| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO 1015:1992 |
Brown coals and lignites — Determination of moisture content — Direct volumetric method |
Describes the principle, the reagents, the preparation of the sample, the apparatus and calibration, the procedure and precision of the method, the expression of results and the contents of the test report.
|
Withdrawn |
1992-03 |
Edition : 2 |
Number of pages : 3 |
Technical Committee |
73.040
Coals
|
| ISO 1017:1975 |
Brown coals and lignites — Determination of acetone-soluble material ("resinous substances") in the benzene extract |
|
Withdrawn |
1975-11 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
73.040
Coals
|
| ISO 1017:1985 |
Brown coals and lignites — Determination of acetone-soluble material ("resinous substances") in the toluene-soluble extract |
A sample of toluene-soluble extract from brown coal or lignite obtained by the procedure describes in ISO 975 is extracted with acetone at a temperature of 18 to 22 °C. The soluble fraction is filtered or centrifuged off and after evaporation of the solvent dried to constant mass. The percentage of acetone-soluble material is calculated from the mass of reidue after drying.
|
Withdrawn |
1985-12 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
73.040
Coals
|
| ISO 1017:2006 |
Brown coals and lignites — Determination of acetone-soluble material ("resinous substance") in the benzene-soluble extract |
ISO 1017:2006 specifies a method of determining the mass fraction of acetone-soluble material ("resinous substance") in the benzene-soluble extract from brown coals and lignites.
|
Published |
2006-12 |
Edition : 3 |
Number of pages : 4 |
Technical Committee |
73.040
Coals
|
| ISO 1018:1975 |
Hard coal — Determination of moisture-holding capacity |
The coal is brought to equilibrium with an atmosphere 96 % relative humidity at 30 °C and then dried to constant mass at 105 to 110 °C. The conditioning of the coal may be carried out either at atmospheric pressure or under reduced pressure. The moisture-holding capacity is reported as a percentage, by mass, of the conditioned moist coal.
|
Withdrawn |
1975-11 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
73.040
Coals
|
| ISO 1018:2019 |
Hard coal — Determination of moisture-holding capacity |
This document gives reference to ASTM D1412 as a method of determining the moisture-holding capacity of hard coals.
|
Published |
2019-09 |
Edition : 2 |
Number of pages : 2 |
Technical Committee |
73.040
Coals
|
| ISO 5068-1:2007 |
Brown coals and lignites — Determination of moisture content — Part 1: Indirect gravimetric method for total moisture |
ISO 5068-1:2007 specifies two methods for determination of the total moisture content of brown coals and lignites using an indirect gravimetric single-stage method and a two-stage method.
|
Published |
2007-02 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
73.040
Coals
|
| ISO 1170:1977 |
Coal and coke — Calculation of analyses to different bases |
Gives formulae which allow analytical data relating to coal and coke to be expressed on the various different bases in common use. Consideration is given to corrections that may be applied to certain determind values for coal prior ti their calculation to other bases. In a table formulae for calculation of results to different bases are given.
|
Withdrawn |
1977-03 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO 1170:2008 |
Coal and coke — Calculation of analyses to different bases |
ISO 1170:2008 gives equations that allow analytical data relating to coal and coke to be expressed on the various different bases in common use. Consideration is given to corrections that can be applied to certain determined values for coal prior to their calculation to other bases.
|
Withdrawn |
2008-10 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO 1170:2013 |
Coal and coke — Calculation of analyses to different bases |
ISO 1170:2013 gives equations that allow analytical data relating to coal and coke to be expressed on the various different bases in common use. Consideration is given to corrections that can be applied to certain determined values for coal prior to their calculation to other bases.
|
Withdrawn |
2013-07 |
Edition : 3 |
Number of pages : 7 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO 1170:2020 |
Coal and coke — Calculation of analyses to different bases |
|
Published |
2020-09 |
Edition : 4 |
Number of pages : 7 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO 1213-1:1982 |
Solid mineral fuels — Vocabulary — Part 1: Terms relating to coal preparation |
|
Withdrawn |
1982-11 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
73.040
Coals
;
01.040.73
Mining and minerals (Vocabularies)
|
| ISO 1213-1:1982/Add 1:1989 |
Solid mineral fuels — Vocabulary — Part 1: Terms relating to coal preparation — Addendum 1 |
|
Withdrawn |
1989-05 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
73.040
Coals
;
01.040.73
Mining and minerals (Vocabularies)
|
| ISO 1213-1:1993 |
Solid mineral fuels — Vocabulary — Part 1: Terms relating to coal preparation |
Defines, in English, 420 terms commonly employed in coal preparation under the following headlines: general terms, sizing, cleaning, separation of solids from water or air, size reduction, expression of results, blending and homogenization, automatic control.
|
Withdrawn |
1993-12 |
Edition : 2 |
Number of pages : 20 |
Technical Committee |
73.040
Coals
;
01.040.73
Mining and minerals (Vocabularies)
|
| ISO 1213-1:2020 |
Coal and coke — Vocabulary — Part 1: Terms relating to coal preparation |
This document defines terms commonly employed in coal preparation.
