock, dead lock, rod- operating lock, central locking system, cylinder lock, combination lock |
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 14 |
Technical Committee |
97.140
Furniture
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 8554-2:1987 |
Hardware for furniture — Terms for furniture locks — Part 2: Surface-mounted lock, inset-type lock, mortise lock |
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
97.140
Furniture
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 8554-3:1987 |
Hardware for furniture — Terms for furniture locks — Part 3: Left hand lock, right hand lock, down lock, up lock |
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
97.140
Furniture
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 8554-4:1987 |
Hardware for furniture — Terms for furniture locks — Part 4: Key, rotary lock-handle, cylinder |
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
97.140
Furniture
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 8555-1:1987 |
Hardware for furniture — Terms for furniture fittings — Part 1: Assembly fittings |
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
97.140
Furniture
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 8555-2:1987 |
Hardware for furniture — Terms for furniture fittings — Part 2: Hinges and flap hinges |
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
97.140
Furniture
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 8555-3:1987 |
Hardware for furniture — Terms for furniture fittings — Part 3: Drawer slides and sliding door gears |
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
97.140
Furniture
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 8555-6:1987 |
Hardware for furniture — Terms for furniture fittings — Part 6: Shelf supports, hanging rails, cabinet suspension brackets |
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
97.140
Furniture
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 8555-7:1987 |
Hardware for furniture — Terms for furniture fittings — Part 7: Handles, knobs, escutcheons, escutcheon insets |
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
97.140
Furniture
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 8555-8:1987 |
Hardware for furniture — Terms for furniture fittings — Part 8: Castors and glides |
|
Withdrawn |
1987-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
97.140
Furniture
;
01.040.97
Domestic and commercial equipment. Entertainment. Sports (Vocabularies)
|
| ISO 9098-1:1994 |
Bunk beds for domestic use — Safety requirements and tests — Part 1: Safety requirements |
Lays down requirements relating to the safety of bunk beds for domestic use. Intended to minimize the risk of accidents happening to children. Only the sleeping function is considered. Also applies to single beds for use at a height of the bed base of 800 mm or more above floor level, irrespective of the use to which the space below is put.
|
Published |
1994-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
97.140
Furniture
|
| ISO 9098-1 |
Bunk beds and high beds — Safety requirements and tests — Part 1: Safety requirements |
|
Under development |
|
Edition : 2 |
|
Technical Committee |
97.140
Furniture
|
| ISO 9098-2:1994 |
Bunk beds for domestic use — Safety requirements and tests — Part 2: Test methods |
Specifies test methods to assess the safety of bunk beds for domestic use. Also applies to single beds for use at a height of the bed base of 800 mm or more above floor level, irrespective of the use to which the space below is put. The tests consist of the application, to various parts of the bunk bed, of loads or forces simulating normal functional use, as well as misuse that can reasonably be expected to occur. The test results are only valid for the article testet.
|
Published |
1994-11 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
97.140
Furniture
|
| ISO 9098-2 |
Bunk beds and high beds — Safety requirements and tests — Part 2: Test methods |
|
Under development |
|
Edition : 2 |
|
Technical Committee |
97.140
Furniture
|
| ISO 9221-1:1992 |
Furniture — Children's high chairs — Part 1: Safety requirements |
Specifies requirements relating to the safety of children's high chairs for domestic use, with the aim of minimizing accidents to children resulting from normal usage and reasonably foreseeable misuse.
|
Withdrawn |
1992-06 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
97.140
Furniture
|
| ISO 9221-1:2015 |
Furniture — Children's high chairs — Part 1: Safety requirements |
ISO 9221-1:2015 specifies safety requirements for children's high chairs intended for children from 6 months to 36 months of age.
If the product can be converted into a product for which an ISO safety standard exists, it is intended that the product also fulfil the requirements of that International Standard.
|
Published |
2015-11 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
97.140
Furniture
|
| ISO 9221-2:1992 |
Furniture — Children's high chairs — Part 2: Test methods |
Specifies test methods that assess the safety requirements given in ISO 9221-1 of children's high chairs and multi-purpose chairs for domestic use. The tests consist of the application, to various parts of the item, of forces simulating normal functional use, as well as misuse, that can reasonably be expected to occur. The tests are designed to evaluate properties without regard to materials, design/construction or manufacturing processes.
|
Withdrawn |
1992-06 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
97.140
Furniture
|
| ISO 9221-2:2015 |
Furniture — Children's high chairs — Part 2: Test methods |
ISO 9221-2:2015 specifies test methods for the assessment of the requirements of children's high chairs.
|
Published |
2015-11 |
Edition : 2 |
Number of pages : 24 |
Technical Committee |
97.140
Furniture
|
| ISO/CD 9221 |
Furniture — Children's high chairs — Safety requirements and test methods |
This document specifies safety requirements for children's high chairs intended for children from 6 months to 36 months of age.
|
Under development |
|
Edition : 1 |
|
Technical Committee |
97.140
Furniture
|