| Name |
Description |
Abstract |
Status |
Publication date |
Edition |
Number of pages |
Technical committee |
ICS |
| ISO 3781:1983 |
Paper and board — Determination of tensile strength after immersion in water |
Is applicable to board as well as to paper, provided that an apropriate soaking time is agreed between the interested parties. Sampling shall be according to ISO 186, conditioning according to ISO 187 and the determination of tensile strength according to ISO 536.
|
Withdrawn |
1983-06 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
85.060
Paper and board
|
| ISO 3781:2011 |
Paper and board — Determination of tensile strength after immersion in water |
ISO 3781:2011 specifies a test method for the determination of the wet tensile strength of paper or board after its immersion in water for a specified period.
In principle, the method is applicable to both paper and board, provided an appropriate soaking time is agreed between the interested parties.
It is not applicable to tissue paper and tissue products other lightweight, highly absorbent paper which is difficult to handle or of low strength when wet (see ISO 12625‑5).
|
Published |
2011-09 |
Edition : 3 |
Number of pages : 6 |
Technical Committee |
85.060
Paper and board
|
| ISO 3782:1980 |
Paper and board — Determination of resistance to picking — Accelerating speed method using the IGT tester (Pendulum or spring model) |
|
Withdrawn |
1980-02 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
85.060
Paper and board
|
| ISO 3783:1980 |
Paper and board — Determination of resistance to picking — Accelerating speed method using the IGT tester (Electric model) |
Specifies a method of operating the electrical model of the IGT printability tester in order to provide a measure of the picking resistance of paper, and applies to any kind of paper or board likely to be used for printing, mainly by lithographic or letterpress process.
|
Withdrawn |
1980-02 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
85.060
Paper and board
|
| ISO 3783:2006 |
Paper and board — Determination of resistance to picking — Accelerated speed method using the IGT-type tester (electric model) |
ISO 3783:2006 specifies an accelerated speed method for determining the surface strength in terms of the pick velocity and pick resistance of coated and uncoated paper and board, and in terms of the delamination resistance of the liner on paperboard, by simulating the behaviour in the printing process. Because of the limited area tested and the general character of the test, it will not usually detect local imperfections such as surface debris.
This test is especially important for papers and boards which are to be printed in lithographic offset or letterpress, because the inks used in these techniques traditionally have a high viscosity and high tack values. Due to the increasing tendency for the tack and viscosity of modern flexographic inks to be high, this method is also useful in that field.
|
Published |
2006-07 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
85.060
Paper and board
|
| ISO 4046-1:2002 |
Paper, board, pulps and related terms — Vocabulary — Part 1: Alphabetical index |
ISO 4046-1:2002 is an alphabetical index of English and French terms which are defined in the ISO 4046 series of standards, which document the terminology of paper, board, pulp and related terms.
|
Withdrawn |
2002-10 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
85.020
Paper production processes
;
85.040
Pulps
;
85.060
Paper and board
;
01.040.85
Paper technology (Vocabularies)
|
| ISO 4046-1:2016 |
Paper, board, pulps and related terms — Vocabulary — Part 1: Alphabetical index |
ISO 4046-1:2016 is an alphabetical index of English and French terms which are defined in the ISO 4046 series of standards, which document the terminology of paper, board, pulp and related terms.
|
Published |
2016-03 |
Edition : 2 |
Number of pages : 13 |
Technical Committee |
85.020
Paper production processes
;
85.040
Pulps
;
85.060
Paper and board
;
01.040.85
Paper technology (Vocabularies)
|
| ISO 4046-4:2002 |
Paper, board, pulps and related terms — Vocabulary — Part 4: Paper and board grades and converted products |
ISO 4046-4:2002 defines terms related to paper and board grades and converted products, in both English and French.
|
Withdrawn |
2002-10 |
Edition : 1 |
Number of pages : 29 |
Technical Committee |
85.060
Paper and board
;
01.040.85
Paper technology (Vocabularies)
|
| ISO 4046-4:2016 |
Paper, board, pulps and related terms — Vocabulary — Part 4: Paper and board grades and converted products |
ISO 4046-4:2016 defines terms related to paper and board grades and converted products, in both English and French.
|
Published |
2016-03 |
Edition : 2 |
Number of pages : 29 |
Technical Committee |
85.060
Paper and board
;
01.040.85
Paper technology (Vocabularies)
|
| ISO 4046-5:2002 |
Paper, board, pulps and related terms — Vocabulary — Part 5: Properties of pulp, paper and board |
ISO 4046-5:2002 defines terms related to properties of pulp, paper and board, in both English and French.
|
Withdrawn |
2002-10 |
Edition : 1 |
Number of pages : 28 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
;
01.040.85
Paper technology (Vocabularies)
|
| ISO 4046-5:2016 |
Paper, board, pulps and related terms — Vocabulary — Part 5: Properties of pulp, paper and board |
ISO 4046-5:2016 defines terms related to properties of pulp, paper and board, in both English and French.
|
Published |
2016-03 |
Edition : 2 |
Number of pages : 28 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
;
01.040.85
Paper technology (Vocabularies)
|
| ISO 4046:1978 |
Paper, board, pulp and related terms — Vocabulary |
Includes the sections Pulp - Genenral Terms, Pulp Manufacture, Types of Pulp, Paper and Board - General Terms, Paper Marking, Types of Paper and Board - Converted Products, Properties of Pulp, Paper or Board, and has French and English indexes attached to it.
|
Withdrawn |
1978-11 |
Edition : 1 |
Number of pages : 48 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
;
01.040.85
Paper technology (Vocabularies)
|
| ISO 4094:2005 |
Paper, board and pulps — International calibration of testing apparatus — Nomination and acceptance of standardizing and authorized laboratories |
ISO 4094:2005 provides rules for the nomination and appointment of standardizing and authorized laboratories under the jurisdiction of ISO/TC 6, or one of its subcommittees, with the aim of establishing and maintaining the reference standards and distributing the transfer standards required to achieve interlaboratory agreement in the results of a test method specified in an International Standard for paper, board or pulp. It provides guidelines for the establishment of criteria for the initial appointment and continued acceptance of nominated laboratories.
|
Withdrawn |
2005-04 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
85.020
Paper production processes
;
85.040
Pulps
;
85.060
Paper and board
|
| ISO 4094:2017 |
Paper, board and pulps — General requirements for the competence of laboratories authorized for the issue of optical reference transfer standards of level 3 |
ISO 4094:2017 provides both general requirements and specific requirements (Annex A) for laboratories seeking to become "Authorized Laboratories (ALs)" and to maintain their Authorized Laboratory status for the issue of optical reference transfer standards of level 3. This document follows the requirements and adopts the format of ISO/IEC 17025, with the aims of:
a) establishing and maintaining international optical reference transfer standards of level 2 (IR2) traceable to an international optical reference primary standard of level 1 (IR1) maintained by a standardizing laboratory;
b) distributing traceability required to achieve inter-laboratory agreement in the results of test methods specified in International Standards for optical properties of paper, board or pulp;
c) participating in the design and development of new methods and international harmonization of procedures.