Note For terms relating to petrographic analysis, see ISO 7404-1.
|
Published |
2020-09 |
Edition : 3 |
Number of pages : 59 |
Technical Committee |
73.040
Coals
;
01.040.73
Mining and minerals (Vocabularies)
|
| ISO 1213-2:1992 |
Solid mineral fuels — Vocabulary — Part 2: Terms relating to sampling, testing and analysis |
Defines 205 terms commonly employed in this field. Alternative names are given for several terms: in some cases, however, the use of the alternative name is deprecated (as indicated).
|
Withdrawn |
1992-04 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
73.040
Coals
;
01.040.73
Mining and minerals (Vocabularies)
;
01.040.75
Petroleum and related technologies (Vocabularies)
;
75.160.10
Solid fuels
|
| ISO/R 1213-2:1971 |
Vocabulary of terms relating to solid mineral fuels — Part 2: Terms relating to coal sampling and analysis |
|
Withdrawn |
1971-11 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
73.040
Coals
;
01.040.73
Mining and minerals (Vocabularies)
|
| ISO 1213-2:2016 |
Solid mineral fuels — Vocabulary — Part 2: Terms relating to sampling, testing and analysis |
ISO 1213-2:2016 defines terms commonly employed in the sampling, testing and analysis of solid mineral fuels.
Alternative names are given for several terms. In some cases, however, the use of the alternative name is deprecated (as indicated).
An alphabetical index, with numerical cross reference is provided.
|
Published |
2016-12 |
Edition : 2 |
Number of pages : 35 |
Technical Committee |
73.040
Coals
;
01.040.73
Mining and minerals (Vocabularies)
;
01.040.75
Petroleum and related technologies (Vocabularies)
;
75.160.10
Solid fuels
|
| ISO 1952:1976 |
Brown coals and lignites — Method of extraction for the determination of sodium and potassium soluble in dilute hydrochloric acid |
The sample of brown coal or lignite is extracted with boiling 0,005 N hydrochloric acid and the extract centrifuged. The sodium and potassium in solution are determined by any precise analytical method (for example, gravimetric method or flame photometric method).
|
Withdrawn |
1976-06 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
73.040
Coals
|
| ISO 1952:2008 |
Solid mineral fuels — Determination of extractable metals in dilute hydrochloric acid |
ISO 1952:2008 describes the extraction from solid mineral fuels by dilute hydrochloric acid and determination of extractable sodium, potassium, calcium, iron and magnesium.
|
Published |
2008-09 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
73.040
Coals
|
| ISO 1953:1972 |
Hard coals — Size analysis |
|
Withdrawn |
1972-08 |
Edition : 1 |
Number of pages : 16 |
Technical Committee |
73.040
Coals
|
| ISO 1953:1994 |
Hard coal — Size analysis by sieving |
Specifies reference methods for the size analysis of coal by manual sieving (wet or dry), using test sieves of aperture sizes between 125 mm and 45 µm. A guide to sampling is given in annex A and notes on the use of mechanical sieving are given in annex B. Is applicable to all hard coals. Is not applicable to coke or other manufactured fuels. In the case of pulverized coal, the methods described will determine only the percentage of oversize.
|
Withdrawn |
1994-07 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
73.040
Coals
|
| ISO 1953:2015 |
Hard coal — Size analysis by sieving |
ISO 1953:2015 specifies reference methods for the size analysis of coal by manual sieving (wet or dry), using test sieves of aperture sizes between 125 mm and 45 μm. A guide to sampling is given in Annex A.
This International Standard is applicable to all hard coals. It is not applicable to coke or other manufactured fuels.
In the case of pulverized coal which has been ground so that a high proportion passes through the test sieve of smallest aperture size, the methods described in this International Standard will determine only the percentage oversize.
|
Published |
2015-11 |
Edition : 3 |
Number of pages : 13 |
Technical Committee |
73.040
Coals
|
| ISO 1988:1975 |
Hard coal — Sampling |
Forms a comprehensive document dealing with allaspects of the sampling of coal. It specifies methods of sampling hard coal, for both routine and special purposes, to provide samples for general analysis and for the determination of total moisture. It also outlines the principles to be taken into consideration when taking the sample and preparing it for analysis.
|
Withdrawn |
1975-03 |
Edition : 1 |
Number of pages : 90 |
Technical Committee |
73.040
Coals
|
| ISO 1994:1976 |
Hard coal — Determination of oxygen content |
The sample is dried at 105 to 110 °C in a stream of nitrogen and then pyrolysed under conditions in which the organic matter leaves an oxygen-free char. The volatile products, containing the organically bound oxygen and also water and carbon dioxide from any mineral matter, are decomposed with either pure carbon or platinized carbon to convert the oxygen to carbon monoxide. The carbon monoxide is oxidized to carbon dioxide and determined by a titrimetric or a gravimetric procedure.
|
Withdrawn |
1976-12 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
73.040
Coals
|
| ISO 2950:1974 |
Brown coals and lignites — Classification by types on the basis of total moisture content and tar yield |
Brown coals are classified in this International Standard according to the following properties: total moisture content calculated on the ash-free basis; tar hiels calculated on the dry, ash-free basis. In tables class numbers, group number and code numbers of brown coal types are given.
|
Published |
1974-02 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
73.040
Coals
|
| ISO/TS 4667:2022 |
Coal — Determination of the thermal stability and thermal fragmentation |
This document specifies methods for the determination of thermal stability and thermal fragmentation of coal. It is applicable to brown coal and lignites, anthracites and bituminous coal with a caking index of zero (determined by ISO 15585).
|
Published |
2022-08 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO/TS 4676:2022 |
Coal — Determination of carboxyreactivity |
This document specifies the method for determining the reactivity of coal with carbon dioxide (carboxyreactivity). It can be applied to determine the reactivity of coke for the purpose of gasification and combustion.
|
Published |
2022-07 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO/TS 4699:2022 |
Hard Coal — Determination of plastometric indices — Manual method |
This document specifies a manual method for the determination of plastometric indices. These indices are the maximum thickness of the plastic layer (Y, mm) and the final contraction value (X, mm).
This document is applicable for hard coals with a determined ash level less than 15 % on a dry basis, as described in ISO 11722 and ISO 1171.
|
Published |
2022-08 |
Edition : 1 |
Number of pages : 26 |
Technical Committee |
73.040
Coals
|
| ISO 5068-2:2007 |
Brown coals and lignites — Determination of moisture content — Part 2: Indirect gravimetric method for moisture in the analysis sample |
ISO 5068-2:2007 specifies a method for the determination of the moisture content in the analysis sample of brown coals and lignites using an indirect gravimetric method.
|
Published |
2007-02 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
73.040
Coals
|
| ISO 5068:1983 |
Brown coals and lignites — Determination of moisture content — Indirect gravimetric method |
Specifies two basic procedures: a) A single-stage method which can be used for determination of the total moisture content of the special moisture sample or of a moisture sample taken from a common sample. b) A two-stage method which can be used for determination of the residual moisture content and, if required, also the total moisture content of a special moisture sample or of a moisture sample taken from a common sample. The single-stage method consists in drying the sample to constant mass at a temperature of 105 to 110 °C under specified conditions. The two stage method contains additionally drying at temperaures not exceeding 40 °C.
|
Withdrawn |
1983-10 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
73.040
Coals
|
| ISO 5069-1:1983 |
Brown coals and lignites — Principles of sampling — Part 1: Sampling for determination of moisture content and for general analysis |
Part 1 of this standard presents the principles of methods for the sampling of brown coals and lignites from streams, wagons, barges and stock-piles which differ from those described in sampling of hard coals. Other general principles and the procedure of replicate sampling are the same as for hard coals.
|
Withdrawn |
1983-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
73.040
Coals
|
| ISO 5069-2:1983 |
Brown coals and lignites — Principles of sampling — Part 2: Sample preparation for determination of moisture content and for general analysis |
The process of sample preparation consists of several operations three of which are fundamental: particle size reduction by crushing or grinding and milling; mixing; decrease of sample mass by dividing the sample (sample division). In most cases, the drying process of the sample is also necessary.
|
Withdrawn |
1983-12 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
73.040
Coals
|
| ISO 5071-1:1997 |
Brown coals and lignites — Determination of the volatile matter in the analysis sample — Part 1: Two-furnace method |
|
Withdrawn |
1997-07 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
73.040
Coals
|
| ISO 5071-1:2013 |
Brown coals and lignites — Determination of the volatile matter in the analysis sample — Part 1: Two-furnace method |
ISO 5071-1:2013 specifies a method of determining the volatile matter of brown coals and lignites.
|
Withdrawn |
2013-05 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
73.040
Coals
|
| ISO 5071-1:2021 |
Brown coals and lignites — Determination of the volatile matter in the analysis sample — Part 1: Two-furnace method |
This document specifies a method of determining the volatile matter of brown coals and lignites.
|
Published |
2021-12 |
Edition : 3 |
Number of pages : 8 |
Technical Committee |
73.040
Coals
|
| ISO 5072:1997 |
Brown coals and lignites — Determination of true relative density and apparent relative density |
|
Withdrawn |
1997-07 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
73.040
Coals
|
| ISO 5072:2013 |
Brown coals and lignites — Determination of true relative density and apparent relative density |
ISO 5072:2013 describes methods for the determination of true relative density and the apparent relative density of brown coals and lignites.
|
Withdrawn |
2013-05 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
73.040
Coals
|
| ISO 5072:2021 |
Brown coals and lignites — Determination of true relative density and apparent relative density |
This document describes methods for the determination of true relative density and the apparent relative density of brown coals and lignites.
|
Published |
2021-12 |
Edition : 3 |
Number of pages : 7 |
Technical Committee |
73.040
Coals
|
| ISO 5073:1985 |
Brown coals and lignites — Determination of humic acids |
|
Withdrawn |
1985-07 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
73.040
Coals
|
| ISO 5073:1999 |
Brown coals and lignites — Determination of humic acids |
|
Withdrawn |
1999-12 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
73.040
Coals
|
| ISO 5073:2013 |
Brown coals and lignites — Determination of humic acids |
ISO 5073:2013 specifies volumetric methods for the determination of total humic acids and free humic acid of brown coals and lignites.