When a laboratory does not undertake one or more of the activities covered by this document, such as sampling and the design/development of new methods, the requirements of those clauses do not apply.
ISO 4094:2017 is for use by specified laboratories authorized to issue optical reference transfer standards in developing their management system for quality, administrative and technical operations. Laboratory customers, regulatory authorities and accreditation bodies can also use it in confirming or recognizing the competence of laboratories.
NOTE It might be necessary to explain or interpret certain requirements in this document to ensure that the requirements are applied in a consistent manner. Guidance for consistent application can be obtained from Technical Committee ISO/TC 6.
|
Published |
2017-12 |
Edition : 3 |
Number of pages : 32 |
Technical Committee |
85.020
Paper production processes
;
85.040
Pulps
;
85.060
Paper and board
|
| ISO 5626:1993 |
Paper — Determination of folding endurance |
Specifies the methods for the determination of folding endurance of paper using Köhler-Molin, Lhomargy, MIT and Schopper testers. The principle of the methods is folding backwards and forwards in a standardized manner of a narrow strip of paper subjected to a longitudinal stress, until it breaks. The Köhler-Molin, Lhomargy and Schopper methods are applicable to paper of thicknesses up to 0,25 mm thick and having a tensile strength greater than 1,33 kN/m. The MIT tester has interchangeable folding heads allowing a range of thicknesses up to 1,25 mm.
|
Published |
1993-11 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
85.060
Paper and board
|
| ISO 5626:1978 |
Paper — Determination of folding endurance |
|
Withdrawn |
1978-12 |
Edition : 3 |
Number of pages : 8 |
Technical Committee |
85.060
Paper and board
|
| ISO 5627:1984 |
Paper and board — Determination of smoothness (Bekk method) |
|
Withdrawn |
1984-04 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
85.060
Paper and board
|
| ISO 5627:1995 |
Paper and board — Determination of smoothness (Bekk method) |
Cancels and replaces the first edition (1984). Specifies a method of measuring the smoothness of paper and board, called the Bekk method. Especially recommended for smooth paper and boards. However for very smooth samples, measurement times may be impractically long. Not recommended for materials greater than 0,5 mm thick or very permeable papers and board, since the amount of air passing through the test piece can influence the result. Not recommended for newsprint and not suitable for rough papers and boards.
|
Published |
1995-03 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
85.060
Paper and board
|
| ISO 5627:1995/Cor 1:2002 |
Paper and board — Determination of smoothness (Bekk method) — Technical Corrigendum 1 |
|
Published |
2002-06 |
Edition : 2 |
Number of pages : 1 |
Technical Committee |
85.060
Paper and board
|
| ISO 22476-2:2005/Amd 1:2011 |
Geotechnical investigation and testing — Field testing — Part 2: Dynamic probing — Amendment 1 |
|
Published |
2011-11 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
93.020
Earthworks. Excavations. Foundation construction. Underground works
|
| ISO 5628:1990 |
Paper and board — Determination of bending stiffness by static methods — General principles |
Specifies the general principles to be observed in the preparation of test methods for determining the bending stiffness of all types of paper and board using static methods, by applying line loading to which the mass of the test piece makes negligible contribution. In detail, it describes principle, apparatus, limitations on use of instruments, sampling, conditioning, preparation of test pieces, procedure, expression of results, test report.
|
Withdrawn |
1990-11 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
85.060
Paper and board
|
| ISO 5628:2012 |
Paper and board — Determination of bending stiffness — General principles for two-point, three-point and four-point methods |
ISO 5628:2012 specifies three test methods for determining the bending stiffness of paper and paperboard. The test methods differ in the type of loading mode, thus giving rise to the two-point, three-point and four-point bending test methods.
For paper and paperboard in a low thickness range, the two-point bending method and the three-point bending method are suitable.
For corrugated fibreboard and board with a higher thickness, the four-point bending method is recommended.
The measurement conditions are defined in such a way that the test piece is not subjected to any significant permanent deformation during the test, nor is the range of validity of the equations for calculating the bending stiffness exceeded.
In these bending tests, the test pieces of paper and board are regarded as "beams" as defined by the science of the strength of materials.
|
Withdrawn |
2012-01 |
Edition : 2 |
Number of pages : 10 |
Technical Committee |
85.060
Paper and board
|
| ISO 5628:2019 |
Paper and board — Determination of bending stiffness — General principles for two-point, three-point and four-point methods |
This document specifies three test methods for determining the bending stiffness of paper and paperboard. The test methods differ in the type of loading mode, thus giving rise to the two-point, three-point and four-point bending test methods.
For paper and paperboard in a low thickness range, the two-point bending method and the three-point bending method are suitable.
For corrugated fibreboard and board with a higher thickness, the four-point bending method is recommended.
The measurement conditions are defined in such a way that the test piece is not subjected to any significant permanent deformation during the test, nor is the range of validity of the formulae for calculating the bending stiffness exceeded.
In these bending tests, the test pieces of paper and board are regarded as "beams" as defined by the science of the strength of materials, see Reference [2].
|
Published |
2019-05 |
Edition : 3 |
Number of pages : 10 |
Technical Committee |
85.060
Paper and board
|
| ISO 5629:1983 |
Paper and board — Determination of bending stiffness — Resonance method |
Applies to a wide range of papers and boards, but for some materials, such as multi-ply papers and boards, papers and boards with appreciable curl, some soft papers with grammage below about 40 g/m , the measured numerical value may not be strictly identical with the bending stiffness. It does not apply to corrugated boards.
|
Withdrawn |
1983-12 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
85.060
Paper and board
|
| ISO 5629:2017 |
Paper and board — Determination of bending stiffness — Resonance method |
ISO 5629:2017 specifies a method for the determination of bending stiffness using the resonance method.
This method gives only a single result for each test piece tested, although in general, bending stiffness values may depend on which surface of the material forms the inner surface of the arc resulting from bending forces.
The bending stiffness of a very wide range of papers and boards can be measured using this method. However, for some materials, such as those listed below, the measured numerical values will not be strictly identical with bending stiffness as defined in 3.1:
a) multi-ply papers and boards in which the component plies can move separately during a test;
b) papers and boards with appreciable curl, especially if the axis of the curl is in the long direction of the test piece;
c) some soft papers with grammage below about 40 g/m2.