|
Withdrawn |
2013-05 |
Edition : 3 |
Number of pages : 7 |
Technical Committee |
73.040
Coals
|
| ISO 5073:2021 |
Brown coals and lignites — Determination of humic acids |
This document specifies volumetric methods for the determination of total humic acids and free humic acid of brown coals and lignites.
|
Published |
2021-12 |
Edition : 4 |
Number of pages : 7 |
Technical Committee |
73.040
Coals
|
| ISO 5074:1994 |
Hard coal — Determination of Hardgrove grindability index |
Cancels and replaces the first edition (1980). Specifies the method for determining the grindability index of hard coal using the Hardgrove machine. Also specifies the procedure for calibrating the test machine and for preparing the standard reference coal samples.
|
Withdrawn |
1994-12 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
73.040
Coals
|
| ISO 5074:2015 |
Hard coal — Determination of Hardgrove grindability index |
ISO 5074:2015 specifies the method for determining the grindability index of hard coal using the Hardgrove machine. It also specifies the procedure for calibrating the test machine and for preparing the standard reference coal samples.
NOTE In this International Standard, the term "hard coal" is used as an indication of maturity or rank in the coalification sequence and is not related to the physical properties of the coal.
|
Published |
2015-10 |
Edition : 3 |
Number of pages : 1 |
Technical Committee |
73.040
Coals
|
| ISO 7404-1:1984 |
Methods for the petrographic analysis of bituminous coal and anthracite — Part 1: Glossary of terms |
|
Withdrawn |
1984-10 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
73.040
Coals
;
01.040.73
Mining and minerals (Vocabularies)
|
| ISO 7404-1:1994 |
Methods for the petrographic analysis of bituminous coal and anthracite — Part 1: Vocabulary |
Cancels and replaces the first edition (1984). Defines terms that are used in connection both with maceral and microlithotype analyses carried out in white light and with the determination of the reflectance of vitrinite. Applies to the terms used in examination of bituminous coal and anthracite only. Not concerned with the analysis of brown coal, sub-bituminous coal or lignite.
|
Withdrawn |
1994-09 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
73.040
Coals
;
01.040.73
Mining and minerals (Vocabularies)
|
| ISO 7404-1:2016 |
Methods for the petrographic analysis of coals — Part 1: Vocabulary |
ISO 7404-1:2016 defines terms that are used in connection with both maceral and microlithotype analyses, and with the determination of the reflectance of vitrinite. It applies to the terms used in the examination of coal of all ranks.
ISO 7404-1:2016 is not intended to be a comprehensive glossary of coal petrographic terminology, nor does it attempt to provide sufficient information to allow recognition of all the coal components described. Further information may be obtained from the relevant ICCP publications[3][4][5].
|
Published |
2016-04 |
Edition : 3 |
Number of pages : 6 |
Technical Committee |
73.040
Coals
;
01.040.73
Mining and minerals (Vocabularies)
|
| ISO 7404-2:1985 |
Methods for the petrographic analysis of bituminous coal and anthracite — Part 2: Preparation of coal samples |
This part of ISO 7404 specifies a method for preparing a polished particulate block from a sample od crushed coal, for analysis by reflectance microscopy using white ligth. It does not apply to the preparation of polished particulate blocks for analysis using fluorescence microscopy techniques nor to the preparation of polished orientated lumps of coal.
|
Withdrawn |
1985-05 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
73.040
Coals
|
| ISO 7404-2:2009 |
Methods for the petrographic analysis of coals — Part 2: Methods of preparing coal samples |
ISO 7404-2:2009 specifies methods for preparing a polished particulate block from a sample of crushed coal for analysis by reflectance microscopy. These methods can also be applied to the preparation of a polished, embedded lump of coal.
|
Published |
2009-10 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
73.040
Coals
|
| ISO 7404-3:1984 |
Methods for the petrographic analysis of bituminous coal and anthracite — Part 3: Method of determining maceral group composition |
|
Withdrawn |
1984-11 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
73.040
Coals
|
| ISO 7404-3:1994 |
Methods for the petrographic analysis of bituminous coal and anthracite — Part 3: Method of determining maceral group composition |
Cancels and replaces the first edition (1984). Specifies a method of determining the proportions of the maceral groups (and the minerals if desired) in coals. Concerned only with determinations made on polished particulate blocks using reflected white light. Not concerned with the determination of the proportions of naturally occurring maceral associations.
|
Withdrawn |
1994-09 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
73.040
Coals
|
| ISO 7404-3:2009 |
Methods for the petrographic analysis of coals — Part 3: Method of determining maceral group composition |
ISO 7404-3:2009 specifies a method for determining the proportions of the maceral groups (and the minerals, if desired) in coals. ISO 7404-3:2009 is applicable only to determinations made on polished particulate blocks using incident white light. For lower-rank coals, the additional use of the fluorescence mode is necessary to identify liptinites.
|
Published |
2009-10 |
Edition : 3 |
Number of pages : 7 |
Technical Committee |
73.040
Coals
|
| ISO 556:2020 |
Coke (greater than 20 mm in size) — Determination of mechanical strength |
This document specifies a method for the determination of the mechanical strength of coke having a particle size greater than 20 mm.
|
Published |
2020-03 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
75.160.10
Solid fuels
|
| ISO 7404-4:1988 |
Methods for the petrographic analysis of bituminous coal and anthracite — Part 4: Method of determining microlithotype, carbominerite and minerite composition |
This part of ISO 7404 applies only to determinations made on polished particular blocks using reflected white ligth. The examination is carried out by using reflected ligth microscope and point count procedure. The microlithotypes are identified from their maceral composition under an immersion medium. The proportions of the macerals are determined using a graticule having a grid with 20 points of intersection.
|
Withdrawn |
1988-12 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
73.040
Coals
|
| ISO 7404-4:2017 |
Methods for the petrographic analysis of coals — Part 4: Method of determining microlithotype, carbominerite and minerite composition |
ISO 7404-4:2017 specifies a method, using a graticule with 20 crossline intersections, for determining the proportions of microlithotypes, carbominerite and minerite in coals. It applies only to determinations made on polished particulate blocks using reflected white light (about 400 nm to 700 nm). Additional blue, blue-violet or UV light excitation (365 nm to 440 nm) for better identification of liptinite in fluorescence may be used especially at low rank coals.
|
Published |
2017-08 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
73.040
Coals
|
| ISO 7404-5:1984 |
Methods for the petrographic analysis of bituminous coal and anthracite — Part 5: Method of determining microscopically the reflectance of vitrinite |
|
Withdrawn |
1984-11 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
73.040
Coals
|
| ISO 7404-5:1994 |
Methods for the petrographic analysis of bituminous coal and anthracite — Part 5: Method of determining microscopically the reflectance of vitrinite |
Cancels and replaces the first edition (1984). Specifies the method for determining microscopically the maximum and random reflectance in oil of polished surfaces of the vitrinite component of coals. Applicable to either coals from single seams or coal blends covering the whole range of bituminous coal and anthracite.
|
Withdrawn |
1994-09 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
73.040
Coals
|
| ISO 7404-5:2009 |
Methods for the petrographic analysis of coals — Part 5: Method of determining microscopically the reflectance of vitrinite |
ISO 7404-5:2009 specifies the methods for determining the reflectance of vitrinite of coals microcopically on the polished surfaces, immersed in oil. The methods are applicable to coals from single seams or coal blends covering the whole range of low-, medium- and high-rank coal.
Vitrinite reflectance measurements can be used to characterize the components within blends. Measures can be taken to correct for the vitrinite percentage within each of the components of the blend or to determine the proportion of components in a blend, particularly when the components have dissimilar vitrinite contents. This method necessitates the identification of vitrinite by the analyst.
Reflectance measurements on vitrinite obtained by interpreting the results from an automated system, are outside the scope of ISO 7404-5:2009.
|
Published |
2009-10 |
Edition : 3 |
Number of pages : 14 |
Technical Committee |
73.040
Coals
|
| ISO 7936:1992 |
Hard coal — Determination and presentation of float and sink characteristics — General directions for apparatus and procedures |
Describes sampling, preliminary treatment, test procedure using relative density separation methods, presentation of results. A general procedure for a centrifugal float and sink test is given in Annex A. A typical procedure for treating and testing a sample of raw coal is described in Annex B. Some practical hints on float and sink testing are given in annex C.
|
Withdrawn |
1992-04 |
Edition : 1 |
Number of pages : 19 |
Technical Committee |
73.040
Coals
|
| ISO 7936:2022 |
Coal — Determination and presentation of float and sink characteristics — General directions for apparatus and procedures |
This document specifies general directions for the apparatus and procedures, using relative density separation methods, for determining the float and sink characteristics of samples from coal seams and of feed, products and rejects from coal preparation plants.
|
Published |
2022-08 |
Edition : 2 |
Number of pages : 54 |
Technical Committee |
73.040
Coals
|
| ISO 8264:1989 |
Hard coal — Determination of the swelling properties using a dilatometer |
A test piece, in the form of a pencil, prepared from powdered coal is heated at a constant rate in a steel retort positioned in a furnace, the temperature monitoring system having been previously calibrated using two reference metals of known melting points. The change in level of a piton resting upon the test piece is observed continuously, and record is produced which is characteristic of the swelling properties of the coal.
|
Published |
1989-11 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
73.040
Coals
|
| ISO 8833:1989 |
Magnetite for use in coal preparation — Test methods |
Specifies methods for sampling and testing of magnetite. The specified tests should ensure that the properties which make magnetite suitable for coal preparation purpose are simply and adequately tested. These properties are: moisture content, particle size distribution, total magnetics content, relative density, total iron(II) content, fundamental magnetic properties.
|
Published |
1989-11 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
73.040
Coals
|
| ISO 8858-1:1990 |
Hard coal — Froth flotation testing — Part 1: Laboratory procedure |
|
Withdrawn |
1990-09 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
73.040
Coals
|
| ISO 8858-1:2019 |
Hard coal — Froth flotation testing — Part 1: Laboratory procedure |
This document sets out a laboratory procedure for the froth flotation testing of fine coal, e.g. coal of particle size less than 0,5 mm. The procedure provides a means of evaluating the general flotation characteristics of a coal under a set of specified standard conditions, and will not necessarily indicate the full flotation potential of that coal.