This method is not applicable to corrugated boards.
|
Published |
2017-12 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
85.060
Paper and board
|
| ISO 5630-1:1982 |
Paper and board — Accelerated ageing — Part 1: Dry heat treatment |
|
Withdrawn |
1982-12 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
85.060
Paper and board
|
| ISO 5630-1:1991 |
Paper and board — Accelerated ageing — Part 1: Dry heat treatment at 105 degrees C |
Specifies a method by dry heat treatment at 105 °C. Is not applicable to certain high purity papers such as are used for insulation in electrical equipment for which ISO 5630-4 is more suitable. Does not give any preference for the test to be made. It is left to the parties concerned to determine which tests are appropriate for the type being evaluated.
|
Published |
1991-02 |
Edition : 2 |
Number of pages : 3 |
Technical Committee |
85.060
Paper and board
|
| ISO 5630-2:1985 |
Paper and board — Accelerated ageing — Part 2: Moist heat treatment at 90 degrees C and 25 % relative humidity |
|
Withdrawn |
1985-11 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
85.060
Paper and board
|
| ISO 5630-3:1986 |
Paper and board — Accelerated ageing — Part 3: Moist heat treatment at 80 degrees C and 65 % relative humidity |
|
Withdrawn |
1986-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
85.060
Paper and board
|
| ISO/TR 10361:1990 |
Textile floor coverings — Production of changes in appearance by means of Vettermann drum and hexapod tumbler testers |
|
Withdrawn |
1990-11 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
97.150
Floor coverings
|
| ISO 5630-3:1996 |
Paper and board — Accelerated ageing — Part 3: Moist heat treatment at 80 degrees C and 65 % relative humidity |
Specifies a procedure for moist heat treatment of paper or board. This method concerns printing and writing papers, but may be used with discretion for other types of paper and board. Not applicable to certain electrical insulating papers. Replaces the first edition.
|
Published |
1996-06 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
85.060
Paper and board
|
| ISO 5630-4:1986 |
Paper and board — Accelerated ageing — Part 4: Dry heat treatment at 120 or 150 degrees C |
Is primarily intended for high purity papers such as are used for insulation in electrical equipment, and does not contain any statement about the tests to be made on the paper. It is left to the parties concerned to determine which tests are appropriate for the type of paper being evaluted.
|
Published |
1986-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
85.060
Paper and board
|
| ISO 5630-5:2008 |
Paper and board — Accelerated ageing — Part 5: Exposure to elevated temperature at 100 degrees C |
ISO 5630-5:2008 specifies a method for accelerating the ageing of printing and writing papers, through the use of elevated temperature, and assessing its effect on the mechanical properties of fold number and tearing resistance, for the purpose of predicting stability to long-term natural ageing.
ISO 5630-5:2008 is applicable to all cellulose-based printing and writing papers, including coated papers and filled papers.
|
Published |
2008-12 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
85.060
Paper and board
|
| ISO 5630-6:2009 |
Paper and board — Accelerated ageing — Part 6: Exposure to atmospheric pollution (nitrogen dioxide) |
ISO 5630-6:2009 specifies a method for accelerating the ageing of printing and writing papers through exposure to nitrogen dioxide gas and assessing the effect on mechanical and optical properties for the purpose of predicting stability to long-term natural ageing that occurs due to exposure to polluted air. It is applicable to all cellulose-based printing and writing papers, including coated papers and filled papers.
|
Published |
2009-06 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
85.060
Paper and board
|
| ISO 5630-7:2014 |
Paper and board — Accelerated ageing — Part 7: Exposure to light |
ISO 5630-7:2014 specifies a method for accelerating the ageing of paper and board through exposure to an elevated light irradiance and for assessing the effect of ageing on optical properties for the purpose of predicting stability to long-term natural ageing that occurs due to exposure to light. It is applicable to all types of paper and board whose surface is white or near white.
|
Withdrawn |
2014-08 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
85.060
Paper and board
|
| ISO 5631-1:2009 |
Paper and board — Determination of colour by diffuse reflectance — Part 1: Indoor daylight conditions (C/2 degrees) |
ISO 5631-1:2009 specifies a method for measuring the colour of paper and board by the diffuse reflectance method with the elimination of specular gloss.
ISO 5631-1:2009 is not applicable to coloured papers or boards which incorporate fluorescent dyes or pigments. It may be used to determine the colour of papers or boards which contain fluorescent whitening agents provided the UV content of the illumination on the test piece has been adjusted to conform to that in the CIE illuminant C, using a fluorescent reference standard provided by an ISO/TC 6 authorized laboratory, as described in ISO 2470-1.
|
Withdrawn |
2009-10 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
85.060
Paper and board
|
| ISO 5631-1:2015 |
Paper and board — Determination of colour by diffuse reflectance — Part 1: Indoor daylight conditions (C/2 degrees) |
ISO 5631-1:2015 specifies a method for measuring the colour of paper and board by the diffuse reflectance method with the elimination of specular gloss.
ISO 5631-1:2015 is not applicable to coloured papers or boards which incorporate fluorescent dyes or pigments. It may be used to determine the colour of papers or boards which contain fluorescent whitening agents provided the UV content of the illumination on the test piece has been adjusted to conform to that in the CIE illuminant C, using a fluorescent reference standard that fulfils the requirements for international fluorescent reference standards of level 3 (IR3) as prescribed by ISO 2469 with an assigned ISO brightness value (C/2°) provided by an authorized laboratory, as described in ISO 2470‑1.
|
Withdrawn |
2015-11 |
Edition : 2 |
Number of pages : 13 |
Technical Committee |
85.060
Paper and board
|
| ISO 5631-1:2022 |
Paper and board — Determination of colour by diffuse reflectance — Part 1: Indoor daylight conditions (C/2°) |
This document specifies a method for measuring the colour of paper and board by the diffuse reflectance method with the elimination of specular gloss.
This document is not applicable to coloured papers or boards which incorporate fluorescent dyes or pigments. It may be used to determine the colour of papers or boards which contain fluorescent whitening agents provided the UV content of the illumination on the test piece has been adjusted to conform to that in the CIE illuminant C, using a fluorescent reference standard that fulfils the requirements for international fluorescent reference standards of level 3 (IR3) as prescribed by ISO 2469 with an assigned ISO brightness value provided by an authorized laboratory, as described in ISO 2470‑1.
|
Published |
2022-07 |
Edition : 3 |
Number of pages : 13 |
Technical Committee |
85.060
Paper and board
|
| ISO 5638:1978 |
Solid fibreboard — Determination of grammage of single layers |
Applies to single layers of glued and laminated solid fibreboard and is applicable to all types of solid fibreboard as defined in ISO 4046, provided that the adhesive dessolves under the conditions specified for the test.
|
Published |
1978-10 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
85.060
Paper and board
|
| ISO 5631-2:2008 |
Paper and board — Determination of colour by diffuse reflectance — Part 2: Outdoor daylight conditions (D65/10 degrees) |
ISO 5631-2:2008 specifies a method for measuring the colour of paper and board by the diffuse reflectance method with the elimination of specular gloss.
It may be used to determine the colour of papers or boards that contain fluorescent whitening agents, provided the UV content of the illumination on the test piece has been adjusted to conform to that in the CIE standard illuminant D65, using a fluorescent reference standard with an assigned CIE whiteness (D65/10°) value provided by an ISO/TC 6 authorized laboratory, as described in ISO 11475.
ISO 5631-2:2008 is not applicable to coloured papers or boards that incorporate fluorescent dyes or pigments.
|
Withdrawn |
2008-12 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
85.060
Paper and board
|
| ISO 5631-2:2014 |
Paper and board — Determination of colour by diffuse reflectance — Part 2: Outdoor daylight conditions (D65/10 degrees) |
ISO 5631-2:2014 specifies a method for measuring the colour of paper and board by the diffuse reflectance method with the elimination of specular gloss.