The flotation characteristics of coals are sensitive to changes in flotation conditions. These conditions can be changed by varying basic parameters such as flotation time, reagent and dosage rate. Separate flotation tests are used to assess the effect of varying these parameters to determine the best flotation conditions for a particular coal. A method of evaluating flotation response will be given in a separate standard.
|
Published |
2019-06 |
Edition : 2 |
Number of pages : 14 |
Technical Committee |
73.040
Coals
|
| ISO 8858-2:2004 |
Hard coal — Froth flotation testing — Part 2: Sequential evaluation |
ISO 8858-2:2004 sets out a laboratory sequential procedure for the froth flotation testing of fine coal, e.g. coal having a particle size of less than 0,5 mm. The procedure provides a means of evaluating for a coal the flotation characteristics (expressed as a yield/ash relationship) that may be expected from the froth flotation process.
Pulp samples that cannot be dewatered without the use of heat or chemical additives are not covered by this part of ISO 8858; nor does it cover procedures for the investigation of flotation kinetics.
The test is not intended to provide plant design data.
|
Published |
2004-08 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
73.040
Coals
|
| ISO 8858-3:2004 |
Hard coal — Froth flotation testing — Part 3: Release evaluation |
ISO 8858-3:2004 describes a laboratory method for release evaluation of the froth flotation characteristics of hard coal, of particle size less than 0.5 mm. It is applicable to coal in powder form or in the form of a slurry.
|
Published |
2004-08 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
73.040
Coals
|
| ISO 9411-1:1994 |
Solid mineral fuels — Mechanical sampling from moving streams — Part 1: Coal |
Provides recommended practices for the mechanical sampling of solid mineral fuels from moving streams. Applicable to the mechanical sampling and preparation of coal samples for the determination of total moisture, general analysis, including physical and chemical tests, and size analysis. Describes the basic requirements, together with typical examples of applications für guidance in the design, installation and operation of systems for mechanical sampling and mechanical preparation of samples.
|
Withdrawn |
1994-10 |
Edition : 1 |
Number of pages : 89 |
Technical Committee |
73.040
Coals
|
| ISO 9931:1991 |
Coal — Sampling of pulverized coal conveyed by gases in direct fired coal systems |
Specifies a method which, subject to limitations imposed by the geometry of the pulverized-coal pipe, is applicable to multipoint sampling. Annexes A, B and C are for information only.
|
Published |
1991-12 |
Edition : 1 |
Number of pages : 18 |
Technical Committee |
73.040
Coals
|
| ISO 10086-1:2000 |
Coal — Methods for evaluating flocculants for use in coal preparation — Part 1: Basic parameters |
|
Withdrawn |
2000-06 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
73.040
Coals
|
| ISO 10086-1:2019 |
Coal — Methods for evaluating flocculants for use in coal preparation — Part 1: Basic parameters |
This document specifies a method for the comparative evaluation of the performances of flocculants for clarification, thickening and sedimentation applications on a given slurry. This performance can be evaluated by
a) the settling velocity in the initial period,
b) the sediment volume after compaction and consolidation, and
c) the clarity of the supernatant liquid.
|
Published |
2019-07 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
73.040
Coals
|
| ISO 10086-2:2004 |
Coal — Methods for evaluating flocculants for use in coal preparation — Part 2: Flocculants as filter aids in rotary vacuum filtration systems |
ISO 10086-2:2004 specifies a method for the comparative evaluation of the performance of flocculants used as filter aids for rotary vacuum filtration applications on a given slurry.
|
Published |
2004-01 |
Edition : 1 |
Number of pages : 12 |
Technical Committee |
73.040
Coals
|
| ISO 10329:2009 |
Coal — Determination of plastic properties — Constant-torque Gieseler plastometer method |
ISO 10329:2009 specifies a method for obtaining a relative measure of the plastic behaviour of coal when heated under prescribed conditions. The method may be used to obtain values of the plastic properties of coals and blends used in carbonization and in other situations where determination of plastic behaviour of coals is of practical importance.
|
Withdrawn |
2009-02 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
73.040
Coals
|
| ISO 10329:2017 |
Coal — Determination of plastic properties — Constant-torque Gieseler plastometer method |
ISO 10329:2017 specifies a method for obtaining a relative measure of the plastic behaviour of coal when heated under prescribed conditions. The method is used to obtain values of the plastic properties of coals and blends used in carbonization and in other situations where determination of plastic behaviour of coals is of practical importance.