It can be used to determine the colour of papers or boards that contain fluorescent whitening agents, provided the UV content of the illumination on the test piece has been previously adjusted to give the calibrated colourimetric value corresponding to CIE standard illuminant D65, using a fluorescent reference standard with an assigned CIE whiteness (D65/10°) value provided by an authorized laboratory, as described in ISO 11475.
ISO 5631-2:2014 is not applicable to coloured papers or boards that incorporate fluorescent dyes or pigments.
|
Withdrawn |
2014-07 |
Edition : 2 |
Number of pages : 10 |
Technical Committee |
85.060
Paper and board
|
| ISO 5631-2:2015 |
Paper and board — Determination of colour by diffuse reflectance — Part 2: Outdoor daylight conditions (D65/10 degrees) |
ISO 5631-2:2015 specifies a method for measuring the colour of paper and board by the diffuse reflectance method with the elimination of specular gloss.
It can be used to determine the colour of papers or boards that contain fluorescent whitening agents, provided the UV content of the illumination on the test piece has been previously adjusted to give the calibrated colourimetric value corresponding to CIE standard illuminant D65, using a fluorescent reference standard with an assigned CIE whiteness (D65/10°) value provided by an authorized laboratory, as described in ISO 11475.
ISO 5631-2:2015 is not applicable to coloured papers or boards that incorporate fluorescent dyes or pigments.
|
Withdrawn |
2015-11 |
Edition : 3 |
Number of pages : 13 |
Technical Committee |
85.060
Paper and board
|
| ISO 5631-2:2022 |
Paper and board — Determination of colour by diffuse reflectance — Part 2: Outdoor daylight conditions (D65/10°) |
This document specifies a method for measuring the colour of paper and board by the diffuse reflectance method with the elimination of specular gloss.
It can be used to determine the colour of papers or boards that contain fluorescent whitening agents, provided the UV content of the illumination on the test piece has been previously adjusted to give the calibrated colorimetric value corresponding to CIE standard illuminant D65, using a fluorescent reference standard with an assigned CIE whiteness (D65/10°) value provided by an authorized laboratory, as described in ISO 11475.
This document is not applicable to coloured papers or boards that incorporate fluorescent dyes or pigments.
|
Published |
2022-07 |
Edition : 4 |
Number of pages : 12 |
Technical Committee |
85.060
Paper and board
|
| ISO 5631-3:2008 |
Paper and board — Determination of colour by diffuse reflectance — Part 3: Indoor illumination conditions (D50/2 degrees) |
ISO 5631-3:2008 specifies a method for measuring the colour of paper and board by the diffuse reflectance method with the elimination of specular gloss.
ISO 5631-3:2008 is primarily intended for measuring the colour of paper and board to be used in the graphic arts industry where that industry specifies the measurement of colour under D50/2° conditions in accordance with ISO 13655.
The method may be used to determine the colour of papers or boards that contain fluorescent whitening agents, provided the UV content of the illumination on the test piece has been adjusted to conform to that in the CIE illuminant C, using a fluorescent reference standard provided by an authorized laboratory, as described in ISO 2470-1.
ISO 5631-3:2008 is not applicable to coloured papers or boards that incorporate fluorescent dyes or pigments.
|
Withdrawn |
2008-12 |
Edition : 1 |
Number of pages : 10 |
Technical Committee |
85.060
Paper and board
|
| ISO 5631-3:2014 |
Paper and board — Determination of colour by diffuse reflectance — Part 3: Indoor illumination conditions (D50/2 degrees) |
ISO 5631-3:2014 specifies a method for measuring the colour of paper and board by the diffuse reflectance method with the elimination of specular gloss.
ISO 5631-3:2014 is primarily intended for measuring the colour of paper and board to be used in the graphic arts industry, where that industry specifies the measurement of colour under D50/2° conditions in accordance with ISO 13655. This method differs from ISO 13655, in that, the UV content of the illumination is adjusted to a different level.
The method can be used to determine the colour of papers or boards that contain fluorescent whitening agents, provided the UV content of the illumination on the test piece has been adjusted to conform to that in the CIE illuminant C, using a fluorescent reference standard provided by an authorized laboratory, as described in ISO 2470-1.
ISO 5631-3:2014 is not applicable to coloured papers or boards that incorporate fluorescent dyes or pigments.
|
Withdrawn |
2014-07 |
Edition : 2 |
Number of pages : 10 |
Technical Committee |
85.060
Paper and board
|
| ISO 8254-1:2009 |
Paper and board — Measurement of specular gloss — Part 1: 75 degree gloss with a converging beam, TAPPI method |
ISO 8254-1:2009 specifies a method for measuring the specular gloss of paper at an angle of 75° to the normal to the paper surface. Although its chief application is to coated papers, it may also be used for glossy uncoated papers such as supercalendered papers.
|
Published |
2009-02 |
Edition : 2 |
Number of pages : 10 |
Technical Committee |
85.060
Paper and board
|
| ISO 5631-3:2015 |
Paper and board — Determination of colour by diffuse reflectance — Part 3: Indoor illumination conditions (D50/2 degrees) |
ISO 5631-3:2015 specifies a method for measuring the colour of paper and board by the diffuse reflectance method with the elimination of specular gloss.
ISO 5631-3:2015 is primarily intended for measuring the colour of paper and board to be used in the graphic arts industry, where that industry specifies the measurement of colour under D50/2° conditions in accordance with ISO 13655. This method differs from ISO 13655, in that the UV content of the illumination is adjusted to a different level.
The method can be used to determine the colour of papers or boards that contain fluorescent whitening agents, provided the UV content of the illumination on the test piece has been adjusted to conform to that in the CIE illuminant C, using a fluorescent reference standard that fulfils the requirements for international fluorescent reference standards of level 3 (IR3) as prescribed by ISO 2469 with an assigned ISO brightness value (C/2°) provided by an authorized laboratory, as described in ISO 2470‑1.
ISO 5631-3:2015 is not applicable to coloured papers or boards that incorporate fluorescent dyes or pigments.
|
Withdrawn |
2015-11 |
Edition : 3 |
Number of pages : 13 |
Technical Committee |
85.060
Paper and board
|
| ISO 5631-3:2022 |
Paper and board — Determination of colour by diffuse reflectance — Part 3: Indoor illumination conditions (D50/2°) |
This document specifies a method for measuring the colour of paper and board by the diffuse reflectance method with the elimination of specular gloss.
This document is primarily intended for measuring the colour of paper and board to be used in the graphic arts industry, where that industry specifies the measurement of colour under D50/2° conditions in accordance with ISO 13655. This method differs from ISO 13655, in that the UV content of the illumination is adjusted to a different level.