NOTE The empirical nature of this test requires proper equipment calibration to produce fluidity readings which are a true indication of the relative plastic behaviour of the coal.
|
Published |
2017-07 |
Edition : 2 |
Number of pages : 13 |
Technical Committee |
73.040
Coals
|
| ISO 11723:2004 |
Solid mineral fuels — Determination of arsenic and selenium — Eschka's mixture and hydride generation method |
ISO 11723:2004 specifies a method using Eschka's mixture during ashing, extraction of the ash residue with acid, and hydride generation atomic absorption spectrometry or hydride generation atomic fluorescence spectrometry, for the determination of arsenic and selenium in coal and coke ash.
|
Withdrawn |
2004-11 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
73.040
Coals
|
| ISO 11723:2016 |
Solid mineral fuels — Determination of arsenic and selenium — Eschka's mixture and hydride generation method |
ISO 11723:2016 specifies a method using Eschka's mixture during ashing, extraction of the ash residue with acid, and hydride generation atomic absorption spectrometry or hydride generation atomic fluorescence spectrometry, for the determination of arsenic and selenium in solid mineral fuels.
|
Published |
2016-11 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
73.040
Coals
|
| ISO 11724:2004 |
Solid mineral fuels — Determination of total fluorine in coal, coke and fly ash |
ISO 11724:2004 specifies a method for the determination of total fluorine in coal, coke and fly ash.
|
Withdrawn |
2004-11 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
73.040
Coals
|
| ISO 11724:2016 |
Solid mineral fuels — Determination of total fluorine in coal, coke and fly ash |
ISO 11724:2016 specifies a method for the determination of total fluorine in coal, coke and fly ash.
From measurement of the total fluorine alone, it is not possible to estimate the amount of fluorine released to the environment by utilization of the coal and subsequent disposal of the ash residue.
|
Withdrawn |
2016-12 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
73.040
Coals
|
| ISO 11724:2019 |
Solid mineral fuels — Determination of total fluorine in coal, coke and fly ash |
This document specifies a method for the determination of total fluorine in coal, coke and fly ash.
From measurement of the total fluorine alone, it is not possible to estimate the amount of fluorine released to the environment by utilization of the coal and subsequent disposal of the ash residue.
|
Published |
2019-06 |
Edition : 3 |
Number of pages : 11 |
Technical Committee |
73.040
Coals
|
| ISO 11760:2005 |
Classification of coals |
ISO 11760:2005 describes a simple classification system for coals providing guidance on the selection of the appropriate ISO standard procedures for the analyses and testing, international comparison in terms of some key characteristics and descriptive categorization of coals. The system is applicable to coals of all ranks, but care is required in relation to the classification of some types of coal. It is also applicable to a wide range of representative coal samples, provided their exact nature is stated. Such samples include bore-core seam sections and composite samples, raw (as-mined) coal, washed coal, blends of coals of similar rank and selected, specified size fractions.
|
Withdrawn |
2005-02 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
73.040
Coals
|
| ISO 11760:2018 |
Classification of coals |
This document describes a simple classification system for coals providing
— guidance on the selection of the appropriate ISO standard procedures for the analyses and testing of coals,
— international comparison of coals in terms of some key characteristics,
— descriptive categorization of coals.
The system is applicable to coals of all ranks, but care is required in relation to the classification of some types of coal.
The system can be applied to a wide range of representative coal samples, provided their exact nature is stated. Such samples include bore-core seam sections and composite samples, raw (as-mined) coal, washed coal, blends of coals of similar rank and selected, specified size fractions.
The system provides a broad framework within which coals can be assessed. The selection of coals for a specific use requires detailed information that enables the likely performance of a coal in a particular application to be anticipated. The wide-ranging list of ISO analyses and test procedures for coals serve this purpose. The selection of the appropriate procedures to be used in assessing a coal depends on the intended use.
|
Published |
2018-11 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
73.040
Coals
|
| ISO 12900:1997 |
Hard coal - Determination of abrasiveness |
|
Withdrawn |
1997-12 |
Edition : 1 |
Number of pages : 11 |
Technical Committee |
73.040
Coals
|
| ISO 12900:2015 |
Hard coal — Determination of abrasiveness |
ISO 12900:2015 describes a method for determining the abrasiveness of hard coal.
|
Withdrawn |
2015-06 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
73.040
Coals
|
| ISO 12900:2018 |
Hard coal — Determination of abrasiveness |
This document describes a method for determining the abrasiveness of hard coal.
|
Published |
2018-11 |
Edition : 3 |
Number of pages : 10 |
Technical Committee |
73.040
Coals
|
| ISO/TS 12902:2001 |
Solid mineral fuels — Determination of total carbon, hydrogen and nitrogen — Instrumental methods |
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO 13605:2018 |
Solid mineral fuels — Major and minor elements in coal ash and coke ash — Wavelength dispersive x-ray fluorescence spectrometric method |
This document sets out a wavelength dispersive X-ray fluorescence (XRF) procedure for the determination of silicon, aluminium, iron, calcium, magnesium, sodium, potassium, titanium, manganese, phosphorus and sulfur.
|
Published |
2018-10 |
Edition : 1 |
Number of pages : 16 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO/TS 13605:2012 |
Solid mineral fuels — Major and minor elements in hard coal ash and coke ash — Wavelength dispersive X-ray fluorescence spectrometric method |
ISO/TS 13605:2012 sets out a wavelength dispersive X-ray fluorescence procedure for the determination of silicon, aluminium, iron, calcium, magnesium, sodium, potassium, titanium, manganese, phosphorus and sulfur.