The method can be used to determine the colour of papers or boards that contain fluorescent whitening agents, provided the UV content of the illumination on the test piece has been adjusted to conform to that in the CIE illuminant C, using a fluorescent reference standard that fulfils the requirements for international fluorescent reference standards of level 3 (IR3) as prescribed by ISO 2469 with an assigned ISO brightness value provided by an authorized laboratory, as described in ISO 2470‑1.
This document is not applicable to coloured papers or boards that incorporate fluorescent dyes or pigments.
|
Published |
2022-07 |
Edition : 4 |
Number of pages : 12 |
Technical Committee |
85.060
Paper and board
|
| ISO 5631:2000 |
Paper and board — Determination of colour (C/2 degrees) — Diffuse reflectance method |
|
Withdrawn |
2000-03 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
85.060
Paper and board
|
| ISO 5633:1983 |
Paper and board — Determination of resistance to water penetration |
Is applicable to papers and boards which have been rendered water resistant or waterproof by internal sizing, by surface sizing, by coating, or by lamination using waterproof laminants , or by any other method, and is not suitable for corrugated fibreboard by may be applied to components of such board.
|
Published |
1983-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
85.060
Paper and board
|
| ISO 5634:1986 |
Paper and board — Determination of grease resistance |
Refers to paper and board used for packaging purposes such as food packaging. The paper and board may be tested either creased or uncreased. The test is primarily intended for foodboard, greaseproof, vegetable parchment and similar products.
|
Withdrawn |
1986-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
85.060
Paper and board
|
| ISO 5634:1986/Cor 1:1992 |
Paper and board — Determination of grease resistance — Technical Corrigendum 1 |
Amends Sub-clause 5.1, Note 1: after "Merck 6981" shall be inserted "(reference according to the German edition of the Merck catalogue)".
|
Withdrawn |
1992-03 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
85.060
Paper and board
|
| ISO 5635:1978 |
Paper — Measurement of dimensional change after immersion in water |
Is suitable for use with most kinds of paper. However, it may not be suitable for some papers, which soaking makes extremely fragile and causes to curl excessively. The property of dimensional change after immersion in water should not be cofused with hydroexpansivity.
|
Published |
1978-10 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
85.060
Paper and board
|
| ISO 5636-1:1984 |
Paper and board — Determination of air permeance (medium range) — Part 1: General method |
Specfies basic requirements for apperatus and general operating procedures for determining the air permeance of paper and board in the medium air permeance range, and is applicable to papers and boards having air permeances between 1 x 10- and 1 x 10 m/(Pa.s), being unsuitable for rough-surface papers such as creped and corrugared papers, which cannot be securely clamped to avoid leakage.
|
Withdrawn |
1984-04 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
85.060
Paper and board
|
| ISO 5636-2:1984 |
Paper and board — Determination of air permeance (medium range) — Part 2: Schopper method |
Specfies detailed requirements and operating procedures applicable to specific types of apparatus, and is applicable to papers and boards having air permeances between 1 x 10- and 1 x 10 m/(Pa.s), being unsuitable for rough-surface papers such as creped and corrugared papers, which cannot be securely clamped to avoid leakage.
|
Withdrawn |
1984-04 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
85.060
Paper and board
|
| ISO 5636-3:1992 |
Paper and board — Determination of air permeance (medium range) — Part 3: Bendtsen method |
The method determines air permeance in the medium range. It is applicable to papers and boards having air permeance between 0,35 µm/(Pa·s) und 15 µm/(Pa·s). It is unsuitable for rough surfaced papers and boards, such as creped and corrugated papers, which cannot be securely clamped to avoid leakage. Annex A considers maintenance of Bendtsen testers, Annex B calibration of capillary tubes and variable area flowmeters.
|
Withdrawn |
1992-09 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
85.060
Paper and board
|
| ISO 5636-3:2013 |
Paper and board — Determination of air permeance (medium range) — Part 3: Bendtsen method |
ISO 5636-3:2013 specifies the Bendtsen method for determining the air permeance of paper and board using the Bendtsen apparatus.
It is applicable to papers and boards which have air permeances between 0,35 µm/(Pa·s) and 15 µm/(Pa·s) when tested with the Bendtsen apparatus.
It is unsuitable for rough-surfaced materials which cannot be securely clamped to avoid leakage.
|
Published |
2013-11 |
Edition : 3 |
Number of pages : 14 |
Technical Committee |
85.060
Paper and board
|
| ISO 5636-4:1986 |
Paper and board — Determination of air permeance (medium range) — Part 4: Sheffield method |
Specfies detailed requirements and operating procedures applicable to specific types of apparatus, and is applicable to papers and boards having air permeances between 0,02 and 25 m/(Pa.s), being unsuitable for rough-surface papers such as creped and corrugared papers, which cannot be securely clamped to avoid leakage.
|
Withdrawn |
1986-07 |
Edition : 1 |
Number of pages : 7 |
Technical Committee |
85.060
Paper and board
|
| ISO 5636-4:2005 |
Paper and board — Determination of air permeance (medium range) — Part 4: Sheffield method |
ISO 5636-4:2005 specifies a method of determining the air flow rate through unit area of a sheet of paper or board, under unit pressure difference using apparatus called the Sheffield instrument.
The method is applicable to papers and boards having air permeances between 0,02 micrometres per pascal second and 25 micrometres per pascal second. The method is not suitable for papers and boards with a rough surface, such as crêpe paper and corrugated papers, which cannot be securely clamped to avoid surface leakage.
|
Withdrawn |
2005-02 |
Edition : 2 |
Number of pages : 12 |
Technical Committee |
85.060
Paper and board
|
| ISO 5636-4:2013 |
Paper and board — Determination of air permeance (medium range) — Part 4: Sheffield method |
ISO 5636-4:2013 specifies the Sheffield method for determining the air permeance of paper and board using the Sheffield apparatus.
It is applicable to papers and boards which have air permeances between 0,02 µm/(Pa·s) and 25 µm/(Pa·s) when tested with the Sheffield apparatus.
It is unsuitable for rough-surfaced materials, which cannot be securely clamped to avoid leakage.
|
Published |
2013-11 |
Edition : 3 |
Number of pages : 13 |
Technical Committee |
85.060
Paper and board
|
| ISO 5636-5:1986 |
Paper and board — Determination of air permeance (medium range) — Part 5: Gurley method |
Specfies detailed requirements and operating procedures applicable to specific types of apparatus, and is applicable to papers and boards having air permeances between 0,1 and 100 m/(Pa.s), being unsuitable for rough-surface papers such as creped and corrugared papers, which cannot be securely clamped to avoid leakage.
|
Withdrawn |
1986-12 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
85.060
Paper and board
|
| ISO 5636-5:1986/Cor 1:1990 |
Paper and board — Determination of air permeance (medium range) — Part 5: Gurley method — Technical Corrigendum 1 |
|
Withdrawn |
1990-09 |
Edition : 1 |
Number of pages : 1 |
Technical Committee |
85.060
Paper and board
|
| ISO 5636-5:2003 |
Paper and board — Determination of air permeance and air resistance (medium range) — Part 5: Gurley method |
ISO 5636-5:2003 specifies the Gurley method of determining the air permeance of paper and board. It is applicable to papers and boards which have air permeances between 0,1 micrometres per pascal second and 100 micrometres per pascal second. It is unsuitable for rough-surfaced materials, which cannot be securely clamped to avoid leakage.
This method may also be used to determine the air resistance of paper and board.
|
Withdrawn |
2003-06 |
Edition : 2 |
Number of pages : 8 |
Technical Committee |
85.060
Paper and board
|
| ISO 5636-5:2013 |
Paper and board — Determination of air permeance (medium range) — Part 5: Gurley method |
ISO 5636-5:2013 specifies the Gurley method for determining the air permeance of paper and board using an air resistance tester, the Gurley apparatus.
It is applicable to papers and boards which have air permeances between 0,1 µm/(Pa⋅s) and 100 µm/(Pa⋅s) when tested with the Gurley apparatus.
It is unsuitable for rough-surfaced materials, which cannot be securely clamped to avoid leakage.
ISO 5636-5:2013 may also be used to determine the air resistance of paper and board.
|
Published |
2013-11 |
Edition : 3 |
Number of pages : 12 |
Technical Committee |
85.060
Paper and board
|
| ISO 5636-6:2015 |
Paper and board — Determination of air permeance (medium range) — Part 6: Oken method |
ISO 5636-6:2015 specifies the Oken method for determining the air permeance and air resistance of paper and board. There is no limitation on the measuring range of air permeance or air resistance of papers and boards. It is unsuitable for rough-surfaced materials, which cannot be securely clamped to avoid leakage.
|
Published |
2015-05 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
85.060
Paper and board
|
| ISO 5647:1990 |
Paper and board — Determination of titanium dioxide content |
Specifies a method for determining titanium dioxide content in all kinds of paper and board, in particular coated or filled products. It comprises two procedures for the final determination of titanium based on spectrophotometry and flame atomic absorption spectrophotometry, respectively. The limits of determination depend on the amount of sample taken. Titanium present in other forms will not interfere in the determination.
|
Withdrawn |
1990-11 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
85.060
Paper and board
|
| ISO 5647:2019 |
Paper and board — Determination of titanium dioxide content |
This document specifies a method for determining titanium dioxide content in all kinds of paper and board, in particular coated or filled products. It comprises two procedures for the final determination of titanium, one of them relying on spectrophotometry and the other on flame atomic absorption spectrophotometry. The limits of the determination depend on the amount of sample taken (8.1).
NOTE The method is designed for the determination of titanium dioxide. Titanium present in other forms, for example as a constituent of clay, will not interfere in the determination.
|
Published |
2019-05 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
85.060
Paper and board
|
| ISO 5651:1978 |
Paper, board and pulps — Units for expressing properties |
|
Withdrawn |
1978-12 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 5651:1989 |
Paper, board and pulps — Units for expressing properties |
Applies to properties of paper, board and pulps, but excludes fibre building boards. Two separate tables give recommended units for use in connection with test methods which are already, and which are not at present, the subject of international standards.
|
Withdrawn |
1989-01 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 6587:1980 |
Paper, board and pulps — Determination of conductivity of aqueous extracts |
|
Withdrawn |
1980-12 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 6587:1992 |
Paper, board and pulps — Determination of conductivity of aqueous extracts |
The method described is applicable to all kinds of paper, board and pulps, except for papers used for electrical purposes. For high purity papers used for electrical purposes, the method used should be that given in IEC 554-2. Conductivity is measured by means of a conductivity meter or resistance bridge, using alternating current.
|
Withdrawn |
1992-04 |
Edition : 2 |
Number of pages : 4 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 6587:2021 |
Paper, board and pulps — Determination of conductivity of aqueous extracts |
This document specifies a method for the determination of the conductivity of aqueous extracts of paper, board or pulp, these extracts having been prepared by a hot or cold method.
The method is applicable to all kinds of paper, board and pulps, except for papers used for electrical purposes. For high purity papers used for electrical purposes, see method given in EN 60554‑2.
|
Published |
2021-11 |
Edition : 3 |
Number of pages : 6 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 6588-1:2005 |
Paper, board and pulps — Determination of pH of aqueous extracts — Part 1: Cold extraction |
ISO 6588-1:2005 specifies a method for the determination of the pH-value defined by the electrolytes extractable by cold water from a sample of paper, board or pulp.
ISO 6588-1:2005 is applicable to all types of paper, board and pulp.
|
Withdrawn |
2005-05 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 6588-1:2012 |
Paper, board and pulps — Determination of pH of aqueous extracts — Part 1: Cold extraction |
ISO 6588-1:2012 specifies a method for the determination of the pH-value defined by the electrolytes extractable by cold water from a sample of paper, board or pulp.
ISO 6588-1:2012 is applicable to all types of paper, board and pulp.
As the quantity of extractable ionic material approaches zero, as in the case of highly purified pulps, the precision of the method becomes poor because of the difficulties encountered in making pH measurements on water containing little electrolytic material.
Since the extraction in ISO 6588-1:2012 is performed with distilled or deionised water, the pH-value measured will sometimes be different (e.g. for fully bleached pulp) from the pH-value measured under mill process conditions in which various types of process waters, e.g. chemically treated river water containing electrolytes, are used.
It is necessary to be aware that the results will not be the same when measuring pH according to ISO 6588-1:2012 and to ISO 29681. The difference can be significant especially when measuring pulps having a low ionic strength.
ISO 6588-2 differs from ISO 6588-1:2012 only as regards the extraction conditions. No general guidance can be given as to which of the two procedures (hot or cold) is best suited in a particular situation.
For cellulosic papers used for electrical purposes, the method used should be that given in IEC 60554-2
|
Withdrawn |
2012-11 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 6588-1:2020 |
Paper, board and pulps — Determination of pH of aqueous extracts — Part 1: Cold extraction |
This document specifies a method for the determination of the pH-value defined by the electrolytes extractable by cold water from a sample of paper, board or pulp.
This document is applicable to all types of paper, board and pulp.
As the quantity of extractable ionic material approaches zero, as in the case of highly purified pulps, the precision of the method becomes poor because of the difficulties encountered in making pH measurements on water containing little electrolytic material.
Since the extraction in this document is performed with distilled or deionised water, the pH-value measured will sometimes be different (e.g. for fully bleached pulp) from the pH-value measured under mill process conditions in which various types of process waters, e.g. chemically treated river water containing electrolytes, are used. In such cases, ISO 29681 should be used instead, as it is specifically applicable to bleached pulps from virgin fibres and to pulp samples having a low ionic strength for which the pH value will give more realistic results related to mill conditions than those obtained with this document.
For cellulosic papers used for electrical purposes, the method used should be that given in IEC 60554‑2[4].
|
Withdrawn |
2020-02 |
Edition : 3 |
Number of pages : 7 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 6588-1:2021 |
Paper, board and pulps — Determination of pH of aqueous extracts — Part 1: Cold extraction |
This document specifies a method for the determination of the pH-value defined by the electrolytes extractable by cold water from a sample of paper, board or pulp.