The method is applicable to coal ashes, coke ashes and boiler ashes having components within the concentration ranges specified in ISO/TS 13605:2012.
|
Withdrawn |
2012-05 |
Edition : 1 |
Number of pages : 15 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO 13909-1:2001 |
Hard coal and coke — Mechanical sampling — Part 1: General introduction |
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO 13909-1:2016 |
Hard coal and coke — Mechanical sampling — Part 1: General introduction |
ISO 13909-1:2016 defines the basic terms used in the sampling of solid mineral fuels, describes the general principles of sampling and details the information to be provided in the documentation and the sampling report. It also lists the other parts and gives guidance on the selection of the appropriate part.
It does not include sampling of brown coals and lignites, or sampling from coal seams, for which guidance is given in ISO 14180. Manual sampling of coal and coke is covered in ISO 18283.
|
Published |
2016-07 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO 13909-2:2001 |
Hard coal and coke — Mechanical sampling — Part 2: Coal — Sampling from moving streams |
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 31 |
Technical Committee |
73.040
Coals
|
| ISO 13909-2:2016 |
Hard coal and coke — Mechanical sampling — Part 2: Coal — Sampling from moving streams |
ISO 13909-2:1016 specifies procedures and requirements for the design and establishment of mechanical samplers for the sampling of coal from moving streams and describes the methods of sampling used.
It does not cover mechanical sampling from stationary lots which is dealt with in ISO 13909‑3[1].
|
Published |
2016-07 |
Edition : 2 |
Number of pages : 30 |
Technical Committee |
73.040
Coals
|
| ISO 13909-3:2001 |
Hard coal and coke — Mechanical sampling — Part 3: Coal — Sampling from stationary lots |
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 19 |
Technical Committee |
73.040
Coals
|
| ISO 13909-3:2016 |
Hard coal and coke — Mechanical sampling — Part 3: Coal — Sampling from stationary lots |
ISO 13909-3:2016 specifies procedures for the mechanical sampling of coal from stationary lots, for example, from wagons, barges, ships and stockpiles. These procedures are to be used when it is not possible to sample the lots during loading or discharge according to ISO 13909‑2:2016. Procedures for sample preparation are given in ISO 13909‑4:2016.
ISO 13909-3:2016 is applicable to mechanical sampling from stationary coal lots, to obtain samples from which test samples for the determination of moisture, and for general analysis including physical and chemical tests, can be prepared in accordance with the requirements and recommendations set out in ISO 13909‑4:2016.
In ISO 13909-3:2016, the principles and procedures for designing a sampling scheme are given, together with typical examples of applications; in addition, practices for the execution of sampling in different sampling situations are described. The methods described are limited to those on which it is possible to conduct a test for bias.
|
Published |
2016-07 |
Edition : 2 |
Number of pages : 18 |
Technical Committee |
73.040
Coals
|
| ISO 13909-4:2001 |
Hard coal and coke — Mechanical sampling — Part 4: Coal — Preparation of test samples |
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 29 |
Technical Committee |
73.040
Coals
|
| ISO 13909-4:2016 |
Hard coal and coke — Mechanical sampling — Part 4: Coal — Preparation of test samples |
ISO 13909-4:2016 describes the preparation of samples of coal from the combination of primary increments to the preparation of samples for specific tests.
|
Published |
2016-07 |
Edition : 2 |
Number of pages : 30 |
Technical Committee |
73.040
Coals
|
| ISO 13909-7:2001 |
Hard coal and coke — Mechanical sampling — Part 7: Methods for determining the precision of sampling, sample preparation and testing |
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 40 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO 562:1998 |
Hard coal and coke — Determination of volatile matter |
|
Withdrawn |
1998-01 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO 13909-7:2016 |
Hard coal and coke — Mechanical sampling — Part 7: Methods for determining the precision of sampling, sample preparation and testing |
In ISO 13909-7:2016, formulae are developed which link the variables that contribute to overall sampling precision. Methods are described for estimating overall precision and for deriving values for primary increment variance which can be used to modify the sampling scheme to change the precision. Methods for checking the variance of sample preparation and testing are also described.
|
Published |
2016-07 |
Edition : 2 |
Number of pages : 43 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO 13909-8:2001 |
Hard coal and coke — Mechanical sampling — Part 8: Methods of testing for bias |
|
Withdrawn |
2001-12 |
Edition : 1 |
Number of pages : 31 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|
| ISO 13909-8:2016 |
Hard coal and coke — Mechanical sampling — Part 8: Methods of testing for bias |
ISO 13909-8:2016 sets out principles and procedures for testing the bias of test samples of hard coals or cokes, taken in accordance with ISO 13909: 2016 (all parts).
NOTE In the text, the term "fuel" is used where both coal and coke would be applicable in the context and either "coal" or "coke" where only one is applicable.
|
Published |
2016-07 |
Edition : 2 |
Number of pages : 28 |
Technical Committee |
73.040
Coals
;
75.160.10
Solid fuels
|