This document is applicable to all types of paper, board and pulp.
As the quantity of extractable ionic material approaches zero, as in the case of highly purified pulps, the precision of the method becomes poor because of the difficulties encountered in making pH measurements on water containing little electrolytic material.
Since the extraction in this document is performed with distilled or deionised water, the pH-value measured can sometimes be different (e.g. for fully bleached pulp) from the pH-value measured under mill process conditions, in which various types of process waters, such as chemically treated river water containing electrolytes, are used. In such cases, ISO 29681 can be used instead, as it is specifically applicable to bleached pulps from virgin fibres and to pulp samples having a low ionic strength for which the pH value gives more realistic results related to mill conditions than those obtained with this document.
For cellulosic papers used for electrical purposes, the method used can be that given in IEC 60554‑2[5].
|
Published |
2021-11 |
Edition : 4 |
Number of pages : 7 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 6588-2:2005 |
Paper, board and pulps — Determination of pH of aqueous extracts — Part 2: Hot extraction |
ISO 6588-2:2005 specifies a method for the determination of the pH-value defined by the electrolytes extractable by hot water from a sample of paper, board or pulp.
ISO 6588-2:2005 is applicable to all kinds of paper, board and pulp.
|
Withdrawn |
2005-05 |
Edition : 1 |
Number of pages : 6 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 6588-2:2012 |
Paper, board and pulps — Determination of pH of aqueous extracts — Part 2: Hot extraction |
This part of ISO 6588 specifies a method for the determination of the pH-value defined by the electrolytes extractable by hot water from a sample of paper, board or pulp.
This part of ISO 6588 is applicable to all kinds of paper, board and pulp.
As the quantity of extractable ionic material approaches zero, as in the case of highly purified pulps, the precision of the method becomes poor because of the difficulties encountered in making pH measurements on water containing little electrolytic material.
Since the extraction in this part of ISO 6588 is performed with distilled or deionised water, the pH-value measured will sometimes be different (e.g. fully bleached pulp) from the pH-value measured under mill process conditions in which various types of process waters, e.g. chemically treated river water containing electrolytes, are used.
It is necessary to be aware that the results will not be the same when measuring pH according to this part of ISO 6588 when compared to ISO 29681. The differences can be significant especially when measuring pulps having a low ionic strength.
ISO 6588-1 differs from this part of ISO 6588 only as regards the extraction conditions. No general guidance can be given as to which of the two procedures (hot or cold) is best suited in a particular situation.
For cellulosic papers used for electrical purposes, the method used should be that given in IEC 60554-2.
|
Withdrawn |
2012-11 |
Edition : 2 |
Number of pages : 7 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 6588-2:2020 |
Paper, board and pulps — Determination of pH of aqueous extracts — Part 2: Hot extraction |
This document specifies a method for the determination of the pH-value defined by the electrolytes extractable by hot water from a sample of paper, board or pulp.
This document is applicable to all kinds of paper, board and pulp.
As the quantity of extractable ionic material approaches zero, as in the case of highly purified pulps, the precision of the method becomes poor because of the difficulties encountered in making pH measurements on water containing little electrolytic material.
Since the extraction in this document is performed with distilled or deionised water, the pH-value measured will sometimes be different (e.g. fully bleached pulp) from the pH-value measured under mill process conditions in which various types of process waters, e.g. chemically treated river water containing electrolytes, are used. In such cases, ISO 29681 can be used instead, as it is specifically applicable to bleached pulps from virgin fibres and to pulp samples having a low ionic strength for which the pH value will give more realistic results related to mill conditions than those obtained with this document. For cellulosic papers used for electrical purposes, the method used can be that given in IEC 60554-2[4].
|
Withdrawn |
2020-03 |
Edition : 3 |
Number of pages : 7 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 6588-2:2021 |
Paper, board and pulps — Determination of pH of aqueous extracts — Part 2: Hot extraction |
This document specifies a method for the determination of the pH-value defined by the electrolytes extractable by hot water from a sample of paper, board or pulp.
This document is applicable to all kinds of paper, board and pulp.
As the quantity of extractable ionic material approaches zero, as in the case of highly purified pulps, the precision of the method becomes poor because of the difficulties encountered in making pH measurements on water containing little electrolytic material.
Since the extraction in this document is performed with distilled or deionised water, the pH-value measured can sometimes be different (e.g. fully bleached pulp) from the pH-value measured under mill process conditions in which various types of process waters, such as chemically treated river water containing electrolytes, are used. In such cases, ISO 29681 can be used instead, as it is specifically applicable to bleached pulps from virgin fibres and to pulp samples having a low ionic strength for which the pH value gives more realistic results related to mill conditions than those obtained with this document. For cellulosic papers used for electrical purposes, the method used can be that given in IEC 60554-2[5].
|
Published |
2021-11 |
Edition : 4 |
Number of pages : 7 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 6588:1981 |
Paper, board and pulps — Determination of pH of aqueous extracts |
Is applicable to all kinds of paper, board and pulps yielding an extract having a conductivity exceeding 0.2 mS/m when determined in accordance with ISO 6587, except for papers used for electrical purposes. For high purity papers used for electrical purposes, the method should be that given in IEC Publication 554-2.
|
Withdrawn |
1981-04 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
|
| ISO 7263:1985 |
Corrugating medium — Determination of the flat crush resistance after laboratory fluting |
|
Withdrawn |
1985-07 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
85.060
Paper and board
|
| ISO 7263:1994 |
Corrugating medium — Determination of the flat crush resistance after laboratory fluting |
Cancels and replaces the first edition (1985). Specifies two methods for the determination of the flat crush resistance of corrugating medium after laboratory fluting. The procedures are applicable to any paper intended to be used, after fluting, in the manufacture of corrugated fibreboard.
|
Withdrawn |
1994-12 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
85.060
Paper and board
|
| ISO 7263:2008 |
Corrugating medium — Determination of the flat crush resistance after laboratory fluting |
ISO 7263:2008 specifies two methods for the determination of the flat crush resistance of corrugating medium after laboratory fluting.
The procedures are applicable to any corrugating medium intended to be used, after fluting, in the manufacture of corrugated board.
|
Withdrawn |
2008-12 |
Edition : 3 |
Number of pages : 8 |
Technical Committee |
85.060
Paper and board
|
| ISO/CD 7763 |
Testing of paper and board — Compressive strength of an in s-shape fixed sample |
This standard specifies a test method for determining the compressive strength of a sample fixed in s-shape in the machine direction.
The application of this standard is recommended for papers with a grammage of 80 g/m2 to 220 g/m2, but it is also applicable to papers of different grammage.
|
Under development |
|
Edition : 1 |
|
Technical Committee |
85.060
Paper and board
|
| ISO 8226-1:1985 |
Paper and board — Measurement of hygroexpansivity — Part 1: Hygroexpansivity up to a maximum relative humidity of 68 % |
|
Withdrawn |
1985-11 |
Edition : 1 |
Number of pages : 3 |
Technical Committee |
85.060
Paper and board
|
| ISO 8226-1:1994 |
Paper and board — Measurement of hygroexpansivity — Part 1: Hygroexpansivity up to a maximum relative humidity of 68 % |
Cancels and replaces the first edition (1985). Specifies a method for the determination of the hygroexpansivity of paper and board when subjected to a change in the relative humidity. Applicable to paper and board generally. Not suitable for crêpe papers and corrugated fibreboard.
|
Published |
1994-12 |
Edition : 2 |
Number of pages : 6 |
Technical Committee |
85.060
Paper and board
|
| ISO 8226-2:1990 |
Paper and board — Measurement of hygroexpansivity — Part 2: Hygroexpansivity up to a maximum relative humidity of 86 % |
This part specifies a method for the determination of hygroexpansivity when the paper or board is subjected to a change in the relative humidity with which it is in equilibrium from (33 2) % to (84 2) %. The purpose is to cover applications of paper and board intended to be used in high humidity conditions. It may also be useful in determining the effect of excessive moisture to which paper may be subjected for short periods during some printing processes. The method is generally applicable. However, it is not suitable for cr pe papers and corrugated fibreboard.
|
Published |
1990-12 |
Edition : 1 |
Number of pages : 4 |
Technical Committee |
85.060
Paper and board
|
| ISO 8254-1:1999 |
Paper and board — Measurement of specular gloss — Part 1: 75 degree gloss with a converging beam, TAPPI method |
|
Withdrawn |
1999-11 |
Edition : 1 |
Number of pages : 8 |
Technical Committee |
85.060
Paper and board
|
| ISO 8254-2:2003 |
Paper and board — Measurement of specular gloss — Part 2: 75 degree gloss with a parallel beam, DIN method |
ISO 8254-2:2003 specifies a photometric test method for the assessment of visual gloss by means of a reflectometer value measured at an angle of 75 degrees. It is applicable to plane paper and board surfaces of low gloss, commonly called matt papers and boards having reflectance values, measured according to ISO 8254-2:2003, between 0 and approximately 20. Materials containing optical brightening agents may be measured.
|
Withdrawn |
2003-01 |
Edition : 1 |
Number of pages : 13 |
Technical Committee |
85.060
Paper and board
|
| ISO 8254-2:2016 |
Paper and board — Measurement of specular gloss — Part 2: 75 degree gloss with a parallel beam, DIN method |
ISO 8254-2:2016 specifies a photometric test method for the assessment of visual gloss by means of a reflectometer value measured at an angle of 75°. It is applicable to plane paper and board surfaces of gloss levels below 65, measured according to ISO 8254-2:2016. It should be the preferred method for paper and board surfaces of gloss levels below 20, measured according to ISO 8254-2:2016. Materials containing optical brightening agents may be measured.
|
Published |
2016-07 |
Edition : 2 |
Number of pages : 11 |
Technical Committee |
85.060
Paper and board
|
| ISO 8254-3:2004 |
Paper and board — Measurement of specular gloss — Part 3: 20 degree gloss with a converging beam, TAPPI method |
ISO 8254-3:2004 specifies a method for measuring the specular gloss of paper and board at an angle of 20° to the normal to the paper surface. It is applicable chiefly to highly glossy surfaces, such as cast-coated, lacquered, highly varnished or waxed papers and high-gloss ink films.
|
Withdrawn |
2004-11 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
85.060
Paper and board
|
| ISO 8254-3:2016 |
Paper and board — Measurement of specular gloss — Part 3: 20 degree gloss with a converging beam, TAPPI method |
ISO 8254-3:2016 specifies a method for measuring the specular gloss of paper and board at an angle of 20° to the normal to the paper surface. It is applicable chiefly to highly glossy surfaces, such as cast-coated, lacquered, highly varnished or waxed papers and high-gloss ink films.
NOTE This part of ISO 8254 has been developed from TAPPI T653[2], ISO 2813[1] and from ISO 8254‑1.
|
Published |
2016-04 |
Edition : 2 |
Number of pages : 10 |
Technical Committee |
85.060
Paper and board
|
| ISO 8784-1:1987 |
Paper and board — Determination of microbiological properties — Part 1: Total bacterial count |
Is applicable to most kinds of paper and board, especially food grades, and is not suitable for materials such as vegetable parchment or wet-strength paper which cannot be readily disintegrated.
|
Withdrawn |
1987-01 |
Edition : 1 |
Number of pages : 5 |
Technical Committee |
85.060
Paper and board
;
07.100.99
Other standards related to microbiology
|
| ISO 8784-1:2005 |
Pulp, paper and board — Microbiological examination — Part 1: Total count of bacteria, yeast and mould based on disintegration |
ISO 8784-1:2005 specifies a method for determining the total number of colony-forming units of bacteria, yeast and moulds in dry market pulp, paper and paperboard after disintegration. The enumeration relates to specific media.
ISO 8784-1:2005 is applicable to most kinds of paper and paperboard, especially those grades intended to come into contact with foodstuffs.
|
Withdrawn |
2005-07 |
Edition : 2 |
Number of pages : 9 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
;
07.100.99
Other standards related to microbiology
|
| ISO 8784-1:2014 |
Pulp, paper and board — Microbiological examination — Part 1: Enumeration of bacteria and bacterial spores based on disintegration |
ISO 8784-1:2014 specifies a method for determining the total number of colony-forming units of bacteria and bacterial spores in dry market pulp, paper, and paperboard after disintegration. The enumeration relates to specific media.
|
Published |
2014-12 |
Edition : 3 |
Number of pages : 14 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
;
07.100.99
Other standards related to microbiology
|
| ISO 8784-2 |
Pulp, paper and board — Microbiological examination — Part 2: Enumeration of bacteria, yeast and mould on surface |
|
Under development |
|
Edition : 1 |
|
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
;
07.100.99
Other standards related to microbiology
|
| ISO 8784-3:2022 |
Pulp, paper and board — Microbiological examination — Part 3: Enumeration of yeast and mould based on disintegration |
This document specifies a method for determining the total number of colony-forming units of yeast and mould in dry market pulp, paper and paperboard after disintegration. The enumeration relates to specific media.
|
Published |
2022-04 |
Edition : 1 |
Number of pages : 9 |
Technical Committee |
85.040
Pulps
;
85.060
Paper and board
;
07.100.99
Other standards related to microbiology
|
| ISO 11093-5:2009/Cor 1:2010 |
Paper and board — Testing of cores — Part 5: Determination of characteristics of concentric rotation — Technical Corrigendum 1 |
|
Withdrawn |
2010-05 |
Edition : 2 |
Number of pages : 1 |
Technical Committee |
85.060
Paper and board
|
| ISO 8787:1986 |
Paper and board — Determination of capillary rise — Klemm method |
Is intended for unsized papers such as blotting papers and other papers having a relatively high water absorbency, and is not recommended for materials having a cappillary rise of less than 5 mm, for which tests such as per ISO 535 may be more suitable.
|
Published |
1986-08 |
Edition : 1 |
Number of pages : 2 |
Technical Committee |
85.060
Paper and board
|